Maruti - Celerio - Owners Manual - 2015 - 2015

India's No. 1 Car Exchange Programme OWNER'S MANUAL & SERVICE BOOKLET ER E AU CODE 02/03/2015/5000 Palam Gurgaon Road, Gurgaon - 122 015 (Haryana) www.marutisuzuki.com ED MARUTI SUZUKI INDIA LIMITED O RI S TH S Service Division 99011M76M02-74E 1800 102 1800 PEACE OF MIND Keep With Vehicle At All Times. Contains Important Information On Safety, Operation & Maintenance. VIC Part No. 99011M76M02-74E ENG. March, 2015 India's No. 1 Car Exchange Programme OWNER'S MANUAL & SERVICE BOOKLET ER E AU CODE 02/03/2015/5000 ED MARUTI SUZUKI INDIA LIMITED Palam Gurgaon Road, Gurgaon - 122 015 (Haryana) www.marutisuzuki.com O RI S TH S Service Division 99011M76M03-74E 1800 102 1800 PEACE OF MIND Keep With Vehicle At All Times. Contains Important Information On Safety, Operation & Maintenance. VIC Part No. 99011M76M03-74E ENG. March, 2015 This Owner’s manual & service booklet applies to CELERIO models produced by MARUTI SUZUKI INDIA LIMITED. Prepared by MARUTI SUZUKI INDIA LIMITED Service Division March, 2015 Part No. 99011M76M02-74E Printed in India Note : The illustrated model is one of the CELERIO series Accessories shown in the picture are not part of standard equipment c COPYRIGHT MARUTI SUZUKI INDIA LIMITED 2015 For round-the-clock on-road assistance, call Maruti On-road Service at 1800 102 1800# #No STD code to be prefixed. This Owner’s manual & service booklet applies to CELERIO models produced by MARUTI SUZUKI INDIA LIMITED. Prepared by MARUTI SUZUKI INDIA LIMITED Service Division March, 2015 Part No. 99011M76M03-74E Printed in India Note : The illustrated model is one of the CELERIO series Accessories shown in the picture are not part of standard equipment c COPYRIGHT MARUTI SUZUKI INDIA LIMITED 2015 For round-the-clock on-road assistance, call Maruti On-road Service at 1800 102 1800# #No STD code to be prefixed. Celerio Pankaj Narula Executive Director (Service) Dear Sir/Madam, Thank you for choosing a Maruti Suzuki vehicle. I hope our dealership team took good care while delivering the vehicle to you. Celerio Your vehicle is equipped with state-of-the-art technologies. To get the best performance from your vehicle (and ensure it is trouble-free), kindly get your vehicle serviced periodically, as per the maintenance schedule in your Owner's Manual. Please make sure the service is done at a Maruti Suzuki authorized workshop for best results. For any accessories that you wish to fit on to your vehicle, please contact any of our authorized dealers for assistance. Kindly appreciate that any tampering of wiring harness to fit accessories may cause the vehicle to malfunction. Thank you once again for choosing a Maruti Suzuki vehicle. I wish you many years of safe and happy driving. Yours sincerely Celerio MARUTI SUZUKI INDIA LIMITED Palam Gurgaon Road, Gurgaon-122015 www.marutisuzuki.com (Pankaj Narula) “WARNING” Vehicle may break-down, meet with an accident or catch fire due to 1. Installation of - High wattage bulbs - Non genuine lamps / horns - Modified suspension / wheels - Non genuine parts / accessories etc. 2. Retrofitment of LPG / CNG fuel systems/kits. 3. Usage of domestic LPG. 4. Short circuiting due to tampering of wiring harness. CAUTION: DO NOT STORE OR CARRY INFLAMMABLE MATERIALS IN THE VEHICLE. Avoid driving into or starting the vehicle in a heavily water logged area. Vehicle may breakdown or engine may fail due to 1. Water entry into the engine. 2. Short circuiting of the electrical systems. If the vehicle is stuck in deep water, do not start / crank the vehicle until the level of water drops below the level of exhaust pipe. NOTE: IF THE VEHICLE IS SUBMERGED IN WATER, REPORT AUTHORIZED WORKSHOP. TO THE NEAREST 76MH1-74E TABLE OF CONTENTS FUEL RECOMMENDATION 1 BEFORE DRIVING 2 OPERATING YOUR VEHICLE 3 DRIVING TIPS 4 OTHER CONTROLS AND EQUIPMENT 5 VEHICLE LOADING AND TOWING 6 INSPECTION AND MAINTENANCE 7 EMERGENCY SERVICE 8 APPEARANCE CARE 9 GENERAL INFORMATION 10 SPECIFICATIONS 11 SERVICE NETWORK 12 1 76MH1-74E 76MH1-74E FOREWORD This manual is an essential part of your vehicle and should remain with the vehicle when resold or otherwise transferred to a new owner or operator. Please read this manual carefully before operating your new MARUTI SUZUKI and review the manual from time to time. It contains important information on safety, operation and maintenance. You are invited to avail the three Free Inspection Services as described in the manual. Three free inspection coupons are attached to this manual. Please show this manual to your dealer while you take your MARUTI SUZUKI for any Service. To prolong the life of your vehicle and reduce maintenance cost, the periodic maintenance must be carried out according to “PERIODIC MAINTENANCE SCHEDULE” described in “INSPECTION AND MAINTENANCE” section of this manual. It is essential for preventing trouble and accidents to ensure your satisfaction and safety. Daily inspection and care as per “DAILY INSPECTION CHECKLIST” described in the “INSPECTION AND MAINTENANCE” section of this manual is essential for prolonging the life of the vehicle and for safe driving. 2 MARUTI SUZUKI INDIA LIMITED believes in conservation and protection of Earth’s natural resources. To that end, we encourage every vehicle owner to recycle, trade-in or properly dispose of, as appropriate, used Engine Oil, coolant and other fluids, batteries and tyres etc. MARUTI SUZUKI INDIA LIMITED All information in this manual is based on the latest product information available at the time of publication. Due to improvements or other changes, there may be discrepancies between information in this manual and your vehicle. MARUTI SUZUKI INDIA LIMITED reserves the right to make production changes at any time, without notice and without incurring any obligation to make the same or similar changes to vehicles previously built or sold. This vehicle may not comply with standards or regulations of other countries. Before attempting to register this vehicle in any other country, check all applicable regulations and make any necessary modifications. 0-1 76MH1-74E IMPORTANT MODIFICATION WARNING WARNING/ CAUTION/NOTICE/ NOTE Please read this manual and follow its instructions carefully. To emphasize special information, the symbol and the words WARNING, CAUTION, NOTICE and NOTE have special meanings. Pay particular attention to messages highlighted by these signal words: WARNING Do not modify your vehicle. Modification could adversely affect safety, handling, performance, or durability and may violate governmental regulations. In addition, damage or performance problems resulting from modification may not be covered under warranty. WARNING Indicates a potential hazard that could result in death or serious injury. CAUTION Indicates a potential hazard that could result in minor or moderate injury. NOTICE Indicates a potential hazard could result in vehicle damage. 75F135 The circle with a slash in this manual means “Don’t do this” or “Don’t let this happen”. NOTICE Improper installation of mobile communication equipment such as cellular telephones or CB (Citizen’s Band) radios may cause electronic interference with your vehicle’s ignition system, resulting in vehicle performance problems. Consult your MARUTI SUZUKI dealer for advice on installing such mobile communication equipment. that WARNING NOTE: Indicates special information to make maintenance easier or instructions clearer. 0-2 Severe damage may be caused by the use of either poor quality fuel and/or lubricants not recommended by MARUTI SUZUKI. 3 55KS0-74E 76MH1-74E VEHICLE DETAILS MODEL CHASSIS NO. ENGINE NO. KEY NO. DATE OF DELIVERY ODOMETER READING (KM) BATTERY MAKE SR.NO. BATCH CODE OWNER’S NAME & ADDRESS ________________________________________________________________________________ _________________________________________________________________________________________________________ ______________________________________________________________________TEL.NO. ____________________________ ADRESS/STAMP OF SELLING DEALER SELLING DEALER CODE SHOWROOM WORKSHOP IMPORTANT INFORMATION TO CUSTOMER Dear Customer, For any assistance with regard to our product, please contact General Manager/Works Manager at any of our Dealer or Authorised Service Station. For additional enquiry you may contact our Regional Office or Service Department. The Addresses and Phone nos. are given in Service Network section of this Manual. 4 0-3 76MH1-74E MAINTENANCE SERVICE RECORD DATE OF SERVICE KIND OF SERVICE MILEAGE (KM) DESCRIPTION OF JOB NAME OF SERVICING DEALER/ MASS JOB CARD NO. MECHANICS SIGNATURE F: .... FREE SERVICE, P:.... PAID SERVICE, W:.... WARRANTY JOB, A:.... ACCIDENTAL JOB 0-4 5 55KS0-74E 76MH1-74E WARRANTY POLICY Maruti Suzuki India Limited (hereinafter called “Maruti Suzuki”), warrants that each new Maruti Suzuki vehicle distributed in India by Maruti Suzuki and sold by an authorised Maruti Suzuki dealer will be free, under normal use and service, from any defects in material and workmanship at the time of manufacture SUBJECT TO THE FOLLOWING TERMS AND CONDITIONS: (1) Qualification: To qualify for this warranty: (a) The Maruti Suzuki vehicle must be delivered by Maruti Suzuki authorised dealer and set-up, serviced by Maruti Suzuki authorised dealer / service station. (b) The warranty registration card in respect of each vehicle must be completed by the dealer at the time of delivery of the vehicle and dealer should retain the same. (2) Term: The term of the warranty shall be twenty-four (24) months or 40,000 kilometers (whichever occurs first) from the date of delivery to the first owner. (3) Maruti Suzuki Warranty Obligation: If any defect(s) should be found in a Maruti Suzuki vehicle within the term stipulated above, Maruti Suzuki’s only obligation is to repair or replace at its sole discretion any part shown to be defective, with a new part or the equivalent at no cost to the owner for parts or labour, when Maruti Suzuki acknowledges that such a defect is attributable to faulty material or workmanship at the time of manufacture. The owner is responsible for any repair or replacements which are not covered by this warranty. 6 (4) Limitation: This warranty shall not apply to: 1) Normal maintenance service required other than the three free services, including without limitation, oil and fluid changes, headlight aiming, fastener retightening, wheel balancing, wheel alignment and tyre rotation, cleaning of injectors, adjustments of carburettor, ignition timing, clutch and valve clearance. 2) The replacement of normal wear parts including without limitation, bulbs, tyres and tubes, spark plugs, belts, hoses, filters, wiper blades, brushes, contact points, fuses, clutch disc, brake shoes, brake pads, cable and all rubber parts (except oil seal and glass run). 3) Any vehicle which has been used for competition or racing. 4) Any repairs or replacement required as a result of accidents or collision. 5) Any defects caused by misuse, negligence, abnormal use or insufficient care. 6) Any vehicle which has been modified or altered, including without limitation, the installation of performance accessories. 7) Any vehicle on which parts or accessories not approved by Maruti Suzuki have been used. 8) Any vehicle which has not been operated in accordance with the operating instructions in the Maruti Suzuki Owner’s Manual. 9) Any vehicle which has not received, during the warranty term, the service inspections prescribed in the Maruti Suzuki Owner’s Manual. 10) Any vehicle which has been assembled, disassembled, adjusted or repaired by other than an Maruti Suzuki authorised dealer/service station. 0-5 76MH1-74E 11) Any vehicle which has been used for purposes other than what it was designed for. 12) Any damage or deterioration caused by industrial pollution and bird droppings. 13) Insignificant defects which do not affect the function of the vehicle including without limitation, sound, vibration and fluid seep. 14) Any natural wear and tear including without limitation, aging etc. 15) Installation and usage of domestic LPG gas/LPG Cylinder. 16) V-belts, hoses and gas leaks (For Maruti Suzuki AC vehicle). 17) Any vehicle retrofitted with LPG/CNG kits. (5) Extent of Warranty: This warranty is the entire written warranty given by Maruti Suzuki for Maruti Suzuki vehicles and no dealer or its or his agent or employee is authorised to extend or enlarge this warranty and no dealer or its or his agent or employee is authorised to make any oral warranty on Maruti Suzuki’s behalf. Maruti Suzuki reserves the right to add any improvements or change the design of any model at any time with no obligation to make the same changes on units previously sold. (6) Warranty Service: To obtain warranty service, the complete vehicle must be presented at the owner’s expenses to any authorised Maruti Suzuki dealer. – Have performed, at his own expenses, by an Maruti Suzuki authorised dealer/service station all the service inspections specified in the Maruti Suzuki “Owner’s Manual and Service Booklet and maintain adequate proof that such service inspections have been performed. – Make certain that the Maruti Suzuki authorised dealer/service station performing the service inspection has certified the work on the “Maintenance Service Record” page in the “Owner’s Manual and Service Booklet and – Present the Maruti Suzuki “Owner’s Manual and Service Booklet to the authorised Maruti Suzuki dealer whenever requesting service inspections or warranty service. If the “Owner’s Manual and Service Booklet should be lost or destroyed the owner should consult the authorised Maruti Suzuki dealer from whom the vehicle was purchased for instructions concerning replacement of the “Owner’s Manual and Service Booklet. (8) Disclaimer of Consequential Damage: Maruti Suzuki assumes no responsibility for loss of vehicle, loss of time, inconvenience or any other indirect incidental or consequential damage resulting from the vehicle not being available to the owner because of any defect covered by this warranty. (9) Change of Owner Even if ownership of the vehicle changes, the remaining warranty period is effective for the new owner. (7) Owner’s Warranty ResponsibIlities: It is responsibility of each owner to: – Make certain that the warranty registration/PDl card was completed at the time of delivery of the vehicle; 0-6 7 55KS0-74E 76MH1-74E EMISSION WARRANTY POLICY Maruti Suzuki offers the Emission Warranty on all Maruti Suzuki vehicles (apart from the Regular Warranty and will run parallel to the regular product warranty) only in four metropolitan cities (New Delhi, Kolkata, Mumbai and Chennai) with effect from July 1st, 2001. Terms: The Emission Warranty will be applicable for 80,000 kms or 3 years (Whichever comes earlier) from the date of delivery to the first owner. The remaining warranty terms will be valid in case of any change in ownership provided the production of all valid documents. Conditions: 1. Under Emission Waranty, Warranty claims will be admitted for a prima facie examination, in case vehicle fails to meet the Emission Standard as specified in sub rule (2) of rule no. 115 of Central Motor Vehicles Rules (CMVR), 1989. 2. The warranty claims will only be accepted after examination carried out by Maruti Suzuki or it’s dealer which leads to firm conclusions that the a) Original settings have not been tempered in any case. b) Part (as given in Annexure - A) has a manufacturing defect. c) Vehicle is unable to meet the Emission Standards (as given in 1.), inspite of the vehicle having been maintained and used in accordance with the instructions as specified in Owner’s Manual and Service Booklet and the used fuel and different oils (Engine oil, Transmission oil, Brake oil etc.) are also as per specification. 8 3. The method of examination for deciding the warranty of the parts will be at the sole discretion of Maruti Suzuki and it’s dealer and results of the examination will be final and binding. If after examination, the warrantable condition is not established, Maruti Suzuki and it’s dealer has the right to charge all, or part of the cost of such examination. 4. Under Emission Warranty, the parts (as given in Annexure - A) will be changed free of cost, but the consumables will be charged as per actual. 5. If the part covered under Emission Warranty or the associated parts, are not independently replaceable, on account of these being integral parts of a complete assembly, Maruti Suzuki and it’s dealer will have the sole discretion to replace either the entire assembly or by using some of the parts of the system through suitable repairs or modifications. 6. Any consequential repairs or replacement of parts which may be found necessary to establish compliance of Emission Warranty, will not be considered under warranty, unless the same is under product warranty. The consumable will be charged as per actual under such repair or replacement. 7. Maruti Suzuki will not be responsible for the cost of transportation of the vehicle to the nearest Maruti Suzuki dealer workshop or any loss due to non-availability of the vehicle during the period of lodging of a warranty claim and examination and/ or repair by Maruti Suzuki dealer. 8. Maruti Suzuki will not be responsible for any penalty that may be charged by statutory authorities on account of failure to comply with the EMISSION STANDARDS. 9. Emission Waranty will not be affected on the change of owner, provided all the documents are available. 0-7 76MH1-74E 10.All maintenance actions (as specified in the Owner’s Manual and Service Booklet) need to be followed and recorded in the manual for emission warranty. 11.The customer needs to produce the PUC (Pollution Under Control) certificate valid for the period preceeding the test during which the failure is discovered. The receipts (for the maintenance of the vehicle as per specification in Owner’s Manual and Service Booklet from the date of original purchase of the vehicle) will also be required. Conditions under which the Emission Warranty is not APPLICABLE 1. In the absence of valid PUC certificate. 2. Vehicle not serviced from Maruti Suzuki authorised workshop as per the schedule specified in the Owner’s Manual. 3. Vehicle subjected to abnormal use (accident, motor race, rallies or for the purpose of establishing the records etc). 4. Use of non MGP (Maruti Geniune Part). 5. Vehicle tampered in an unauthorised manner. 6. Tampering with odometer so that the actual kilometer reading can not be read. 7. Use of adulterated fuel and/or unspecified oils (Engine oil, Transmission oil and Brake oil etc). 0-8 Annexure - A List of parts covered under Emission Warranty 1. Fuel Injection Assembly, Pressure Regulator, Throttle Body Assembly. 2. Electronic Control Module (ECM). 3. Intake Manifold. 4. EGR valve. 5. Distributor and internal parts. 6. Ignition Coil. 7. Canister Assembly. 8. Vapour Liquid Seperator. 9. Fuel Tank and Filler Cap. 10. PCV (Positive Crankcase Ventilation) Valve. 11. Oil Filler Cap. 12. Catalytic Convertor. 13. Exhaust Manifold. 14. All Fuel Injection System related SENSORS. 15. High Pressure Fuel Pump. 16. Glow Plug. 17. Glow Plug Controller. 9 55KS0-74E FUEL RECOMMENDATION Fuel Recommendation Petrol Engine You must use unleaded petrol with an octane number (RON) of 91 or higher. Petrol/Ethanol blends Blends of unleaded petrol and ethanol (grain alcohol), also known as gasohol, are commercially available in some areas. Blends of this type may be used in your vehicle if they are no more than 10% ethanol. Make sure this petrol-ethanol blend has octane ratings no lower than those recommended for petrol. Petrol/Methanol blends Blends of unleaded petrol and methanol (wood alcohol) are also commercially available in some areas. DO NOT USE fuels containing more than 5% methanol under any circumstances. Fuel system damage or vehicle performance problems resulting from the use of such fuels are not the responsibility of MARUTI SUZUKI and may not be covered under the New Vehicle Warranty. Fuels containing 5% or less methanol may be suitable for use in your vehicle if they contain cosolvents and corrosion inhibitors. 1-1 76MH1-74E NOTE: If you are not satisfied with the driveability or fuel economy of your vehicle when you are using a petrol/alcohol blend, you should switch back to unleaded petrol containing no alcohol. NOTICE The fuel tank has an air space to allow for fuel expansion in hot weather. If you continue to add fuel after the filler nozzle has automatically shut off or an initial blowback occurs, the air chamber will become full. Exposure to heat when fully fuelled in this manner will result in leakage due to fuel expansion. To prevent such fuel leakage, stop filling after the filler nozzle has automatically shut off, or when using an alternative non-automatic system, initial vent blowback occurs. NOTICE Be careful not to spill fuel containing alcohol while refueling. If fuel is spilled on the vehicle body, wipe it up immediately. Fuels containing alcohol can cause paint damage, which is not covered under the New Vehicle Limited Warranty. Diesel Engine The diesel fuel should be with Cetane Number (CN) higher than 51 and sulfur content less than 350 ppm (parts per million). MARUTI SUZUKI recommends to use the diesel fuel conformable to EN590. Do not use marine diesel fuel, heating oils and so forth. NOTICE The fuel tank has an air space to allow for fuel expansion in hot weather. If you continue to add fuel after the filler nozzle has automatically shut off or an initial blow back occurs, the air chamber will become full. Exposure to heat when fully fuelled in this manner will result in leakage due to fuel expansion. To prevent such fuel leakage, stop filling after the filler nozzle has automatically shut off, or when using an alternative non-automatic system, initial vent blowback occurs. NOTICE Be careful not to spill fuel containing alcohol while refueling. If fuel is spilled on the vehicle body, wipe it up immediately. Fuels containing alcohol can cause paint damage, which is not covered under the New Vehicle Limited Warranty. 10 76MH1-74E 76MH1-74E BEFORE DRIVING Keys ...................................................................................... 2-1 Door Locks .......................................................................... 2-2 Keyless Entry System Transmitter (if equipped) ............. 2-5 Security System (if equipped) ............................................ 2-7 Windows .............................................................................. 2-10 Mirrors .................................................................................. 2-11 Front Seats .......................................................................... 2-13 Rear Seats ............................................................................ 2-13 Seat Belts and Child Restraint Systems ........................... 2-15 Supplemental Restraint System (air bags) (if equipped) ......................................................................... 2-23 Instrument Cluster .............................................................. 2-28 Speedometer ....................................................................... 2-29 Tachometer (if equipped) ................................................... 2-29 Brightness Control .............................................................. 2-29 Information Display ............................................................. 2-30 Fuel Gauge ........................................................................... 2-31 Warning and Indicator Lights ............................................ 2-37 Lighting Control Lever ........................................................ 2-42 Front Fog Light Switch (if equipped) ................................ 2-43 Headlight Leveling Switch .................................................. 2-43 Turn Signal Control Lever .................................................. 2-44 Hazard Warning Switch ...................................................... 2-45 Windshield Wiper and Washer Lever ................................ 2-45 Tilt Steering Lock Lever (if equipped) ............................... 2-47 Horn ...................................................................................... 2-47 Heated Rear Window Switch (if equipped) ....................... 2-47 11 76MH1-74E BEFORE DRIVING 76MH1-74E Keys Immobilizer System EXAMPLE 51KM024 Your vehicle comes with a pair of identical keys. Keep the spare key in a safe place. One key can open all of the locks on the vehicle. The key identification number is stamped on a metal tag provided with the keys or on the keys. Keep the tag (if equipped) in a safe place. If you lose your keys, you will need this number to have new keys made. Write the number below for your future reference. KEY NUMBER: This system is designed to help prevent vehicle theft by electronically disabling the engine starting system. The engine can be started only with your vehicle’s original immobilizer ignition key which has an electronic identification code programmed into it. The key communicates the identification code to the vehicle when the ignition switch is turned to the “ON” position. If you need to make spare keys, see your MARUTI SUZUKI dealer. The vehicle must be programmed with the correct identification code for the spare keys. A key made by an ordinary locksmith will not work. or with the immobilizer system. Ask your MARUTI SUZUKI dealer to inspect the system. NOTE: • If you lose your immobilizer ignition key, see your MARUTI SUZUKI dealer as soon as possible to have the lost one deactivated, then have the new key made by them. • If you own other vehicles with immobilizer keys, keep those keys away from the ignition switch when using your vehicle, or the engine may not be started because they may interfere with your vehicle’s immobilizer system. • If you attach any metal objects to the immobilizer key, it may not start the engine. NOTICE 80JM122 If the immobilizer system light blinks when the ignition switch is in the “ON” position, the engine will not start. NOTE: • If this light blinks, turn the ignition switch to the “LOCK” position, then turn it back to the “ON” position. • If the light still blinks with the ignition switch turned to the “ON” position, there may be something wrong with your key The immobilizer key is a sensitive electronic instrument. To avoid damaging the immobilizer key: • Do not expose it to impacts, moisture or high temperature such as on the dashboard under direct sunlight. • Keep the immobilizer key away from magnetic objects. Ignition Key Reminder (if equipped) A buzzer sounds intermittently to remind you to remove the ignition key if it is in the ignition switch when the driver’s door is opened. 12 2-1 76MH1-74E BEFORE DRIVING 76MH1-74E Door Locks To lock a front passenger’s door from outside the vehicle, turn the lock knob forward, then pull and hold the door handle as you close the door. Side Door Locks Driver’s door Central Door Locking System (if equipped) Driver’s door To lock a rear door from outside the vehicle, turn the lock knob forward and close the door. You do not need to hold the door handle up as you close the door. (1) (2) (1) (3) EXAMPLE (2) (3) Door Lock Knob (1) (2) (4) (4) 76MH0A002 76MH0A001 (1) (2) (3) (4) (1) (2) (3) (4) LOCK UNLOCK Front Rear To lock a driver’s door from outside the vehicle: • Insert the key and turn the top of the key toward the front of the vehicle, or • Turn the lock knob forward, then pull and hold the door handle as you close the door. To unlock a driver’s door from outside the vehicle, insert the key and turn the top of the key toward the rear of the vehicle. LOCK UNLOCK Front Rear 76MH0A019 You can lock and unlock all doors (including the tailgate) simultaneously by using the key in the driver’s door lock. To lock a door from inside the vehicle, turn the lock knob forward. Turn the lock knob backward to unlock the door. You do not need to pull and hold the door handle as you close the door. To lock all doors simultaneously, insert the key in the driver’s door lock and turn the top of the key toward the front of the vehicle once. (1) LOCK (2) UNLOCK To unlock all doors simultaneously, insert the key in a driver’s door lock and turn the top of the key toward the rear of the vehicle twice. 13 2-2 76MH1-74E BEFORE DRIVING 76MH1-74E Child-Proof Locks (rear door) NOTE: You can switch the function that unlocks all doors from twice operations to once operation, and vice versa, via the setting mode of the information display. For details on how to use the information display, refer to “Information Display” in this section. EXAMPLE (2) To unlock the driver’s door only, insert the key in that door lock and turn the top of the key toward the rear of the vehicle once. EXAMPLE (1) (2) (3) 76MH0A020 (1) LOCK (2) UNLOCK You can also lock or unlock all doors by depressing the front or rear of the switch (3), respectively. (1) NOTE: If your vehicle is equipped with keyless entry system, you can also lock or unlock all doors by operating the transmitter. Refer to “Keyless Entry System Transmitter” in this section. NOTE: • All doors are automatically unlocked when you turn the ignition switch to the “LOCK” position and pull out the key. • All doors are automatically locked for safety when the vehicle speed reaches 15 km/h. • You can change the automatic locking or unlocking function mentioned above via the setting mode of the information display. For details on how to use the information display, refer to “Information Display” in this section. 76MH0A021 (1) LOCK (2) UNLOCK Each of the rear doors is equipped with a child-proof lock which can be used to help prevent unwanted opening of the door from inside the vehicle. When the lock lever is in the “LOCK” position (1), the rear door can only be opened from outside. When the lock lever is in the “UNLOCK” position (2), the rear door can be opened from inside or outside. WARNING Be sure to place the child-proof lock in the “LOCK” position whenever children are seated in the rear. 14 2-3 76MH1-74E BEFORE DRIVING 76MH1-74E Tailgate WARNING Always make sure that the tailgate is closed and latched securely. Completely closing the tailgate helps prevent occupants from being thrown from the vehicle in the event of an accident. Completely closing it also helps keep exhaust gases from entering the vehicle. (2) (1) • If your vehicle is not equipped with the central door locking system, you can lock or unlock the tailgate by using the key in the tailgate lock (2). To open the tailgate, pull up the tailgate handle (3) and lift the tailgate. If you cannot unlatch the tailgate by pulling up the tailgate handle (3) due to a discharged battery or malfunction, follow the procedures below to unlatch the tailgate from inside the vehicle. 1) Remove the luggage compartment cover (if equipped) and fold the rear seat forward for easier access. Refer to “Folding Rear Seats” section for details on how to fold the rear seat forward. (6) (7) 76MH0A137 3) To unlock the tailgate lock, pull the lock plate (6) up. To open the tailgate, push the emergency lever (7) sideways. The tailgate will be latched again by simply closing the tailgate. If the tailgate cannot be unlatched by pulling up the tailgate handle (3), have the vehicle inspected by your MARUTI SUZUKI dealer. (5) (3) EXAMPLE CAUTION 76MH0A086 (1) Driver’s door lock (2) Tailgate lock (3) Tailgate handle • If your vehicle is equipped with the central door locking system, you can lock or unlock the tailgate by using the key in the driver’s door lock (1). (4) 76MH0A099 Make sure there is no one near the tailgate when pushing open the tailgate from inside the vehicle. To avoid injury, do not use your finger to push the emergency lever. 2) Remove the trim (5) of the tailgate. • Push center of the clips (4) and pull them out. Then, remove the trim (5). 15 2-4 76MH1-74E BEFORE DRIVING 76MH1-74E Keyless Entry System Transmitter (if equipped) The turn signal lights will flash once and the siren (if your vehicle is equipped with the security system) will sound once when the doors are locked. (1) (2) 76MS011 (1) “LOCK” button (2) “UNLOCK” button You can lock or unlock all doors (including the tailgate) simultaneously by operating the transmitter near the vehicle. • To lock all doors, push the “LOCK” button (1) once. • To unlock only the driver’s door, push the “UNLOCK” button (2) once. • To unlock other doors, push the “UNLOCK” button (2) once again. NOTE: You can switch the function that unlocks all doors from twice operations to once operation, and vice versa, via the setting mode of the information display. For details on how to use the information display, refer to “Information Display” in this section. When the doors are unlocked: • The turn signal lights will flash twice and the siren (if your vehicle is equipped with the security system) will sound twice. • If the interior light switch is in the “DOOR” position, the interior light will turn on for about 15 seconds and then fade out. If you insert the key into the ignition switch during this time, the light will start to fade out immediately. Be sure the doors are locked after you operate the “LOCK” button. If no door is opened within about 30 seconds after the “UNLOCK” button is operated, the doors will automatically lock again. NOTE: (For models with security system) • If you lock the doors using the transmitter when the engine hood is open, the siren will sound 3 times to remind you. • If the security system was triggered due to an unauthorized entry into the vehicle and then you unlock the doors using the transmitter, the siren will sound 4 times to remind you. If this happens, check whether your vehicle has been broken into while you were away from it. • Once you push both of the “LOCK” button (1) and “UNLOCK” button (2), then you push one of the buttons within 5 sec- onds, the siren will not sound. However, If you push one of the buttons twice within 5 seconds, or push one of the buttons 5 seconds later, the siren will sound. • You can set whether the siren sounds when locking or unlocking the door(s) via the setting mode of the information display. For details on how to use the information display, refer to “Information Display” in this section. NOTE: • The maximum operating distance of the keyless entry system transmitter is about 15 m (48 ft.), but this can vary depending on the surroundings, especially near other transmitting devices such as radio towers or CB (Citizen’s Band) radios. • The door locks cannot be operated with the transmitter if the ignition key is inserted in the ignition switch. • If any door is open, you cannot lock the door by operating the transmitter, however unlock the door. • If you lose one of the transmitters, ask your MARUTI SUZUKI dealer as soon as possible for a replacement. Be sure to have your dealer program the new transmitter code in your vehicle’s memory so that the old code is erased. 16 2-5 76MH1-74E BEFORE DRIVING 76MH1-74E NOTICE The transmitter is a sensitive electronic instrument. To avoid damaging the transmitter: • Do not expose it to impacts, moisture or high temperature such as by leaving it on the dashboard under direct sunlight. • Keep the transmitter away from magnetic objects such as a television. • Do not tamper with internal parts. Panic alarm function (if equipped) This function is to get the attention of others. Push both of the “LOCK” button (1) and “UNLOCK” button (2) for more than 3 seconds. The turn signal lights will blink for about 27.5 seconds. Also, the siren will sound for about 27.5 seconds at the same time. To cancel the panic alarm, press any button (LOCK or UNLOCK). You can also turn the ignition switch to the “ON” position to cancel the panic alarm. Replacement of the Battery If the transmitter becomes unreliable, replace the battery. To replace the battery of the transmitter: (1) (2) 68LM248 1) Remove the screw (1), and open the transmitter cover. 2) Remove the transmitter (2). (2) 3) Put the edge of a flat blade screwdriver in the slot of the transmitter (2) and pry it open. 4) Replace the battery (3) so its + terminal faces the “+” mark of the transmitter. 5) Close the transmitter and install it into the transmitter holder. 6) Close the transmitter cover, install and tighten the screw (1). 7) Make sure the door locks can be operated with the transmitter. 8) Dispose of the used battery properly according to applicable rules or regulations. Do not dispose of lithium batteries with ordinary household trash. WARNING Swallowing a lithium battery may cause serious internal injury. Do not allow anyone to swallow a lithium battery. Keep lithium batteries away from children and pets. If swallowed, contact a physician immediately. NOTICE The transmitter is a sensitive electronic instrument. To avoid damaging it, do not expose it to dust or moisture or tamper with internal parts. (3) NOTE: The panic alarm function will not activate when the key is in the ignition switch. 68LM249 (3) Lithium disc type battery: CR1616 or equivalent 17 2-6 76MH1-74E BEFORE DRIVING Security System (if equipped) The security system is armed in about 5 seconds after you lock all doors (including the tailgate) by using the keyless entry system transmitter. Once the system is armed, any attempt to open a door by using any other means (*) than the keyless entry system transmitter, or open the engine hood, will cause the alarm to be triggered. * These means include the following: – The key – The lock knob on a door – The central door locking switch Also, in case that you have set the shock sensor to enabled state and set sensitivity of the pre-warning function and full blast warning function to a level other than 0, the alarm will be triggered if any attempt to tamper with the vehicle. The shock sensor can be selected enabled or disabled state, and sensitivity of each warning can be adjusted as desired. To set the shock sensor, ask your MARUTI SUZUKI dealer or use the setting mode of the information display. 76MH1-74E NOTE: • The default setting of the shock sensor is in the disabled state. Set to the enabled state and adjust sensitivity of each warning according to your preference. For details on how to use the information display, refer to “Information Display” in this section. • Your dealer may have already set the shock sensor of the vehicle to the enabled state before you purchase it. Consult your dealer for further information. NOTE: • The security system generates alarms when any of the predetermined conditions is met. However, the system does not have any function of blocking unauthorized entry into the vehicle. • Always use the keyless entry system transmitter to unlock the doors when the security system has been armed. Using a key instead will trigger the alarm. • If a person who does not know the security system is going to drive the vehicle, we recommend you explain the system and its operation to the person, or disable the system beforehand. Mistakenly triggering the alarm may cause a nuisance to others. • Even if the security system is armed, you should still be careful to guard against theft. Do not leave money or things of value in the vehicle. How to arm the security system (when enabled) Lock all doors (including the tailgate) using the keyless entry system transmitter. The security system indicator (1) will start blinking rapidly, and the security system will be armed in about 5 seconds. While the system is being armed, the indicator continues to blink at intervals of approximately 2 seconds. With tachometer (1) 76MH0B001 18 2-7 76MH1-74E BEFORE DRIVING 76MH1-74E armed in about 5 seconds if the system is in the enabled state. • If the security system indicator (1) blinks when the ignition switch is in the “ON” position, there may be something wrong with the security system. Ask your MARUTI SUZUKI dealer to inspect the system. Without tachometer (1) How to disarm the security system Simply unlock the doors using the keyless entry system transmitter. The security system indicator will go out, indicating that the security system is disarmed. 76MH0B002 NOTE: • To prevent the alarm from being accidentally triggered, avoid arming it while anyone remains inside the vehicle. The alarm will be triggered if any person inside opens the door or engine hood, or swings the vehicle (if the shock sensor is in the enabled state). • The security system is not armed when all doors are locked using the key from outside, or using the door lock knobs or the central door locking switch from inside. • If any door is not operated within approximately 30 seconds after the doors have been unlocked using the keyless entry system transmitter, the doors are automatically locked again. When the doors are locked, the security system will be How to stop the alarm Should the alarm be triggered accidentally, unlock the doors using the keyless entry system transmitter, or insert the key in the ignition switch and turn it to “ON” position. The alarm will then stop. NOTE: • Even after the alarm has stopped, if you lock the doors using the keyless entry system transmitter, the security system will be rearmed with a delay of about 5 seconds. • If you disconnect the battery while the security system is in the armed condition or the alarm is actually in operation, the alarm will be re-triggered when the battery is then reconnected. • Even after the alarm has stopped at the end of the predetermined operation time, it will be triggered again if any of the doors or engine hood is opened, or the vehicle feels a shock (if the shock sensor is in the enabled state), without disarming the security system. Checking whether the alarm has been triggered during parking If the alarm was triggered and you then turn the ignition switch to “ON” position, the security system indicator will blink rapidly for about 8 seconds and a buzzer will beep 4 times during this period. If this happens, check whether the vehicle has been broken into while you were away from it. Enabling and disabling the security system The security system can be either enabled or disabled. When enabled • If any of the doors are opened without unlocking by the keyless entry system transmitter, all turn signal lights start to blink and the interior buzzer beeps intermittently. After 5 seconds, the siren will sound for about 27.5 seconds. The security system indicator continues to blink during this time. • If the engine hood is opened, all turn signal lights blink, and the siren sounds for about 27.5 seconds. The security system indicator continues to blink during this time. (If the shock sensor is in the enabled state) • If the vehicle feels a shock, the siren sounds for about 2 seconds (pre-warning). If the vehicle continues to feel a 19 2-8 76MH1-74E BEFORE DRIVING 76MH1-74E shock, all turn signal lights start to blink and the interior buzzer beeps intermittently. After 5 seconds, the siren will sound for about 27.5 seconds (full blast warning). The security system indicator continues to blink during this time. EXAMPLE (1) NOTE: If you set the full blast warning sensitivity higher than the pre-warning sensitivity in the setting mode of the information display, or the vehicle feels such shock as to be able to trigger the full blast warning, the full blast warning will be triggered preferentially. In this case, the pre-warning will not be triggered. When disabled When the system is disabled, it stays disarmed even if you perform any system arming operation. How to switch the state of the security system When the security system has been already disarmed, you can switch the system from the enabled state to the disabled state, and vice versa, using the following method. 1) Sit in the driver’s seat and make sure that all doors are closed, and then turn the ignition switch to “ON” position. • If any door is open, the open door warning light comes on. (2) NOTE: The following steps 3) and 4) must be completed within 15 seconds. EXAMPLE 4 times 76MH0B003 OFF 76MH0B005 EXAMPLE 3) Turn the knob on the lighting control lever to the position and then turn back to the OFF position. Repeat this operation 4 times. EXAMPLE (3) (4) 3 times (6) 76MH0B004 2) Turn the lock knob (1) on the driver’s door rearward (2). Turn the knob on the lightning control lever to the OFF position (3). (5) 76MH0B006 20 2-9 76MH1-74E BEFORE DRIVING 76MH1-74E 4) Push the lock end (4) (forward end) of the central door locking switch (5), and then push the unlock end (6) (backward end). Repeat this operation 3 times. Every time you perform the series of the above steps, the state of the security system changes from the currently selected one to the other. You can check whether the system is enabled or disabled by the number of interior buzzer beeps at the end of the procedure as follows. System state Number of beeps Disabled Once Windows 76MH0A022 The driver’s door has a switch (1) to operate the driver’s window, and a switch (2) to operate the front passenger’s window or there are switches (4), (3), to operate the rear left and right passenger windows, respectively. Manual Window Control (if equipped) EXAMPLE Passenger’s door (5) EXAMPLE 60G010 Enabled 4 times • If you cannot complete the operations in step 3) and 4) within 15 seconds correctly, the state of the security system will not change and the interior buzzer does not beep. Perform the procedure again from the beginning. NOTE: You can also switch the security system from the enabled state to the disabled state, and vice versa, via the setting mode of the information display. For details on how to use the information display, refer to “Information Display” in this section. Raise or lower the door windows by turning the handle located on the door panel. Electric Window Controls (if equipped) The electric windows can only be operated when the ignition switch is in the “ON” position. Driver’s door 76MH0A023 The passenger’s door has a switch (5) to operate that passenger’s window. CLOSE EXAMPLE (2) (1) (3) OPEN (4) 81A009 21 2-10 76MH1-74E BEFORE DRIVING 76MH1-74E To open a window, push the top part of the switch and to close the window, lift up the top part of the switch. The driver’s window has an “auto-down” feature for added convenience (at toll booths or drivethrough restaurants, for example). This means you can open the window without holding the window switch in the “Down” position. Press the driver’s window switch completely down and release it. To stop the window before it reaches the bottom, pull the switch up briefly. Lock switch EXAMPLE 76MH0A024 The driver’s door also has a lock switch for the passenger’s windows. When you push in the lock switch, the passenger’s windows cannot be raised or lowered by operating any of the switches (1), (2), (3) or (4). To restore normal operation, release the lock switch by pushing again. WARNING • You should always lock the passenger’s window operation when there are children in the vehicle. Children can be seriously injured if they get part of their body caught by the window during operation. • To avoid injuring an occupant by window entrapment, be sure no part of the occupant’s body such as hands or head is in the path of the electric windows when closing them. • Always remove the ignition key when leaving the vehicle even if only for a short time. Also do not leave children alone in a parked vehicle. Unattended children could use the electric window switches and get trapped by the window. Mirrors Inside Rearview Mirror You can adjust the inside rearview mirror by hand so as to see the rear of your vehicle in the mirror. Type 1 74LHT0235 Type 2 NOTE: If you drive with one of the rear windows open, you may hear a loud sound caused by air vibration. To reduce the sound, open the driver’s or front passenger’s window, or narrow the rear window opening. 68LMT0205 (1) (2) (3) 68LMT0206 (2) Day driving (3) Night driving 22 2-11 76MH1-74E BEFORE DRIVING 76MH1-74E To adjust the mirror, set the selector tab (1) to the day position, then move the mirror up, down or sideways by hand to obtain the best view. Electric Mirrors (if equipped) Type 1 EXAMPLE (1) EXAMPLE When driving at night, you can move the selector tab to the night position to reduce glare from the headlights of vehicles behind you. (3) (2) (4) (1) Outside Rearview Mirrors (2) Adjust the outside rearview mirrors so you can just see the side of your vehicle in the mirrors. (4) WARNING Be careful when judging the size or distance of a vehicle or other object seen in the side convex mirror. Be aware that objects look smaller and appear farther away than when seen in a flat mirror. (3) 76MH0A025 Type 2 EXAMPLE (1) 68KH009 76MH0A026 The switch to control the electric mirrors is located on the driver’s door panel. You can adjust the mirrors when the ignition switch is in the “ACC” or “ON” position. To adjust the mirrors: 1) Move the selector switch to the left or right to select the mirror you wish to adjust. 2) Press the outer part of the switch that corresponds to the direction in which you wish to move the mirror. 3) Return the selector switch to the center position to help prevent unintended adjustment. You can adjust the outside rear view mirrors by hand with the knob (1) located on the driver’s or front passenger’s door panel. 23 2-12 76MH1-74E BEFORE DRIVING Front Seats Seat Adjustment 76MH1-74E Rear Seats EXAMPLE Folding Rear Seats The rear seat(s) of your vehicle can be folded forward to provide additional cargo space. WARNING Never attempt to adjust the driver’s seat or seatback while driving. The seat or seatback could move unexpectedly, causing loss of control. Make sure that the driver’s seat and seatback are properly adjusted before you start driving. To fold the rear seats forward: EXAMPLE WARNING To avoid excessive seat belt slack, which reduces the effectiveness of the seat belts as a safety device, make sure that the seats are adjusted before the seat belts are fastened. (1) (2) (3) (1) 76MH0A027 Seat position adjustment lever (1) Pull the lever up and slide the seat. 76MH0A028 WARNING All seatbacks should always be in an upright position when driving, or seat belt effectiveness may be reduced. Seat belts are designed to offer maximum protection when seatbacks are in the upright position. Seatback angle adjustment lever (2) Pull the lever up and move the seatback. Seat height adjustment lever (3) (if equipped) Pull the lever up to raise the seat. Push the lever down to lower the seat. After adjustment, try to move the seat and seatback forward and rearward to ensure that it is securely latched. 1) Insert the latch plate of the outboard lap-shoulder belts into the slit (1). NOTICE • When you move a seatback, make sure the latch plate is inserted into the slit securely so the seat belts are not caught by the seatback, seat hinge, or seat latch. This helps prevent damage to the belt system. • Make sure the belt webbing is not twisted. 24 2-13 76MH1-74E BEFORE DRIVING 76MH1-74E To return the seat to the normal position, follow the procedure below. After returning the seat, try moving the seatback to make sure they are securely latched. WARNING When returning the rear seatback to the normal position, make sure that there is nothing around the striker. Any foreign materials prevent the seatback from being locked securely. CAUTION Do not put your hand into the rear seatback lock opening, or your finger may get caught and be injured. NOTICE CAUTION EXAMPLE 76MH0A029 2) Pull up the release straps on the top of the seat(s), and fold the seatback forward. When returning the rear seatback to the normal position, be careful that your finger is not caught between the lock and the striker. NOTICE After folding the rear seatback forward, do not allow any foreign material to enter the lock opening. This may cause damage to the inside of the lock and prevent the seatback from being locked securely. WARNING If you need to carry cargo in the passenger compartment with the rear seat back folded forward, be sure to secure the cargo or it may be thrown about, causing injury. Never pile cargo higher than the seatback. 25 EXAMPLE • When returning the rear seatback to the normal position, do not allow any foreign material to enter the lock opening. This may prevent the seatback from being locked securely. • When returning the rear seatback to the normal position, be sure to handle it carefully by hand to avoid any damage to the lock itself. Do not push it by using some material or by applying excessive force. • As the lock is designed exclusively for securing the rear seatback, do not use it for any other purpose. Incorrect use of it may cause damage to the inside of the lock and prevent the seatback from being locked securely. 76MH0A030 Raise the seatback until it locks into place. 2-14 76MH1-74E BEFORE DRIVING 76MH1-74E Seat Belts and Child Restraint Systems Above the pelvis Across the pelvis 65D606 65D231S WARNING Wear Your Seat Belts at All Times. WARNING An air bag supplements, or adds to, the frontal crash protection offered by seat belts. The driver and all passengers must be properly restrained by wearing seat belts at all times, whether or not an air bag is mounted at their seating position, to minimize the risk of severe injury or death in the event of a crash. WARNING • Never allow persons to ride in the cargo area of a vehicle. In the event of an accident, there is a much greater risk of injury for persons who are not riding in a seat with their seat belt securely fastened. • Seat belts should always be adjusted as follows: – the lap portion of the belt should be worn low across the pelvis, not across the waist. – the shoulder straps should be worn on the outside shoulder only, and never under the arm. – the shoulder straps should be away from your face and neck, but not falling off your shoulder. (Continued) 65D201 WARNING (Continued) • Seat belts should never be worn with the straps twisted and should be adjusted as tightly as is comfortable to provide the protection for which they have been designed. A slack belt will provide less protection than one which is snug. • Make sure that each seat belt buckle is inserted into the proper buckle catch. It is possible to cross the buckles in the rear seat. (Continued) 26 2-15 76MH1-74E BEFORE DRIVING 76MH1-74E WARNING as low as possible across the hips 65D199 WARNING (Continued) • Pregnant women should use seat belts, although specific recommendations about driving should be made by the woman’s medical advisor. Remember that the lap portion of the belt should be worn as low as possible across the hips, as shown in the diagram. • Do not wear your seat belt over hard or breakable objects in your pockets or on your clothing. If an accident occurs, objects such as glasses, pens, etc. under the seat belt can cause injury. (Continued) (Continued) • Never use the same seat belt on more than one occupant and never attach a seat belt over an infant or child being held on an occupant’s lap. Such seat belt use could cause serious injury in the event of an accident. • Periodically inspect seat belt assemblies for excessive wear and damage. Seat belts should be replaced if webbing becomes frayed, contaminated, or damaged in any way. It is essential to replace the entire seat belt assembly after it has been worn in a severe impact, even if damage to the assembly is not obvious. • Children age 12 and under should ride properly restrained in the rear seat. • Infants and small children should never be transported unless they are properly restrained. Restraint systems for infants and small children can be purchased locally and should be used. Make sure that the system you purchase meets applicable safety standards. Read and follow all the directions provided by the manufacturer. • For children, if the shoulder belt irritates the neck or face, move the child closer to the center of the vehicle. (Continued) WARNING (Continued) • Avoid contamination of seat belt webbing by polishes, oils, chemicals, and particularly battery acid. Cleaning may safely be carried out using mild soap and water. • Do not insert any items such as coins, clips, etc. into the seat belt buckles, and be careful not to spill liquids into these parts. If foreign materials get into a seat belt buckle, the seat belt may not work properly. • All seatbacks should always be in an upright position when driving, or seat belt effectiveness may be reduced. Seat belts are designed to offer maximum protection when seatbacks are in the upright position. Lap-Shoulder Belt Emergency Locking Retractor (ELR) The seat belt has an emergency locking retractor (ELR), which is designed to lock the seat belt only during a sudden stop or impact. It also may lock if you pull the belt across your body very quickly. If this happens, let the belt go back to unlock it, then pull the belt across your body more slowly. 27 2-16 76MH1-74E BEFORE DRIVING 76MH1-74E of the diagonal shoulder strap adjusts itself to allow freedom of movement. Safety reminder Sit up straight and fully back All Seat Belts Except Rear Center All seat belts except rear center are the lap-shoulder belt. Low on hips Rear Center Seat Belt Rear center seat belt is the lap belt. To fasten the belt, pull the latch plate attached to the seat belt across your hips and press it straight into the buckle until you hear a “click”. To reduce the risk of sliding under the belt during a collision, position the belt across your lap as low on your hips as possible and adjust it to a snug fit. 60A038 Low on hips To unfasten the seat belt, push the button on the buckle and retract the belt slowly while attaching a hand to the belt or/and the latch plate. 60A036 TO TIGHTEN To fasten the seat belt, sit up straight and well back in the seat, pull the latch plate attached to the seat belt across your body and press it straight into the buckle until you hear a “click”. Low on hips 60A040 To reduce the risk of sliding under the belt during a collision, position the lap portion of the belt across your lap as low on your hips as possible and adjust it to a snug fit by pulling the shoulder portion of the belt upward through the latch plate. The length 80JS028 To tighten the belt, pull the free end of the belt across alongside the lap strap. 60A039 28 2-17 76MH1-74E BEFORE DRIVING 76MH1-74E TO LOOSEN NOTE: To identify the center seat belt buckle and latch plate in the rear seat, “CENTER” is marked on the buckle and latch plate of the center lap belt. The buckles are designed so a latch plate cannot be inserted into the wrong buckle. Without tachometer EXAMPLE Driver’s Seat Belt Reminder (if equipped) With tachometer EXAMPLE Right angle 80JS029 76MS013 To lengthen, release the latch plate from the buckle, pull the latch plate (adjuster) in the direction of the arrow, at right angles to the belt. The latch plate should then be refitted into the buckle and the belt tightened as previously described. When the driver doesn’t buckle his or her seat belt with the ignition switch in the “ON” position, the driver’s seat belt reminder light in the instrument cluster will blink until the driver’s seat belt is buckled. To unfasten the belt, press the release button on the buckle catch. WARNING 76MH028 It is absolutely essential that the driver and passengers wear their seat belts at all times. Persons who are not wearing seat belts have a much greater risk of injury if an accident occurs. Make a regular habit of buckling your seat belt before putting the key in the ignition. 80JS031 29 2-18 76MH1-74E BEFORE DRIVING 76MH1-74E Seat Belt Hanger Seat Belt Inspection EXAMPLE Child Restraint Systems EXAMPLE (1) 76MH0A028 NOTICE • When you move a seatback, make sure the latch plate is inserted into the slit (1) securely so the seat belts are not caught by the seatback, seat hinge, or seat latch. This helps prevent damage to the belt system. • Make sure the belt webbing is not twisted. 65D209S Periodically inspect the seat belts to make sure they work properly and are not damaged. Check the webbing, buckles, latch plates, retractors, anchorages, and guide loops. Replace any seat belts which do not work properly or are damaged. 60G332S Infant restraint EXAMPLE WARNING Be sure to inspect all seat belt assemblies after any collision. Any seat belt assembly which was in use during a collision (other than a very minor one) should be replaced, even if damage to the assembly is not obvious. Any seat belt assembly which was not in use during a collision should be replaced if it does not function properly or it is damaged in any way was activated. 79J221 30 2-19 76MH1-74E BEFORE DRIVING 76MH1-74E Child restraint EXAMPLE able; make sure that the restraint system you select meets applicable safety standards. All child restraint systems are designed to be secured on vehicle seats by either seat belts (lap belts or the lap portion of lapshoulder belts). Whenever possible, MARUTI SUZUKI recommends that child restraint systems be installed on the rear seat. According to accident statistics, children are safer when properly restrained in rear seating positions than in front seating positions. 79J222 Booster seat EXAMPLE If you must use a front-facing child restraint in the front passenger’s seat, adjust the passenger’s seat as far back as possible. NOTE: Observe any statutory regulation about child restraints. WARNING If your vehicle is equipped with a front passenger air bag, do not install a rear-facing child restraint in the front passenger’s seat. If the passenger’s air bag inflates, a child in a rearfacing child restraint could be killed or seriously injured. The back of a rear-facing child restraint would be too close to the inflating air bag. WARNING If you install a child restraint system in the rear seat, slide the front seat far enough forward so that the child’s feet do not touch the front seatback. This will help avoid injury to the child in the event of an accident. 79J223 MARUTI SUZUKI highly recommends that you use a child restraint system to restrain infants and small children. Many different types of child restraint systems are avail- 65D608 58MS030 31 2-20 76MH1-74E BEFORE DRIVING 76MH1-74E Installation with Lap-Shoulder Seat Belts Try to move the child restraint system in all directions to make sure it is securely installed. NOTICE Before installing a child restraint system in the rear seat, raise the head restraint (if equipped) to the most upper position. ELR type belt 65D609 EXAMPLE WARNING Children could be endangered in a crash if their child restraints are not properly secured in the vehicle. When installing a child restraint system, be sure to follow the instructions below. Be sure to secure the child in the restraint system according to the manufacturer’s instructions. 80JC021 Install your child restraint system according to the instructions provided by the child restraint system manufacturer. Make sure that the seat belt is securely latched. 32 2-21 76MH1-74E BEFORE DRIVING 76MH1-74E Child Restraint System for India Child Restraint The suitability of each passenger’s seat position for carriage of children and fitting of child restraint system is shown in the table below. Whenever you carry children up to 12 years of age, properly use the child restraints which conform to AIS 072, the standard for child restraints, referring to the table. Seating position (or other site) Front Passenger Rear Outboard Rear Centre Intermediate Outboard Intermediate Centre Group 0 Up to 10 kg X U X N.A. N.A. Group 0+ Up to 13 kg X U X N.A. N.A. Group I 9 to 18 kg X U X N.A. N.A. Group II 15 to 25 kg X U X N.A. N.A. Group III 22 to 36 kg X U X N.A. N.A. MASS GROUP Key of letters to be inserted in the above table: U =Suitable for ‘universal’ category restraints approved for use in this mass group X =Seat position not suitable for children in this mass group N.A = Seat position not available for children in this mass group. NOTE: ‘universal’ is the category in the AIS 072. 33 2-22 76MH1-74E BEFORE DRIVING 76MH1-74E Supplemental Restraint System (air bags) (if equipped) ing components in addition to a lap-shoulder belt at each front seating position. EXAMPLE 1. Driver’s front air bag module (if equipped) 2. Front passenger’s front air bag module (if equipped) 3. Air bag controller (if equipped) 4. Forward crash sensor (if equipped) EXAMPLE 2 Air bag symbol (if equipped) meaning 1 WARNING 4 3 An air bag supplements, or adds to, the crash protection offered by seat belts. The driver and all passengers must be properly restrained by wearing seat belts at all times, whether or not an air bag is mounted at their seating position, to minimize the risk of severe injury or death in the event of a crash. “AIR BAG” light (if equipped) WARNING This section of the owner’s manual describes the protection provided by your MARUTI SUZUKI’s SUPPLEMENTAL RESTRAINT SYSTEM (air bags). Please read and follow ALL these instructions carefully to minimize your risk of severe injury or death in the event of a collision. Your vehicle is equipped with a Supplemental Restraint System consisting of the follow- 72M00150 You may find this label on the sun visor. WARNING NEVER use a rearward facing child restraint on a seat protected by an ACTIVE AIRBAG in front of it, DEATH or SERIOUS INJURY to the CHILD can occur. Front Air Bags (if equipped) EXAMPLE 63J030 If the “AIR BAG” light on the instrument cluster does not blink or come on when the ignition switch is first turned to the “ON” position, or the “AIR BAG” light stays on, or comes on while driving, the air bag system may not work properly. Have the air bag system inspected by an authorized MARUTI SUZUKI dealer as soon as possible. 63J259 2-23 34 76MH1-74E BEFORE DRIVING 76MH1-74E Front air bags are designed to inflate in severe frontal collisions when the ignition switch is in the “ON” position. Front air bags are not designed to inflate in rear impacts, side impacts, rollovers or minor frontal collisions, since they would offer no protection in those types of accidents. Remember, since an air bag deploys only one time during an accident, seat belts are needed to restrain occupants from further movements during the accident. Therefore, an air bag is NOT a substitute for seat belts. To maximize your protection, ALWAYS WEAR YOUR SEAT BELTS. Be aware that no system can prevent all possible injuries that may occur in an accident. Driver’s front air bag (if equipped) EXAMPLE Front passenger’s front air bag (if equipped) WARNING EXAMPLE 76MH0A034 Do not install a rear-facing child restraint in the front passenger’s seat. If the passenger’s front air bag inflates, a child in a rear-facing child restraint could be killed or severely injured. The back of a rear-facing child restraint would be too close to the inflating air bag. Please refer to the “Seat Belts and Child Restraint Systems” section in this section for details on securing your child. Conditions of front air bags deployment (inflation) The driver’s front air bag is located behind the center pad of the steering wheel and the front passenger’s front air bag is located behind the passenger’s side of the dashboard. The words “SRS AIRBAG” are molded into the air bag covers to identify the location of the air bags. 80J097 • In frontal collisions with a fixed wall that does not move or deform in more than about 25 km/h (15 mph) (1) 76MH0A033 (1) 58MS030 35 2-24 76MH1-74E BEFORE DRIVING 76MH1-74E • In collisions such as above at an angle of about 30 degrees (1) or less from the front • Landing hard or falling Front air bags may inflate in a strong impact collision angle was greater than about 30 degrees from the front. Conditions of front air bags may inflate Receiving a strong impact to the lower body of your vehicle, the front air bags will inflate in many cases. 80J102 80J120 • Approximately 50 km/h (30 mph) or lower speed frontal collision to a stopped vehicle • Collision from the rear 80J099 • Hitting a curb or medial strip 80J119 • Collision from the side 80J103 • Collision that the front of your vehicle goes under the bed of a truck etc. 80J100E • Falling into a deep hole or ditch 80J110 • Vehicle rollover Front air bags may not inflate The front air bags may not inflate when the impact is absorbed since the collision object moved, vehicle body deformed, or 80J104 • Collision with a utility pole or stumpage 36 2-25 76MH1-74E BEFORE DRIVING 76MH1-74E How the system works (1) 80J105E • Collision with a fixed wall or guardrail at an angle of greater than about 30 degrees (1) from the front 80J106 • In frontal collisions with a fixed wall that does not move or deform in less than about 25 km/h (15 mph) 80J107 • Collision angle is offset from the vehicle angle (offset collision) In a frontal collision, the crash sensors will detect rapid deceleration, and if the controller judges that the deceleration represents a severe frontal crash, the controller will trigger the inflators. The inflators inflate the air bags with nitrogen or argon gas. The inflated air bags provide a cushion for your head and upper body. The air bag inflates and deflates so quickly that you may not even realize that it has activated. The air bag will neither hinder your view nor make it harder to exit the vehicle. Air bags must inflate quickly and forcefully in order to reduce the chance of serious or fatal injuries. However, an unavoidable consequence of the quick inflation is that the air bag may irritate bare skin, such as the facial area. Also, upon inflation, a loud noise will occur and some powder and smoke will be released. These conditions are not harmful and do not indicate a fire in the vehicle. Be aware, however, that some air bag components may be hot for a while after inflation. A seat belt helps keep you in the proper position for maximum protection when an air bag inflates. Adjust your seat as far back as possible while still maintaining control of the vehicle. Sit fully back in your seat; sit up straight; do not lean over the steering wheel or dashboard. Please refer to the “Front Seat” section and the “Seat Belts and Child Restraint Systems” section in this section for details on proper seat and seat belt adjustments. 65D610 WARNING • The driver should not lean over the steering wheel. The front passenger should not rest his or her body against the dashboard, or otherwise get too close to the dashboard. In these situations, the outof-position occupant would be too close to an inflating air bag, and may suffer severe injury. • Do not attach any objects to, or place any objects over, the steering wheel or dashboard. Do not place any objects between the air bag and the driver or front passenger. These objects may interfere with air bag operation or may be propelled by the air bag in the event of a crash. Either of these conditions may cause severe injury. 37 2-26 76MH1-74E BEFORE DRIVING Note that even though your vehicle may be moderately damaged in a frontal collision, the collision may not have been severe enough to trigger the air bags to inflate. If your vehicle sustains ANY front-end damage, have the air bag system inspected by an authorized MARUTI SUZUKI dealer to ensure it is in proper working order. Your vehicle is equipped with a diagnostic module which records information about the air bag system if the air bags deploy in a crash. The module records information about overall system status, which sensors activated the deployment, and for a certain vehicle only, whether the driver’s seat belt was in use. Servicing the air bag system If the air bags inflate, have the air bags and related components replaced by an authorized MARUTI SUZUKI dealer as soon as possible. If your vehicle ever gets in deep water and the driver’s floor is submerged, the air bag controller could be damaged. If it does, have the air bag system inspected by the MARUTI SUZUKI dealer as soon as possible. 76MH1-74E one who services your vehicle that it has air bags. Service on or around air bag components or wiring must be performed only by an authorized MARUTI SUZUKI dealer. Improper service could result in unintended air bag deployment or could render the air bag inoperative. Either of these two conditions may result in severe injury. To prevent damage or unintended inflation of the air bag system, be sure the battery is disconnected and the ignition switch has been in the “LOCK” position for at least 90 seconds before performing any electrical service work on your vehicle. Do not touch air bag system components or wires. The wires are wrapped with yellow tape or yellow tubing, and the couplers are yellow for easy identification. Scrapping a vehicle that has an uninflated air bag can be hazardous. Ask your dealer, body repair shop or scrap yard for help with disposal. Special procedures are required for servicing or replacing an air bag. For that reason, only an authorized MARUTI SUZUKI dealer should be allowed to service or replace your air bags. Please remind any38 2-27 76MH1-74E BEFORE DRIVING Instrument Cluster 1. 2. 3. 4. 5. 6. Speedometer Tachometer (if equipped) Information display Trip meter selector knob Indicator selector knob Warning and indicator lights With tachometer 4 6 1 6 5 For Diesel 2 2 6 3 EXAMPLE Without tachometer 4 6 1 6 3 5 EXAMPLE 39 2-28 76MH1-74E BEFORE DRIVING 76MH1-74E Speedometer Refer to “Low Fuel Warning Light” in “Warning and Indicator Lights” in this section for details. Without tachometer (2) The speedometer indicates vehicle speed. Tachometer (if equipped) The tachometer indicates engine speed in revolutions per minute. (1) The mark (2) indicates that the fuel filler door is located on the left side of the vehicle. Brightness Control NOTICE Never drive the vehicle with the engine revving in the red zone, or severe engine damage can result. Keep the engine speed below the red zone even when downshifting to a lower gear position. Refer to “Downshifting maximum allowable speeds” in the “OPERATING YOUR VEHICLE” section. Fuel Gauge EXAMPLE EXAMPLE (1) 76MH0A038 When the ignition switch is in the “ON” position, this gauge gives an approximate indication of the amount of fuel in the fuel tank. “F” stands for full and “E” stands for empty. If the fuel meter indicator shows only one segment to “E”, refill the tank as soon as possible. With tachometer NOTE: If the last segment blinks, it means that the fuel is almost empty. (1) (2) If the low fuel warning light (1) comes on, fill the fuel tank immediately. EXAMPLE NOTE: The activation point of the low fuel warning light (1) varies depending on road conditions (for example, slope or curve) and driving conditions because of fuel moving in the tank. 76MH0A037 76MH0A039 When the ignition switch is turned to the “ON” position, the pointer lights come on. Your vehicle has a system to automatically dim the brightness of the instrument panel lights when the position lights or headlights are on. When the position lights and/or headlights are ON, you can control the meter illumination intensity. 40 2-29 76MH1-74E BEFORE DRIVING 76MH1-74E To increase the brightness of the instrument panel lights, turn the brightness control knob (1) clockwise. To reduce the brightness of the instrument panel lights, turn the brightness control knob (1) counterclockwise. Information Display without tachometer EXAMPLE EXAMPLE (1) (2) WARNING (A) If you attempt to adjust the display while driving, you could lose control of the vehicle. Do not attempt to adjust the display while driving. NOTE: • If you do not turn the brightness control knob within about 5 seconds of activating the brightness control display, the brightness control display will be canceled automatically. • When you reconnect the battery, the brightness of the instrument panel lights will be reinitialized. Readjust the brightness according to your preference. (C) (B) (3) 76MH0A041 76MH0A032 with tachometer EXAMPLE (1) Trip meter selector knob (2) Indicator selector knob (3) Information display When the ignition switch is in the “ON” position, the information display shows the following information. Display (A) Clock (B) (D) Display (B) Fuel gauge (C) (A) (E) (3) 76MH0A040 Display (C) Trip meter / Odometer / Fuel consumption / Driving range Display (D) Gear position indicator (for Auto Gear Shift models) Display (E) Thermometer (if equipped) 41 2-30 76MH1-74E BEFORE DRIVING 76MH1-74E Fuel Gauge Clock When the ignition switch is in the “ON” position, the display (A) shows the time. To change the time indication: 1) Push the trip meter selector knob (1) and the indicator selector knob (2) together. 2) To change the hour indication, turn the indicator selector knob (2) left or right repeatedly when the hour indication blinks. To change the hour indication quickly, turn and hold the indicator selector knob (2). To set the hour indication, push the indicator selector knob (2) and the minute indication will blink. 3) To change the minute indication, turn the indicator selector knob (2) left or right repeatedly when the minute indication blinks. To change the minute indication quickly, turn and hold the indicator selector knob (2). To set the minute indication, push the indicator selector knob (2). When the ignition switch is in the “ON” position, the display (B) shows the fuel gauge. Refer to “Fuel Gauge” in this section. EXAMPLE (a) Trip meter / Odometer / Fuel consumption / Driving range When the ignition switch is in the “ON” position, the display (C) shows one of the following indications, trip meter A, trip meter B, odometer, instantaneous fuel consumption, average fuel consumption or driving range. To switch the display indication (C), push the trip meter selector knob (1) or the indicator selector knob (2) quickly. (b) (c) (d) (e) WARNING If you attempt to adjust the display while driving, you could lose control of the vehicle. (f) Do not attempt to adjust the display while driving. NOTE: When you reconnect the negative (–) terminal to the battery, the clock indication will be reinitialized. Change the indication again to your preference. 76MH0A045 Push the trip meter selector knob (1). Push the knob (2). indicator selector 42 2-31 76MH1-74E BEFORE DRIVING 76MH1-74E (a) (b) (c) (d) (e) (f) Trip meter A Trip meter B Odometer Instantaneous fuel consumption Average fuel consumption Driving range WARNING If you attempt to adjust the display while driving, you could lose control of the vehicle. Do not attempt to adjust the display while driving. NOTE: • Indications will change when you push and release a knob. • The display shows estimated values. Indications may not be the same as actual values. Trip meter The trip meter can be used to measure the distance traveled on short trips or between fuel stops. You can use the trip meter A or trip meter B independently. To reset the trip meter to zero, push and hold the trip meter selector knob (1) for a while when the display shows the trip meter. NOTE: The indicated maximum value of the trip meter is 9999.9. When you run past the maximum value, the indicated value will return to 0.0. Odometer The odometer records the total distance the vehicle has been driven. NOTICE Keep track of your odometer reading and check the maintenance schedule regularly for required services. Increased wear or damage to certain parts can result from failure to perform required services at the proper mileage intervals. Instantaneous Fuel Consumption The display shows the value of instantaneous fuel consumption only when the vehicle is moving. NOTE: • The display does not show the value unless the vehicle is moving. • The indicated maximum value of instantaneous fuel consumption is 30. No more than 30 will be indicated on the display even if the actual instantaneous fuel consumption is higher. • The indication on the display may be delayed if fuel consumption is greatly affected by driving conditions. • The display shows estimated values. Indications may not be the same as actual values. • You can change the units that instantaneous fuel consumption is displayed in. Refer to “Average fuel consumption” in this section. Average fuel consumption If you selected average fuel consumption the last time you drove the vehicle, the display shows the last value of average fuel consumption from previous driving when the ignition switch is turned to the “ON” position. Unless you reset the value of average fuel consumption, the display indicates the value of average fuel consumption which includes average fuel consumption during previous driving. To reset the average fuel consumption to zero, push and hold the indicator selector knob (2) for a while when the display shows the average fuel consumption. NOTE: When you reset the indication or reconnect the negative (–) terminal to the battery, the value of average fuel consumption will be shown after driving for a while. To change the unit of average fuel consumption, while pushing and holding the trip meter selector knob (1), turn the indicator selector knob (2). (Initial setting) EXAMPLE 76MH0A046 43 2-32 76MH1-74E BEFORE DRIVING NOTE: • When you change the units that average fuel consumption is displayed in, the instantaneous fuel consumption units will be changed automatically. • When you reconnect the negative (–) terminal to the battery, the unit of the average fuel consumption will be reinitialized. Change the unit again to your preference. Driving range If you selected driving range the last time you drove the vehicle, the display indicates “---” for a few seconds and then indicates the current driving range when the ignition switch is turned to the “ON” position. The driving range shown in the display is the approximate distance you can drive until the fuel gauge indicates “E”, based on current driving conditions. When the low fuel warning light comes on, the display “---” will appear. If the low fuel warning light comes on, fill the fuel tank immediately regardless of the value of driving range shown in the display. As the driving range after refueling is calculated based on the most recent driving condition, the value is different each time you refuel. NOTE: • If you refuel when the ignition switch is in the “ON” position, the driving range may not indicate the correct value. • When you reconnect the negative (–) terminal to the battery, the value of driving range will be shown after driving for a while. 76MH1-74E Gear position indicator (for Auto Gear Shift models) EXAMPLE 76MH0A044 When the ignition switch is in the “ON” position, the display (D) indicates the gear position. For details on how to use the transaxle, refer to “Using the Transaxle” in the “OPERATING YOUR VEHICLE” section. When the display (C) shows the driving range, you can change the unit of temperature. To change the unit of temperature, while pushing and holding the trip meter selector knob (1), turn the indicator selector knob (2). EXAMPLE Thermometer (if equipped) When the ignition switch is in the “ON” position, the display (E) shows the thermometer. The thermometer indicates the outside temperature. EXAMPLE NOTE: • The outside temperature indication is not the actual outside temperature when driving at low speed, or when stopped. • If there is something wrong with the thermometer, or just after the ignition switch is turned to the “ON” position, the display may not indicate the outside temperature. (Initial setting) (g) 76MH0A042 If the outside temperature nears freezing, the mark (g) will appear on the display. 76MH0A043 NOTE: When you reconnect the negative (–) terminal to the battery, the unit of temperature will be reinitialized. Change the unit again to your preference. 44 2-33 76MH1-74E BEFORE DRIVING 76MH1-74E Setting Mode In the setting mode, you can set up the following functions. Indication Functions Temperature unit (if equipped) “tE” Time indication of clock “CL” Central door locking system “d1” Automatic door locking function “d2” Automatic door unlocking function “d3” Door locking and unlocking siren “d5” 45 2-34 76MH1-74E BEFORE DRIVING 76MH1-74E Indication Functions Additional flashes of the turn signal “L2” Security system “S1” Shock sensor “S2” Pre-warning sensitivity of the shock sensor “S3” Full blast warning sensitivity of the shock sensor “S4” Initialization setting “de-on” Exit the setting mode “End” 46 2-35 76MH1-74E BEFORE DRIVING 76MH1-74E Turn the indicator selector knob (2). Push the knob (2). indicator selector NOTE: Depending on vehicle’s specifications, some items may not be displayed. How to operate the setting mode: 1) When the ignition switch is in the “ON” position and the vehicle is stationary, push the trip meter selector knob (1) to switch the information display indication (C) to the odometer. 2) Push and hold the indicator selector knob (2) until the display shows “tEnP” or “CLoCK”. 3) Turn and/or push the indicator selector knob (2) to select a function that you want to set up according to the above chart. 4) Turn and/or push the indicator selector knob (2) to register settings of the following functions. Temperature unit (if equipped) “tE” • tE-CEL: °C setting (default setting) • tE-FAh: °F setting Time indication of clock “CL” • CL-12h: 12-hour format (default setting) • CL-24h: 24-hour format Central door locking system “d1” • d1-SL1: Unlock all doors by turning the key or pushing the keyless entry system transmitter once • d1-SL2: Unlock all doors by turning the key or pushing the keyless entry system transmitter twice (default setting) Automatic door locking function “d2” • d2-SL1: Disable the automatic door locking function • d2-SL2: Lock all doors when the vehicle speed reaches 15 km/h (default setting) Automatic door unlocking function “d3” • d3-SL1: Disable the automatic door unlocking function • d3-SL3: Unlock all doors when the key is pulled out from the ignition switch (default setting) Door locking and unlocking siren “d5” • d5-SL1: Siren sounds when the door(s) is(are) locked or unlocked by using the keyless entry system transmitter (default setting) • d5-SL2: Siren does not sound when the door(s) is(are) locked or unlocked by using the keyless entry system transmitter Additional flashes of the turn signal “L2” • L2-SL1: Turn signal flashes three times after the turn signal lever is returned (default setting) • L2-SL2: Disable the additional flashes of turn signal Security system “S1” • S1-SL1: Enable the security system (default setting) • S1-SL2: Disable the security system Shock sensor “S2” • S2-SL1: Enable the shock sensor • S2-SL2: Disable the shock sensor (default setting) Pre-warning sensitivity of the shock sensor “S3” • S3-L00: Disable the pre-warning • S3-L01 to L15: Adjust the pre-warning sensitivity of shock sensor (Lowest sensitivity level is L01 and highest is L15, and default setting is L14) Full blast warning sensitivity of the shock sensor “S4” • S4-L00: Disable the full blast warning • S4-L01 to L15: Adjust the full blast warning sensitivity of shock sensor (Lowest sensitivity level is L01 and highest is L15, and default setting is L09) Initialization setting “de-on” • de-on: Initialize all settings 47 2-36 76MH1-74E BEFORE DRIVING 76MH1-74E Warning and Indicator Lights EXAMPLE Brake System Warning Light the vehicle’s brake system. If this happens, you should: 1) Pull off the road and stop carefully. WARNING Remember that stopping distance may be longer, you may have to push harder on the pedal, and the pedal may go down farther than normal. 76MH0017 NOTE: • As shown in the above illustration, “ ” indicates on the display of currently setting item. • To go back to the higher level display during operation, turn the indicator selector knob (2) to display “bACK” or “-bAC” and then push the indicator selector knob (2). • If the security system “S1” is in the disabled state, the shock sensor “S2”, prewarning sensitivity “S3” and full blast warning sensitivity “S4” cannot be set up. 5) To exit the setting mode, switch the display to show “End” and then push the indicator selector knob (2). 65D477 Three different types of operations exist depending on the vehicle’s specification. 1) The light comes on briefly when the ignition switch is turned to the “ON” position. 2) The light comes on when the parking brake is engaged with the ignition switch in the “ON” position. 3) The light comes on when under either or both of above two conditions. The light also comes on when the fluid in the brake fluid reservoir falls below the specified level. The light should go out after starting the engine and fully releasing the parking brake, if the fluid level in the brake fluid reservoir is adequate. The light also comes on together with the ABS warning light when the rear brake force control function (proportioning valve function) of the ABS system fails. If the brake system warning light comes on while you are driving the vehicle, it may mean that there is something wrong with 2) Test the brakes by carefully starting and stopping at the side of the road. – If you determine that it is safe, drive carefully at low speed to the nearest dealer for repairs, or – Have the vehicle towed to the nearest dealer for repairs. WARNING If any of the following conditions occur, you should immediately ask your MARUTI SUZUKI dealer to inspect the brake system. • If the brake system warning light does not go out after the engine has been started and the parking brake has been fully released. • If the brake system warning light does not come on when the ignition switch is turned to the “ON” position. • If the brake system warning light comes on at any time during vehicle operation. 48 2-37 76MH1-74E BEFORE DRIVING 76MH1-74E NOTE: Because the disc brake system is selfadjusting, the fluid level will drop as the brake pads become worn. Replenishing the brake fluid reservoir is considered normal periodic maintenance. NOTE: (Parking Brake Reminder Buzzer) (if equipped) A buzzer sounds intermittently to remind you to release the parking brake if you start the vehicle without releasing the parking brake. Make sure that the parking brake is fully released and the brake system warning light turns off. Seat Belt Warning Light (if equipped) “AIR BAG” Light (if equipped) Anti-Lock Brake System (ABS) Warning Light (if equipped) 63J030 This light blinks or comes on for several seconds when the ignition switch is turned to the “ON” position so you can check if the light is working. The light will come on and stay on if there is a problem in the air bag system (if equipped). WARNING 60G049 This light blinks as a reminder until the driver’s seat belt is buckled. For details about the seat belt reminder, refer to “Seat Belts and Child Restraint Systems” in this section. If the “AIR BAG” light does not blink or come on briefly when the ignition switch is turned to the “ON” position, stays on for more than 10 seconds, or comes on while driving, the air bag system (if equipped) may not work properly. Have both systems inspected by an authorized MARUTI SUZUKI dealer. 65D529 When the ignition switch is turned to the “ON” position, the light comes on briefly so you can check that the light is working. If the light stays on, or comes on when driving, there may be something wrong with the ABS. If this happens: 1) Pull off the road and stop carefully. 2) Turn the ignition switch to “LOCK” and then start the engine again. If the warning light comes on briefly then turns off, the system is normal. If the warning light still stays on, the system will be something wrong. If the light and the brake system warning light stay on, or come on simultaneously when driving, your ABS system is equipped with the rear brake force control function (proportioning valve function) and there may be something wrong with both the rear brake force control function and anti-lock function of the ABS system. 49 2-38 76MH1-74E BEFORE DRIVING 76MH1-74E If one of these happens, have the system inspected by your MARUTI SUZUKI dealer. If the ABS becomes inoperative, the brake system will function as an ordinary brake system that does not have this ABS system. Malfunction Indicator Light Electric Power Steering Light NOTICE Continuing to drive the vehicle when the malfunction indicator light is on can cause permanent damage to the vehicle’s emission control system, and can affect fuel economy and driveability. 79J039 Transaxle Warning Light (if equipped) This light comes on when the ignition switch is turned to the “ON” position, and goes out when the engine is started. If this light comes on while driving, the power steering system may not work properly. Have the system inspected by your MARUTI SUZUKI dealer. 63J031 Your vehicle has a computer-controlled emission control system. A malfunction indicator light is provided on the instrument panel to indicate when it is necessary to have the emission control system serviced. The malfunction indicator light comes on when the ignition switch is turned to “ON” position to let you know the light is working and goes out when the engine is started. If the malfunction indicator light comes on when the engine is running, there is a damage with the emission control system. Bring the vehicle to your MARUTI SUZUKI dealer to have the damage fixed. Also, if the light comes on, there may be something wrong with the Auto Gear Shift system. Have the system inspected by an authorized MARUTI SUZUKI dealer. 80J219 This light comes on for several seconds when the ignition switch is turned to the “ON” position so you can check the light is working. If this light comes on when the engine is running, there is a problem with the Auto Gear Shift system. Ask your MARUTI SUZUKI dealer to have the system inspected. NOTE: If the Auto Gear Shift system temperature becomes too high, this light will blink. Stop the vehicle in a safe place and let the system cool down. NOTE: Following operations of the steering wheel while parking or driving at a very lowspeed may have steering effort bigger gradually. This is not a malfunction of the steering system, but the power steering control system limits the power assist in order to prevent them from overheating. • The steering wheel is operated very often. • The steering wheel is kept in a fully turned position for a long while. When the power steering control system cool down, the power steering system back to the original condition. However, repeating these operations could cause the power steering system damaged. 50 2-39 76MH1-74E BEFORE DRIVING 76MH1-74E NOTE: If the power steering system does not work properly, you will feel heavier to steer but you still will be able to steer. NOTE: If the steering is operated, you may hear a noise. This is normal and indicates that the power steering system works properly. Oil Pressure Light High Engine Coolant Temperature Warning Light (red color) NOTICE • If you operate the engine with this light on, severe engine damage can result. • Do not rely on the Oil Pressure Light to indicate the need to add oil. Be sure to periodically check the engine oil level. 54G344 Charging Light 50G051 This light comes on when the ignition switch is turned to the “ON” position, and goes out when the engine is started. The light will come on and remain on if there is insufficient oil pressure. If the light comes on when driving, pull off the road as soon as you can and stop the engine. Check the oil level and add oil if necessary. If there is enough oil, the lubrication system should be inspected by your MARUTI SUZUKI dealer before you drive the vehicle again. 50G052 This light comes on when the ignition switch is turned to the “ON” position, and goes out when the engine is started. The light will come on and remain on if there is something wrong with the battery charging system. If the light comes on when the engine is running, the charging system should be inspected immediately by your MARUTI SUZUKI dealer. When the ignition switch is turned to the “ON” position, this light comes on briefly so you can check that the light is working. If this light blinks while driving, it means the engine is running hot. Avoid driving conditions that may lead to actual overheating. If the light stays on without blinking, then the engine is overheating. Follow the instructions in the “If the Engine Overheats” of “EMERGENCY SERVICE” section. NOTICE Continuing to drive the vehicle when engine overheating is indicated can result in severe engine damage. 51 2-40 76MH1-74E BEFORE DRIVING 76MH1-74E Immobilizer System Light If any door (including the tailgate) is open when the vehicle is moving, a ding sounds to remind you to close all doors completely. Low Fuel Warning Light 80JM122 When the ignition switch is turn to the “ON” position, this light comes on briefly so you can check that the light is working. If this light brinks with the ignition switch is turn to the “ON” , the engine will not start. NOTE: If this light blinks, turn the ignition switch to the “LOCK” position, then turn it back to the “ON” position. If the light still blinks with the ignition switch turned to the “ON” position, there may be something wrong with your key or with the immobilizer system. Ask your MARUTI SUZUKI dealer to inspect the system. Open Door Warning Light When you turn on the left or right turn signals, the corresponding green arrow on the instrument panel will flash along with the respective turn signal lights. When you turn on the hazard warning switch, both arrows will flash along with all of the turn signal lights. Main Beam (high beam) Indicator Light 54G343 If this light comes on, fill the fuel tank immediately. When this light comes on, a ding sounds once to remind you to fill the fuel. If you do not fill the fuel, a ding sounds every time when the ignition switch is turned to the “ON” position. NOTE: The activation point of this light varies depending on road conditions (for example, slope or curve) and driving conditions because of fuel moving in the tank. 50G056 This indicator comes on when headlight main beams (high beams) are turned on. Security System Indicator (if equipped) Turn Signal Indicators 82K269 For details about the security system, refer to “Security System” in this section. 54G391 This light remains on until all doors (including the tailgate) are completely closed. 50G055 52 2-41 76MH1-74E BEFORE DRIVING 76MH1-74E NOTE: If the security system indicator blinks when the ignition switch is in the “ON” position, there may be something wrong with the security system. Ask your MARUTI SUZUKI dealer to inspect the system. details of draining water, refer to “Fuel Filter” in the “INSPECTION AND MAINTENANCE” section. Glow Plug Indicator Light (For Diesel Engine Model) WARNING To avoid possible injury, do not operate controls by reaching through the steering wheel. Lighting Operation Depress Brake Pedal Indicator (if equipped) EXAMPLE (3) 60A543 76MH0A047 Refer to “Auto Gear Shift” in the “OPERATING YOUR VEHICLE” section for details. Fuel Filter Warning Light (For Diesel Engine Model) If the coolant temperature is cool enough, this light comes on when the ignition switch is turned to the “ON” position and goes out when the glow plug is heated enough for engine starting. (2) (1) 60MK011 To turn the lights on or off, twist the knob on the end of the lever. There are three positions: Lighting Control Lever OFF (1) All lights are off. (2) Front position lights, tail lights, license plate light and instrument lights are on, but headlights are off. 60A541 This light comes on for several seconds when the ignition switch is turned to the “ON” position so you can check the light is working. If the light comes on when driving, there is a possibility to have water in the fuel filter. Drain water as soon as possible. For (3) Front position lights, tail lights, license plate light, instrument lights and headlights are on. 65D611 53 2-42 76MH1-74E BEFORE DRIVING 76MH1-74E Front Fog Light Switch (if equipped) EXAMPLE Headlight Leveling Switch 60MK012 With the headlights on, push the lever forward to switch to the high beams (main beams) or pull the lever toward you to switch to the low beams. When the high beams (main beams) are on, a light on the instrument panel will come on. To momentarily activate the high beams (main beams) as a passing signal, pull the lever slightly toward you and release it when you have completed the signal. Lights “On” reminder (if equipped) A buzzer/chime sounds to remind you to turn off the lights if they are left on when the ignition key is removed and the driver’s door is opened. EXAMPLE EXAMPLE 64J058 The front fog light comes on when the fog light switch is pushed in with the position lights, tail lights and/or the headlights are on. An indicator light above the switch will be lit when the front fog light is on. NOTE: In some countries the lighting operation may be different from the above description according to local regulations. 80JM040 Level the headlight beam according to the load condition of your vehicle by turning this switch. The chart below shows the appropriate switch position for different vehicle-load conditions. Vehicle Load Condition Switch Position Driver only 0 Driver + 1 passenger (in front seat) 0 Driver + 4 passengers, no cargo 1 Driver + 4 passengers, cargo added 2 Driver + full cargo 3 54 2-43 76MH1-74E BEFORE DRIVING 76MH1-74E Turn Signal Control Lever to cancel the turn signal. For convenience, you can flash the turn signal by moving the lever part way and holding it there. The lever will return to its normal position when you release it. Normal turn signal NOTE: The turn signal and its indicator flash three times even if you return the lever immediately after moving it. EXAMPLE 60MK013 65D611 WARNING To avoid possible injury, do not operate controls by reaching through the steering wheel. Move the lever all the way upward or downward to signal. When the turn is completed, the signal will cancel and the lever will return to its normal position. Lane change signal Turn Signal Operation NOTE: The turn signal and its indicator can be set whether they flash three times after the turn signal lever is returned via the information display. Refer to “Information Display” in this section. NOTE: You can customize the setting for the number of times of flashing of the turn signal and its indicator. Please ask an authorized MARUTI SUZUKI dealer for the customization. With the ignition switch in the “ON” position, move the lever up or down to activate the right or left turn signals. EXAMPLE 60MK014 Sometimes, such as when changing lanes, the steering wheel is not turned far enough 55 2-44 76MH1-74E BEFORE DRIVING 76MH1-74E Hazard Warning Switch Windshield Wiper and Washer Lever Windshield Wipers EXAMPLE 76MH0A049 EXAMPLE 76MH0A048 Push in the hazard warning switch to activate the hazard warning lights. All turn signal lights and both turn signal indicators will flash simultaneously. To turn off the lights, push the switch again. Use the hazard warning lights to warn other traffic during emergency parking or when your vehicle could otherwise become a traffic hazard. 65D611 WARNING To avoid possible injury, do not operate controls by reaching through the steering wheel. Wiper and Washer Operation When the ignition switch is in the “ON” position, you can use the wiper/washer lever or switch (if equipped). To turn the windshield wipers on, move the lever down to one of the three operating positions. In the “INT” position, the wipers operate intermittently. The “INT” position is very convenient for driving in mist or light rain. In the “LO” position, the wipers operate at a steady low speed. In the “HI” position, the wipers operate at a steady high speed. To turn off the wipers, move the lever back to the “OFF” position. Move the lever up and hold it to the “MIST” position, the windshield wipers will turn on continuously at low speed. 56 2-45 76MH1-74E BEFORE DRIVING 76MH1-74E Windshield Washer NOTICE EXAMPLE 76MH0A050 To spray windshield washer fluid, pull the lever toward you. The windshield wipers will automatically turn on at low speed if they are not already on and the “INT” position is equipped. WARNING • To prevent windshield icing in cold weather, turn on the defroster to heat the windshield before and during windshield washer use. • Do not use radiator antifreeze in the windshield washer reservoir. It can severely impair visibility when sprayed on the windshield, and can also damage your vehicle’s paint. To help prevent damage to the windshield wiper and washer system components, you should take the following precautions: • Do not continue to hold in the lever when there is no windshield washer fluid being sprayed or the washer motor can be damaged. • Do not attempt to remove dirt from a dry windshield with the wipers or you can damage the windshield and the wiper blades. Always wet the windshield with washer fluid before operating the wipers. • Clear ice or packed snow from the wiper blades before using the wipers. • Check the washer fluid level regularly. Check it often when the weather is bad. • Only fill the washer fluid reservoir 3/4 full during cold weather to allow room for expansion if the temperature falls low enough to freeze the solution. Rear Window Wiper/Washer Switch (if equipped) EXAMPLE Washer Wiper 76MH0A051 To turn the rear wiper on, twist the rear wiper switch on the end of the lever forward to the “ON” position. To turn the rear wiper off, twist the switch rearward to the “OFF” position. With the rear wiper in the “OFF” position, twist the switch rearward and hold it there to spray window washer fluid. With the rear wiper in the “ON” position, turn the switch forward and hold it there to spray window washer fluid. NOTICE Clear ice or snow from the rear window and rear wiper blade before using the rear wiper. Accumulated ice or snow could prevent the wiper blade from moving, causing damage to the wiper motor. 57 2-46 76MH1-74E BEFORE DRIVING 76MH1-74E Tilt Steering Lock Lever (if equipped) Horn When the rear window is misted, push this switch (1) to clear the window. EXAMPLE An indicator light will be lit when the defogger is on. The defogger will work only when the engine is running. To turn off the defogger, push the switch again. EXAMPLE NOTICE 68LM240 74LHT0333 (1) Lock (2) Unlock The lock lever is located under the steering column. To adjust the steering wheel height: 1) Push down the lock lever to unlock the steering column. 2) Adjust the steering wheel to the desired height and lock the steering column by pull up the lock lever. 3) Try moving the steering wheel up and down to make sure it is securely locked in position. Press the horn button of the steering wheel to sound the horn. The horn will sound with the ignition switch in any position. Heated Rear Window Switch (if equipped) The heated rear window uses a large amount of electricity. Be sure to turn off after the window has become clear. NOTE: • The defogger will work only when the engine is running. • The defogger will automatically turn off after the defogger remains on for 15 minutes to prevent discharging of the battery. (1) WARNING Never attempt to adjust the steering wheel height while the vehicle is moving or you could lose control of the vehicle. EXAMPLE 76MH0A052 58 2-47 76MH1-74E 76MH1-74E OPERATING YOUR VEHICLE OPERATING YOUR VEHICLE Exhaust Gas Warning ......................................................... 3-1 Daily Inspection Checklist .................................................. 3-1 Engine Oil Consumption .................................................... 3-2 Ignition Switch ..................................................................... 3-3 Parking Brake Lever ........................................................... 3-4 Pedal ..................................................................................... 3-5 Starting the Engine ............................................................. 3-6 Using the Transaxle ............................................................ 3-7 Braking ................................................................................. 3-15 59 76MH1-74E OPERATING YOUR VEHICLE 76MH1-74E Exhaust Gas Warning WARNING 52D334 WARNING Avoid breathing exhaust gases. Exhaust gases contain carbon monoxide, a potentially lethal gas that is colorless and odorless. Since carbon monoxide is difficult to detect by itself, be sure to take the following precautions to help prevent carbon monoxide from entering your vehicle. • Do not leave the engine running in garages or other confined areas. (Continued) 3-1 (Continued) • Do not park with the engine running for a long period of time, even in an open area. If it is necessary to sit for a short time in a parked vehicle with the engine running, make sure the air intake selector is set to “FRESH AIR” and the fan is at high speed. • Avoid operating the vehicle with the tailgate or trunk open. If it is necessary to operate the vehicle with the tailgate or trunk open, make sure the sunroof (if equipped) and all windows are closed, and the blower is at high speed with the air intake selector set to “FRESH AIR”. • To allow proper operation of your vehicle’s ventilation system, keep the air inlet grille in front of the windshield clear of snow, leaves, or other obstructions at all times. • Keep the exhaust tailpipe area clear of snow and other material to help reduce the buildup of exhaust gases under the vehicle. This is particularly important when parked in blizzard conditions. • Have the exhaust system inspected periodically for damage and leaks. Any damage or leaks should be repaired immediately. Daily Inspection Checklist Before Driving 60A187S 1) Make sure that windows, mirrors, lights, and reflectors are clean and unobstructed. 2) Visually check the tires for the following points: – the depth of the tread groove – abnormal wear, cracks and damage – loose wheel nuts – existence of foreign material such as nails, stones, etc. Refer to “Tires” in “INSPECTION AND MAINTENANCE” section for details. 3) Look for fluid and oil leaks. 60 76MH1-74E OPERATING YOUR VEHICLE 76MH1-74E NOTE: It is normal for water to drip from the air conditioning system after use. 4) Make sure the hood is fully closed and latched. 5) Check the headlights, turn signal lights, brake lights and horn for proper operation. 6) Adjust the seat and head restraint (if equipped). 7) Check the brake pedal and the parking brake lever. 8) Adjust the mirrors. 9) Make sure that you and all passengers have properly fastened your seat belts. 10)Make sure that all warning lights come on as the key is turned to the “ON” position. 11)Check all gauges. 12)Make sure that the BRAKE SYSTEM WARNING light turns off when the parking brake is released. Once a week, or each time you fill your fuel tank, perform the following under-hood checks: 1) 2) 3) 4) 5) 6) Engine oil level Coolant level Brake fluid level Windshield washer fluid level Battery solution level Hood latch operation Pull the hood release handle inside the vehicle. Make sure that you cannot open the hood all the way without releasing the secondary latch. Be sure to close the hood securely after checking for proper latch operation. See “All latches, hinges & locks” of “CHASSIS AND BODY” in the “Periodic Maintenance Schedule” in the “INSPECTION AND MAINTENANCE” section for lubrication schedule. WARNING Make sure the hood is fully closed and latched before driving. If it is not, it can fly up unexpectedly during driving, obstructing your view and resulting in an accident. Once a month, or each time you fill your fuel tank, check the tire pressure using a tire pressure gauge. Also check the tire pressure of the spare tire. Engine Oil Consumption It is normal for the engine to consume some engine oil during normal vehicle operation. The amount of engine oil consumed depends on the viscosity of the oil, the quality of the oil and the conditions the vehicle is driven under. More oil is consumed during high-speed driving and when there is frequent acceleration and deceleration. Under high loads, your engine also will consume more oil. A new engine also consumes more oil, since its pistons, piston rings and cylinder walls have not yet become conditioned. New engines reach the normal level of oil consumption only after approximately 5000 km (3000 miles) driving. Oil consumption: Max. 1.0 L per 1000 km (1 Qt. per 600 miles) When judging the amount of oil consumption, note that the oil may become diluted and make it difficult to accurately judge the true oil level. As an example, if a vehicle is used for repeated short trips, and consumes a normal amount of oil, the dipstick may not show any drop in the oil level at all, even after 1000 km (600 miles) or more of driving. This is because the oil is gradually becoming diluted with fuel or moisture, making it appear that the oil level has not changed. You should also be aware that the diluting ingredients evaporate out when the vehicle is subsequently driven at high speeds, such as on an expressway, making it appear that oil is excessively consumed after high-speed driving. 61 3-2 76MH1-74E OPERATING YOUR VEHICLE 76MH1-74E Ignition Switch Turn to “LOCK” Ignition key reminder (if equipped) A buzzer sounds intermittently to remind you to remove the ignition key if it is in the ignition switch when the driver’s door is opened. Push 65D611 WARNING To avoid possible injury, do not operate controls by reaching through the steering wheel. START This is the position for starting the engine using the starter motor. The key should be released from this position as soon as the engine starts. 60G033 You must push in the key to turn it to the “LOCK” position. It locks the ignition, and prevents normal use of the steering wheel after the key is removed. To release the steering lock, insert the key and turn it clockwise to one of the other positions. If you have trouble turning the key to unlock the steering, try turning the steering wheel slightly to the right or left while turning the key. EXAMPLE ACC Accessories such as the radio can operate, but the engine is off. 52KM052 The ignition switch has the following four positions: LOCK This is the normal parking position. It is the only position in which the key can be removed. ON This is the normal operating position. All electrical systems are on. 81A297S WARNING • Never remove the ignition key while the vehicle is moving. The steering wheel will lock and you will not be able to steer the vehicle. (Continued) 62 3-3 76MH1-74E OPERATING YOUR VEHICLE 76MH1-74E WARNING (Continued) • Always remove the ignition key when leaving the vehicle even if only for a short time. Also do not leave children alone in a parked vehicle. Unattended children could cause accidental movement of the vehicle or could tamper with power windows or power sunroof. They also could suffer from heat stroke in warm or hot weather. These could result in severe injury or even death. Parking Brake Lever WARNING • Never drive your vehicle with the parking brake on: rear brake effectiveness can be reduced from overheating, brake life may be shortened, or permanent brake damage may result. • If the parking brake does not hold the vehicle securely or does not fully release, have your vehicle inspected immediately by an authorized MARUTI SUZUKI dealer. EXAMPLE (1) (2) (3) 62J100 NOTICE • Do not use the starter motor for more than 12 seconds at a time. For diesel engine model, do not use the starter motor for more than 30 seconds at a time. If the engine does not start, wait 15 seconds before trying again. If the engine does not start after several attempts, check the fuel and ignition systems or consult your MARUTI SUZUKI dealer. • Do not leave the ignition switch in the “ON” position if the engine is not running as the battery will discharge. (1) To set (2) To release (3) To release The parking brake lever is located between the seats. To set the parking brake, hold the brake pedal down and pull the parking brake lever all the way up. To release the parking brake, hold the brake pedal down, pull up slightly on the parking brake lever, push the button on the end of the lever with your thumb, and lower the lever to its original position. WARNING Always set the parking brake fully before leaving your vehicle or it may move, causing injury or damage. When parking, make sure the gearshift lever is in reverse or first gear. Remember, even though the transaxle is in gear, you must set the parking brake fully. 63 3-4 76MH1-74E OPERATING YOUR VEHICLE WARNING When parking the vehicle in extremely cold weather, the following procedure should be used: 1) Set the parking brake. 2) Manual transaxle - turn off the engine, then shift into reverse or first gear. Auto Gear Shift – shift into reverse or first gear and check the gear position indicator in the instrument cluster to make sure that the transaxle is engaged in 1st or reverse, then turn off the engine. 3) Get out of the vehicle and put chocks under the wheels. 4) Release the parking brake. When you return to your vehicle, you must remember to first set the parking brake, then remove the wheel chocks. NOTE: (For Auto Gear Shift Model) For details on how to use the gearshift lever to park the vehicle, refer to “Parking” in “Auto Gear Shift” in this section. 76MH1-74E Parking Brake Reminder Buzzer (if equipped) Clutch Pedal (1) (For manual transaxle) A buzzer sounds intermittently to remind you to release the parking brake if you start the vehicle without releasing the parking brake. Make sure that the parking brake is fully released and the brake system warning light turns off. The clutch pedal is used to disengage the drive to the wheels when starting the engine, stopping, or shifting the gearshift lever. Depressing the pedal disengages the clutch. WARNING Pedal Do not drive with your foot resting on the clutch pedal. It could result in excessive clutch wear, clutch damage, or unexpected loss of engine braking. Manual transaxle EXAMPLE (1) (2) Brake Pedal (2) Your MARUTI SUZUKI vehicle is equipped with front disc brakes and rear drum brakes. Depressing the brake pedal applies both sets of brakes. (3) 80J2121 Auto Gear Shift EXAMPLE You may hear occasional brake squeal when you apply the brakes. This is a normal condition caused by environmental factors such as cold, wet, snow, etc. WARNING (2) If brake squeal is excessive and occurs each time the brakes are applied, you should have the brakes checked by your MARUTI SUZUKI dealer. (3) 80J2122 64 3-5 76MH1-74E OPERATING YOUR VEHICLE 76MH1-74E WARNING Do not “ride” the brakes by applying them continuously or resting your foot on the pedal. This will result in overheating of the brakes which could cause unpredictable braking action, longer stopping distances, or permanent brake damage. Accelerator Pedal (3) This pedal controls the speed of the engine. Depressing the accelerator pedal increases power output and speed. Starting the Engine Before Starting the Engine the way to the floor. Hold the clutch pedal while starting the engine. Auto Gear Shift – Shift into “N” (Neutral) and depress the brake pedal. Hold the brake pedal while starting the engine. If the engine still does not start, try holding the accelerator pedal all the way to the floor while cranking. This should clear the engine if it is flooded. WARNING Cold engine Turn the ignition switch to the “ON” position and wait until the glow plug indicator goes out if it comes on. Crank the engine by turning the ignition key to “START”. Release the key when the engine starts. Make sure that the parking brake is set fully and the transaxle is in Neutral before attempting to start the engine. Starting a Cold and Warm Engine (For Petrol Engine Model) With your foot off the accelerator pedal, crank the engine by turning the ignition key to “START”. Release the key when the engine starts. NOTICE • Stop turning the starter immediately after the engine has started or the starter system can be damaged. • Do not crank the engine for more than 12 seconds at a time. If the engine doesn’t start on the first try, wait about 15 seconds before trying again. Auto Gear Shift 76MH021 1) Make sure the parking brake is set fully. 2) Manual transaxle – Shift into “N” (Neutral) and depress the clutch pedal all If the engine does not start after 12 seconds of cranking, wait about 15 seconds, then press down the accelerator pedal to 1/3 of its travel and try cranking the engine again. Release the key and accelerator pedal when the engine starts. (For Diesel Engine Model) NOTICE • Stop turning the starter immediately after the engine has started or the starter system can be damaged. • Do not crank the engine for more than 30 seconds at a time. If the engine doesn’t start on the first try, wait about 15 seconds before trying again. Warm engine Crank the engine by turning the ignition key to “START”. Release the key when the engine starts. Caution when stopping the engine with turbocharger When stopping the engine after climbing or high speed driving, let the engine idle for about one minute or more (if it is not prohibited) to cool down the turbocharger and engine oil. This is to prevent the engine oil from over-deteriorating. Deteriorated engine oil will damage the bearings of the turbocharger. 65 3-6 76MH1-74E OPERATING YOUR VEHICLE 76MH1-74E Restarting diesel engine after fuelempty stop If the engine stops and the low fuel warning light and the malfunction indicator light come on, use the following procedure: 1) Fill the fuel tank. 2) Hold the ignition key in “ON” position for 5–10 seconds to feed fuel. 3) Perform above engine starting procedure to start the engine. If the malfunction indicator light still comes on after the engine started, there may be some problem with the engine. Ask your MARUTI SUZUKI dealer to have the engine inspected. release the clutch. When you hear a change in the engine’s sound, slowly press the accelerator while continuing to gradually release the clutch. Shifting All forward gears are synchronized, which provides for quiet and easy shifting. Always push in the clutch pedal fully before shifting gears. Downshifting speeds maximum allowable km/h Using the Transaxle 2nd to 1st 10 Manual Transaxle 3rd to 2nd 37 4th to 3rd 55 5th to 4th OK at all For E08A diesel engine Downshifting 68KH032 Starting off To start off, depress the clutch pedal all the way to the floor and shift into 1st gear. After releasing the parking brake, gradually Keep the engine speed so it does not get into the red zone of tachometer. WARNING For K10B Petrol engine Downshifting NOTICE When downshifting to a lower gear, make sure not to downshift at the speed faster than the maximum allowable speeds, or severe engine damage can result. km/h • Reduce your speed and downshift to a lower gear before going down a long or steep hill. A lower gear will allow the engine to provide braking. Avoid riding the brakes or they may overheat, resulting in brake failure. • When driving on slippery roads, be sure to slow down before downshifting. Excessive and or sudden changes in engine speed may cause loss of traction, which could cause you to lose control. 2nd to 1st 29 3rd to 2nd 55 NOTICE 4th to 3rd 85 5th to 4th 109 Make sure that the vehicle is completely stationary before you shift into reverse. *NOTE: You may not accelerate to the maximum allowable speed because of the driving situation and/or the vehicle condition. 66 3-7 76MH1-74E OPERATING YOUR VEHICLE 76MH1-74E The features are as follows: NOTICE • To help avoid clutch damage, do not use the clutch pedal as a footrest while driving or use the clutch to keep the vehicle stationary on a slope. Depress the clutch fully when shifting. • When shifting or starting off, do not race the engine. Racing the engine can shorten engine life and affect smooth shifting. R - N M D + Auto Gear Shift Auto Gear Shift is a 5-speed forward/ reverse transaxle. Auto Gear Shift has the basic features of conventional manual transaxle, but clutch operation and transaxle gear shifting are controlled electronically. NOTICE Do not depress both the brake pedal and accelerator pedal simultaneously. This can cause damage or overheating to the clutch. NOTE: When you open the driver’s door, the Auto Gear Shift systems run automatically and you may hear an operating noise. This sound does not indicate a malfunction. 76MH0A054 R M + R N - N D M D This light will come on if you do not depress the brake pedal in the following situations. • When starting the engine. • When the engine is on and the gearshift lever is shifted from “N” position to “D”, “M” or “R” position. • When the ignition switch is in the “ON” position and the engine is off, the gearshift lever is shifted into any position. This light will also come on if one of the gears cannot be engaged and the system is unable to re-try shifting when you shift the gearshift lever from “N” position to “D”, “M” or “R” position. Starting the engine When starting the engine, always place the gearshift lever in the “N” position and depress the brake pedal firmly. The engine cannot be started unless the gearshift lever is in the “N” position and the brake pedal is depressed. + 76MH0A055 Depress brake pedal indicator 76MH0A056 76MH0A047 Clutch operation You can select either the Drive (D) mode or the Manual (M) mode. Since this vehicle controls clutch operation electronically in either mode, you do not need to operate the clutch. 67 3-8 76MH1-74E OPERATING YOUR VEHICLE Creeping function This vehicle has a creeping function that helps the vehicle to start smoothly by engaging the clutch. When the gearshift lever is in any of the positions “D”, “M” or “R”, and you release your foot from the brake pedal, the vehicle starts slowly without depressing the accelerator pedal. The creeping function is disabled if you depress the brake pedal or pull up the parking brake lever. NOTE: If the driver’s door is opened and/or the parking brake lever is engaged with the gear in the “M”, “D” or “R” position, the creeping function will not operate. Parking and Stopping the vehicle Auto Gear Shift does not have a parking position. The vehicle can be parked with the gearshift lever in any position. When stopping the vehicle, the gear will be shifted to 1st. NOTICE A buzzer will sound continuously if the vehicle is operated with the gearshift lever in-between of each shift positions. The vehicle will become inoperative if you continue to operate the vehicle with the gearshift lever inbetween shift positions. 76MH1-74E Drive (D) mode When the Drive (D) mode is activated, the most appropriate gear position is automatically selected upon operation of the accelerator pedal and variation of vehicle speed. Normal driving: 1) Start the engine as instructed in “Starting the engine” in this section. 2) With your foot on the brake pedal, shift the gearshift lever to the “D” position. When the gearshift lever is shifted to the “D” position, the gear will be shifted to 1st. • The “N” indicator will flash, the depress brake pedal indicator will come on and a warning buzzer (long pulse sound) will sound if any of the following cases occur; – If you shift the gearshift lever from the “N” to the “D” position without depressing the brake pedal – If the system is unable to re-try shifting You should depress the brake pedal and shift the gearshift lever to “N” position, then shift to “D” again. 3) Release the parking brake and brake pedal. 4) Depress the accelerator pedal slowly. WARNING 76MH0A057 NOTE: • If 1st gear cannot be engaged even though the gearshift lever has been shifted from the “N” to the “D” position, the system will re-try shifting automatically. This will take some time, noise may be heard from the gears, and shifting gear shock may occur. However, they do not indicate a malfunction. • While driving the vehicle, do not shift the gearshift lever to the “N” position. The engine brake may not work and you may get involved in an unexpected accident. If you return the gearshift lever from “N” to “D” because of unintended shifting, the gear position will be shifted according to the current vehicle speed. • Always keep your foot on the brake pedal while stopped with the engine running. This operation prevents the vehicle from moving due to unintended activation of the creeping function. 68 3-9 76MH1-74E OPERATING YOUR VEHICLE 76MH1-74E Starting off on an uphill/downhill: NOTICE If the gearshift lever cannot shift into any position, or the gear is changed to “N” position automatically when the vehicle speed becomes less than 10 km/h (6 mph), there may be a systematic malfunction. In this case, ask your MARUTI SUZUKI dealer to inspect the Auto Gear Shift system as soon as possible. NOTICE Do not operate the system as described below. The life cycle of the clutch may be reduced. • Using the accelerator pedal to hold the vehicle on an uphill slope with the gearshift lever in the “D” or “M” position. If you perform this operation for a certain period of time, a warning buzzer will sound. • Shifting the gearshift lever to the “D”, “M” or “R” position while racing the engine. • Driving at low speed using a high gear. • Holding the vehicle on an uphill slope using the creeping function. If you perform this operation for a certain period of time, a warning buzzer will sound. Uphill 1) Apply the parking brake firmly so that the vehicle does not roll backwards. 2) Shift the gearshift lever to the “D” position while depressing the brake pedal. Make sure that the gear position indicator in the instrumental cluster displays 1st gear. 3) Release the brake pedal and depress the accelerator pedal gradually, and when the vehicle starts to move, release the parking brake and depress the accelerator pedal to start off. NOTICE On an uphill slope, never hold the vehicle at a stop using only the accelerator pedal or the creeping function. If you perform this operation for a certain period of time, a warning buzzer will sound, and in some cases the engine will stall. This can also cause excessive damage to the clutch. Downhill 1) Depress the brake pedal and shift the gearshift lever to the “D” position. Make sure that the gear is in 1st by checking the gear position indicator. 2) Release the brake pedal and depress the accelerator pedal slowly. Even if the accelerator pedal is not depressed, the clutch will be engaged when the vehicle speed increases. Using engine braking: When driving on a downhill slope, downshifting is recommended. So you can use engine braking. By placing the gearshift lever in the “M” position, the Manual (M) mode is selected, and you can shift to a lower gear manually. For details of downshift operation, refer to “Upshift and downshift” in the “Manual (M) mode”. Manual (M) mode The gears are not shifted automatically. To shift the transaxle, the driver must operate the gearshift lever to the “+” or “–” direction. As for conventional manual transaxle vehicles, releasing the accelerator pedal a little may help the transaxle to shift smoothly. Upshift and downshift: Upshifting R - N M D + 76MH0A058 69 3-10 76MH1-74E OPERATING YOUR VEHICLE 76MH1-74E Pull the gearshift lever to the “+” direction and release it. Every time the lever is operated, the transaxle is upshifting 1 step in the order of 1st  2nd  3rd  4th  5th gear. WARNING 76MH0A061 76MH0A059 Downshifting R - N M D + 76MH0A060 Push the gearshift lever to the “–” direction and release it. Every time the lever is operated, the transaxle is downshifted in the order 5th  4th  3rd  2nd  1st gear. The gear position is displayed on the gear position indicator. The gear position indicator shows the transaxle gear position. Before starting off, always check the gear position indicator to make sure that the transaxle is engaged in 1st or reverse, then depress the accelerator pedal. NOTE: • To downshift smoothly, the engine runs fast in some cases. This is done intentionally by the system and is not a malfunction. • When driving down a hill, downshift and use the engine braking appropriately. If necessary, continuous downshifting is possible. However, if downshifting more than 3 steps, gear shifting will take more time. • When the gear is shifting, a noise can be heard in some case. This is not a malfunction. • Be careful when accelerating, upshifting, downshifting or braking on a slippery surface. Sudden acceleration or engine braking could cause the vehicle to spin or skid. • To drive down a long or steep hill, reduce your speed and downshift. Remember, if you ride the brakes excessively, they may overheat and fail. • While driving the vehicle, do not shift the gearshift lever to “N” position. The engine brake may not work and you may get involved in an unexpected accident. If you return the gearshift lever from “N” to “M” because of unintended shifting, the gear position will be shifted according to the current vehicle speed. • Do not apply the parking brake while driving. Otherwise, it could cause a skid and you may get involved in an unexpected accident. 70 3-11 76MH1-74E OPERATING YOUR VEHICLE 76MH1-74E NOTICE • If the gearshift lever cannot shift into any position, or the gear is changed to “N” position automatically when the vehicle speed becomes less than 10 km/h (6 mph), there may be a systematic malfunction. In this case, ask your MARUTI SUZUKI dealer to inspect the Auto Gear Shift system as soon as possible. • The manual (M) mode does not upshift even if the engine speed reaches the rev-limit. • The system will not allow shifting up or down to a gear that would cause engine over-revving or under-revving. • If frequently driving at low speed using a high gear position, the life cycle of the clutch may be reduced. • Frequent downshifting (more than 3 positions consecutively) causes the reduction of transaxle life. Starting off: 1) Start the engine as instructed in “Starting the engine” in this section. 2) With your foot on the brake pedal, shift the gearshift lever to the “M” position. When the gearshift lever is shifted to the “M” position, the gear will be shifted to 1st. Before starting off, always make sure that the intended gear is engaged by checking the gear position indicator, then depress the accelerator pedal. NOTE: • If 1st gear cannot be engaged even though the gearshift lever has been shifted from the “N” to the “M” position, the system will re-try shifting automatically. This will take some time, noise may be heard from the gears, and shifting gear shock may occur. However, they do not indicate a malfunction. • The “N” indicator will flash, the depress brake pedal indicator will come on and a warning buzzer (long pulse sound) will sound if any of the following cases occur; – If you shift the gearshift lever from the “N” to the “M” position without depressing the brake pedal – If the system is unable to re-try shifting You should depress the brake pedal and shift the gearshift lever to “N” position, then shift to “M” position again a few seconds later. NOTICE Do not operate the system as described below. The life cycle of the clutch may be reduced. • Using the accelerator pedal to hold the vehicle on an uphill slope operation with the gearshift lever in the “M” or “D” position. If you perform this operation for a certain period of time, a warning buzzer will sound. • Shifting the gearshift lever to the “M”, “D” or “R” position while racing the engine. • Driving at low speed using a high gear. • Stopping on a slope using the creeping function. If you perform this operation for a certain period of time, a warning buzzer will sound. 3) Release the parking brake and brake pedal. Depress the accelerator pedal slowly for smooth starting. WARNING Always keep your foot on the brake pedal or pull up the parking lever while stopped with the engine running. These operations prevent the vehicle from starting due to unintended activation of the creeping function. 71 3-12 76MH1-74E OPERATING YOUR VEHICLE Starting off on an uphill/downhill slope: Uphill 1) Apply the parking brake firmly so that the vehicle does not roll backwards. 2) Shift the gearshift lever to the “M” position while depressing the brake pedal. Make sure that the gear position indicator in the instrumental cluster displays 1st gear. 3) Release the brake pedal and depress the accelerator pedal gradually, and when the vehicle starts to move, release the parking brake and depress the accelerator pedal to start off. 76MH1-74E Backing up After the vehicle has stopped completely, depress the brake pedal and shift the gearshift lever to the “R” position. Depress the accelerator pedal slowly as when starting off in 1st gear. Before backing up, make sure that reverse gear is selected by checking the gear position indicator. 76MH0A062 NOTICE On an uphill slope, never hold the vehicle at a stop using only the accelerator pedal or creeping function. If you perform this operation for a certain period of time, a warning buzzer will sound, and in some cases the engine will stall. This can also cause excessive damage to the clutch. Downhill 1) Depress the brake pedal and shift the gearshift lever to the “M” position. Check the gear position indicator to make sure that the gear is in 1st. 2) Release the brake pedal and depress the accelerator pedal slowly. Even though the accelerator pedal is not depressed, the clutch will be engaged when the vehicle speed increases. NOTE: • If reverse gear cannot be engaged even though the gearshift lever has been shifted from the “N” to the “R” position, the system will re-try shifting automatically. This will take some time, noise may be heard from the gears, and shifting gear shock may occur. However, they do not indicate a malfunction. • The “N” indicator will flash, the depress brake pedal indicator will come on and a warning buzzer (long pulse sound) will sound if any of the following cases occur; – If you shift the gearshift lever from the “N” to the “R” position without depressing the brake pedal – If the system is unable to re-try shifting You should depress the brake pedal and shift the gearshift lever to “N” position, then shift to “R” position again a few seconds later. • The system will not allow shifting to the “R” position if the vehicle speed is over about 3 km/h (2 mph). If the gearshift lever is operated under this condition, the “N” indicator in the instrument cluster will blink. However, when the vehicle speed drops below about 3 km/h (2 mph), the gear will be shifted to reverse. Make sure that the vehicle has stopped completely before shifting to the “R” position. NOTICE On a downhill slope, never hold the vehicle at a stop using only the accelerator pedal or the creeping function. If you perform this operation for a certain period of time, a warning buzzer will sound, and in some cases the engine will stall. This can also cause excessive damage to the clutch. Stopping The vehicle can be stopped by depressing the brake pedal regardless of the gear position. This is because the clutch is automatically disengaged to prevent the engine from stopping. • If the gearshift lever is in the “D” position, the gear will be downshifted to 1st when the vehicle stops. 72 3-13 76MH1-74E OPERATING YOUR VEHICLE 76MH1-74E • If the gearshift lever is in the “M” position, the gear will be downshifted to 1st when the vehicle stops. WARNING • When stopping, for example, at a traffic light, be sure to depress the brake pedal firmly. For your safety, apply the parking brake, too, when stopping on a hill. • When racing the engine, make sure that the gear is in the “N” position by checking the gear position indicator. If the accelerator is operated with the gear in any other position, the vehicle may move resulting in an unexpected accident. • Do not leave your vehicle unattended while the engine is running. • When leaving the vehicle, stop the engine and park the vehicle with a gear engaged. If you need to leave the vehicle with the engine running, apply the parking brakes firmly, and shift the gearshift lever to the “N” position. Otherwise, the vehicle may move unexpectedly and may cause an accident. NOTICE • On a slope, never hold the vehicle at a stop using only the accelerator pedal or the creeping function. If you perform this operation for a certain period of time, a warning buzzer will sound, and in some cases the engine will stall. This can also cause excessive damage to the clutch. • If the gearshift lever is operated more than necessary, the system may not allow operation of the gearshift lever for a certain period of time, and the gear may not be shifted appropriately. Therefore, do not operate the gearshift lever if not necessary. Parking Unlike an automatic transaxle, Auto Gear Shift does not have a parking position. The vehicle can be parked with the gearshift lever in any position. 1) Apply the parking brake firmly. 2) While depressing the brake pedal, shift the gearshift lever to the “R” position on a downhill slope, and to the 1st position in the drive (D) mode or the “M(1)” position in the manual (M) mode on an uphill slope and confirm the gear position by checking the gear position indicator. 3) Stop the engine. NOTE: • After the engine is stopped, the gear in the transaxle does not change even if you shift the gearshift lever in any position. Always shift the gearshift lever before stop the engine. • Check the transaxle gear position by looking at the gear position indicator, then turn the ignition switch off to stop the engine. Release the brake pedal after a few seconds. The gearshift lever will be locked in the position it was in when the ignition switch was turned off. WARNING • If the gear is not engaged properly and completely before the ignition switch is turned off, the vehicle may not be parked with the gear engaged. Always confirm the gear position by checking the gear position indicator when parking. • On a downhill slope, the gear should be put in reverse, and in 1st gear on an uphill slope. Otherwise, the vehicle may move, and cause an unexpected accident. If the gear is left in the “N” position, the vehicle cannot be parked with a gear engaged. Parking cancel Depress the brake pedal, turn the ignition switch to the “ON” position, and shift the gearshift lever to the “N” position. The gear will be disengaged. 73 3-14 76MH1-74E OPERATING YOUR VEHICLE Warning functions A warning buzzer will sound or the indicator will blink under the following conditions. Warning buzzer • The clutch is heated due to excessive load. • The creeping function is being activated for a long period of time. NOTICE In the above cases, pull over to the side of the road and stop the engine, and then ask your MARUTI SUZUKI dealer to inspect your vehicle. Otherwise, the clutch disc may be damaged. • The ignition switch is turned to the “LOCK” position with the gear in 2nd, 3rd, 4th or 5th. In this case, turn the ignition switch to the “ON” position and shift the gearshift lever in the “N” position, shift it to the “D” or “M” or “R” position, then turn the ignition switch to “LOCK”. • During a stop, the driver’s door is opened with the gearshift lever in the “R”, “D” or “M” position while the engine is running. “N” indicator blinking When the gear indicator lamp blinks “N”, you should depress the brake pedal and shift the gearshift lever to “N” position. “1st” indicator blinking 76MH1-74E When the gear indicator lamp blinks “1st”, you should depress the brake pedal and shift the gearshift lever to “N” position, then shift to “D” or “M” position again a few seconds later. “R” indicator blinking When the gear indicator lamp blinks “R”, you should depress the brake pedal and shift the gearshift lever to “N” position, then shift to “R” position again a few seconds later. Braking EXAMPLE and the stopping point, and slow down gradually. WARNING If water gets into the brake drums, brake performance may become poor and unpredictable. After driving through water or washing the underside of the vehicle, test the brakes while driving at a slow speed to see if they have maintained their normal effectiveness. If the brakes are less effective than normal, dry them by repeatedly applying the brakes while driving slowly until the brakes have regained their normal effectiveness. Power-Assisted Brakes 60G165S The distance needed to bring any vehicle to a halt increases with the speed of the vehicle. The braking distance needed, for example, at 60 km/h (37 mph) will be approximately 4 times greater than the braking distance needed at 30 km/h (19 mph). Start to brake the vehicle when there is plenty of distance between your vehicle Your vehicle has power-assisted brakes. If power assistance is lost due to a stalled engine or other failures, the system is still fully operational on reserve power and you can bring the vehicle to a complete stop by pressing the brake pedal once and holding it down. The reserve power is partly used up when you depress the brake pedal and reduces each time the pedal is pressed. Apply smooth and even pressure to the pedal. Do not pump the pedal. 74 3-15 76MH1-74E OPERATING YOUR VEHICLE 76MH1-74E WARNING Even without reserve power in the brake system, you can still stop the vehicle by pressing the brake pedal harder than normally required. However, the stopping distance may be longer. Brake Assist System (if equipped) When you slam the brakes on, the brake assist system judges as an emergency stop and provides more powerful braking for a driver who cannot hold down the brake pedal firmly. NOTE: If you quickly and forcefully depress the brakes, you may hear a clicking sound in the brake pedal. This is normal and indicates that the brake assist system is activated properly. Anti-Lock Brake System (ABS) (if equipped) ABS will help you avoid skidding by electronically controlling braking pressure. It will also help you maintain steering control when braking on slippery surfaces or when braking hard. The ABS works automatically, so you do not need any special braking technique. Just push the brake pedal down without pumping. The ABS will operate whenever it senses that the wheels are locking up. You may feel the brake pedal moves a little while the ABS is operating. NOTE: The ABS will not work if vehicle speed is under about 10 km/h (6 mph). WARNING • On some types of loose surfaces (such as gravel, snow-covered roads, etc.) the stopping distance required for an ABS-equipped vehicle may be slightly greater than for a comparable vehicle with a conventional brake system. With a conventional brake system, skidding tires are able to “plow” the gravel or snow layer, shortening the stopping distance, ABS minimizes this resistance effect. Allow for extra stopping distance when driving on loose surfaces. • On regular paved roads, some drivers may be able to obtain slightly shorter stopping distances with conventional brake systems than with ABS. • In both of the above conditions, ABS will still offer the advantage of helping you maintain directional control. However, remember that ABS will not compensate for bad road or weather conditions or poor driver judgment. Use good judgment and do not drive faster than conditions will safely allow. (1) (2) 63J081 (1) ABS warning light (2) Brake system warning light WARNING • If the ABS warning light (1) on the instrument panel comes on and stays on while driving, there may be a problem with the ABS system. Ask your MARUTI SUZUKI dealer to inspect the ABS system immediately. If the ABS system becomes inoperative, the brake system will function as an ordinary brake system that has no ABS. (Continued) 75 3-16 76MH1-74E OPERATING YOUR VEHICLE 76MH1-74E How the ABS Works WARNING (Continued) • If the ABS warning light (1) and the Brake system warning light (2) on the instrument panel simultaneously stays on or comes on when driving, both anti-lock function and rear brake force control function (proportioning valve function) of the ABS system may have failed. If so, the rear wheels may easily skid or the vehicle can even spin in the worst case when braking on a slippery road or when hard braking even on a dry paved road. Ask your MARUTI SUZUKI dealer to inspect the ABS system immediately. Drive carefully, avoiding hard braking as much as possible. A computer continuously monitors wheel speed. The computer compares the changes in wheel speed when braking. If the wheels slow suddenly, indicating a skidding situation, the computer will change braking pressure several times each second to prevent the wheels from locking. When you start your vehicle after a stop you may hear a momentary motor noise as the system checks itself. WARNING The ABS may not work properly if tires or wheels other than those specified in the owner’s manual are used. This is because the ABS works by comparing changes in wheel speed. When replacing tires or wheels, use only the size and type specified in this owner’s manual. 76 3-17 76MH1-74E 76MH1-74E DRIVING TIPS DRIVING TIPS Running-in ........................................................................... 4-1 Catalytic Converter ............................................................. 4-1 Improving Fuel Economy ................................................... 4-2 Highway Driving .................................................................. 4-3 Driving on Hills .................................................................... 4-3 Driving on Slippery Roads ................................................. 4-3 Driving on Wet Roads...........................................................4-4 Do’s and Dont’s for Safe Driving.........................................4-5 Margin for Safety...................................................................4-7 77 76MH1-74E DRIVING TIPS 76MH1-74E Running-in Catalytic Converter NOTICE 52D078S WARNING • Wear Your Seat Belts at All Times. Even though air bags are equipped at the front seating positions, the driver and all passengers should be properly restrained at all times, using the seat belts provided. Refer to the “Seat Belts and Child Restraint Systems” section for instructions on proper use of the seat belts. • Never drive while under the influence of alcohol or other drugs. Alcohol and drugs can seriously impair your ability to drive safely, greatly increasing the risk of injury to yourself and others. You should also avoid driving when you are tired, sick, irritated, or under stress. The future performance and reliability of the engine depends on the care and restraint exercised during its early life. It is especially important to observe the following precautions during the initial 960 km (600 miles) of vehicle operation. • After starting, do not race the engine. Warm it up gradually. • Avoid prolonged vehicle operation at a constant speed. Moving parts will break in better if you vary your speed. • Start off from a stop slowly. Avoid full throttle starts. • Avoid hard braking, especially during the first 320 km (200 miles) of driving. • Do not drive slowly with the transaxle in a high gear. • Drive the vehicle at moderate engine speeds. • Do not tow a trailer during the first 960 km (600 miles) of vehicle operation. 80G106 The purpose of the catalytic converter is to minimize the amount of harmful pollutants in your vehicle’s exhaust. Use of leaded fuel in vehicles equipped with catalytic converters is prohibited, because lead deactivates the pollutant-reducing components of the catalyst system. The converter is designed to last the life of the vehicle under normal usage and when unleaded fuel is used. No special maintenance is required on the converter. However, it is very important to keep the engine properly tuned. Engine misfiring, which can result from an improperly tuned engine, may cause overheating of the catalyst. This may result in permanent heat damage to the catalyst and other vehicle components. 78 4-1 76MH1-74E DRIVING TIPS 76MH1-74E Avoid “fast” starts Fast starts away from lights or stop signs will consume fuel unnecessarily and shorten engine life. Start off slowly. NOTICE To avoid damaging catalyst or other vehicle damage: • Maintain the engine in the proper operating condition. • In the event of an engine malfunction, particularly one involving engine misfiring or other apparent loss of performance, have the vehicle serviced promptly. • Do not turn off the engine or interrupt the ignition when the transaxle is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the vehicle, or coasting down a hill. • Do not idle the engine with any spark plug wires disconnected or removed, such as during diagnostic testing. • Do not idle the vehicle for prolonged periods if idling seems rough or there are other malfunctions. • Do not allow the fuel tank to get near the empty level. • Avoid driving your vehicle at excessively high engine speed in or around the red zone of the tachometer (if equipped). Avoid unnecessary stops Avoid unnecessary deceleration and stopping. Try to maintain a slow, steady speed whenever possible. Slowing down and then accelerating again uses more fuel. 54G584S WARNING Keep a steady cruising speed Keep as constant a speed as road and traffic conditions will permit. Keep the air cleaner clean Be careful in areas where you park and drive; the catalytic converter and other exhaust components can get very hot. As with any vehicle, do not park or operate this vehicle in areas where combustible materials such as dry grass or leaves can come in contact with a hot exhaust system. Improving Fuel Economy The following instructions will help you improve fuel economy. Avoid excessive idling If you are to wait for more than a minute while you are parked, stop the engine and start it again later. When warming up a cold engine, do not allow the engine to idle or apply full throttle until the engine has reached operating temperature. Allow the engine to warm up by driving. EXAMPLE 60A183S If the air cleaner is clogged with dust, there will be greater intake resistance, resulting in decreased power output and increased fuel consumption. 79 4-2 76MH1-74E DRIVING TIPS Keep weight to a minimum The heavier the load, the more fuel the vehicle consumes. Take out any luggage or cargo when it is not necessary. Keep tire pressures correct Underinflation of the tires can waste fuel due to increased running resistance of the tires. Keep your tires inflated to the correct pressure shown on the label on the driver’s side door or the driver’s door lock pillar. Highway Driving When driving at highway speeds, pay attention to the following: • Stopping distance progressively increases with vehicle speed. Apply the brakes far enough ahead of the stopping point to allow for the extra stopping distance. • On rainy days, “Hydroplaning” can occur. “Hydroplaning” is the loss of direct contact between the road surface and the vehicle’s tires due to a water film forming between them. Steering or braking the vehicle while “Hydroplaning” can be very difficult, and loss of control can occur. Keep speed down when the road surface is wet. • At high speeds, the vehicle may be affected by side winds. Therefore, reduce speed and be prepared for unexpected buffeting, which can occur at the exits of tunnels, when passing by a cut of a hill, or when being overtaken by large vehicles, etc. 76MH1-74E Driving on Hills NOTICE When descending a down hill, NEVER turn the ignition key to the “LOCK” position. Emission control system damage may result. Driving on Slippery Roads R - N M D + 76MH0A063 • When climbing steep hills, the vehicle may begin to slow down and show a lack of power. If this happens, you should shift to a lower gear so that the engine will again be operating in its normal power range. Shift rapidly to prevent the vehicle from losing momentum. • When driving down a hill, the engine should be used for braking by shifting into a lower gear. WARNING Try not to hold the brake pedal down too long or too often while going down a steep or long hill. This could cause the brakes to overheat, resulting in reduced braking efficiency. Failure to take this precaution could result in loss of vehicle control. 60G089S Under wet road conditions you should drive at a lower speed than on dry roads due to possible slippage of tires during braking. When driving on icy, snow-covered, or muddy roads, reduce your speed and avoid sudden acceleration, abrupt braking, or sharp steering movements. Tire Chains (if equipped) Tire chains should only be used if they are needed to increase traction or are required by law. Make sure that the chains you use 80 4-3 76MH1-74E DRIVING TIPS 76MH1-74E are the correct size for your vehicle’s tires. Also make sure that there is enough clearance between the fenders and the chains as installed on the tires. Install the chains on the front tires tightly, according to the chain manufacturer’s instructions. Retighten the chains after driving about 1.0 km (1/2 mile) if necessary. With the chains installed, drive slowly. NOTICE • If you hear the chains hitting against the vehicle body while driving, stop and tighten them. • If your vehicle is equipped with full wheel caps, remove the wheel caps before installing the chains or the wheel caps can be damaged by the chain bands. 2) If your vehicle remains stuck after a few minutes of rocking, get another vehicle to pull your vehicle out. WARNING Do not allow anyone to stand near the vehicle when you are rocking it, and do not spin the wheels faster than an indicated 40 km/h (25 mph) on the speedometer. Personal injury and/ or vehicle damage may result from spinning the wheels too fast. NOTICE Do not continue rocking the vehicle for more than a few minutes. Prolonged rocking can cause engine overheating or transaxle damage. If Your Vehicle Gets Stuck If your vehicle gets stuck in snow, mud, or sand, follow the directions below: 1) Shift the transaxle back and forth between a forward range (or first gear for manual transaxle) and reverse. This will create a rocking motion which may give you enough momentum to free the vehicle. Press gently on the accelerator to keep wheel spinning to a minimum wheel rpm. Remove your foot from the accelerator while shifting. Do not race the engine. Excessive wheel spin will cause the tires to dig deeper, making it more difficult to free the vehicle. 54G638S DRIVING ON WET ROADS NOTICE • When driving on wet roads, avoid driving through large amount of standing water on the road. Large amount of water entering the engine compartment may cause damage to the engine and or electrical components. • If stuck in deep water, do not start till water level drops. • Water is incompressible substance, water inside engine is harmful to the engine. WARNING In addition to following the driving tips in this section, it is important to observe the following precautions. • Make sure your tires are in good condition and always maintain the specified tire pressure. Refer to “Tires” in the “INSPECTIONAND MAINTENANCE” • Di not use tires other than those specified by MARUTI SUZUKI.Never use different sizes or types of tires on the front and rear wheels. For information regarding the specified tires, refer to the Tire Information Label located on the driver’s door lock pillar (Continued) 81 4-4 76MH1-74E DRIVING TIPS 76MH1-74E WARNING (Continued) • Never use oversized tires or special shock absorbers and springs to raise (jack up) your vehicle. This will change the handling characteristics. Oversized tires may also rub against the fender over bumps, causing vehicle damage or tire failure. • After driving through water, test the brakes while driving at a slow speed to see if they have maintained their normal effectiveness. If the brakes are less effective than normal, dry them by repeatedly applying the brakes while driving slowly until the brakes have regained their normal effectiveness. Do’s and Dont’s for Safe Driving Exercise care in handling your vehicle. Be conscious of not only your own safety but also the safety of others on the road, and thus enjoy the best and most comfortable driving experience. This section contains basic rules for safe driving. Read it carefully for good understanding of the content so that you can enjoy safe and pleasant driving in your Maruti Suzuki vehicle. 72F-08-002 72F-08-002 Starting 1) Adjust the driver’s seat for the proper driving posture. 2) Adjust the rear view mirror so as to obtain the best possible rear view. 3) Before moving off, look forward and back to confirm safety. 4) Don’t start quickly, since it is dangerous and wastes fuel. General driving 1) Be sure to stop before the stop light and stop sign. When moving into the intersection without any traffic lights or signs, drive slowly to confirm safety. 2) Always follow other vehicles at a safe distance in order to prevent a rear-end collision, in case the vehicle ahead make a sudden stop. 3) Turn ON the turn signal at least 30 meters before making a turn or changing the lane so as not to be hit from behind. 4) Before entering a corner, decelerate to a safe speed. Don’t apply brakes during cornering, or a cornering skid may occur. 5) When overtaking other vehicles, watch out for the oncoming vehicle and carefully confirm the safety. 6) Don’t attempt zigzag driving which will hinder your control over the vehicle and cause an accident. 82 4-5 76MH1-74E DRIVING TIPS 76MH1-74E 72F-08-011 Braking 1) Use the parking brake when parking your vehicle and shift the gear shift lever into the first gear or reverse gear position for the sake of safety. 2) Don’t use hand-braking unless unavoidable. It causes the vehicle to skid and a rear-end collision occur. It is especially dangerous when the tyres are worn, for they allow a larger skid. 72F-08-012 72F-08-015 Use foot brake in three stages 1. Warn the vehicle behind you 2. Gradually apply the brake. 3. Bring the vehicle to a halt. 3) When driving on a downhill, try not to apply the brake but use the engine brake effectively. Overuse of the foot-brake may result in total brake failure. 4) Avoid reckless high speed driving and try to drive at a safe speed suitable for the road conditions while maintaining a constant speed. 5) The higher the speed, the narrower the driver’s visual range becomes. In such a state, it is difficult to anticipate any hazard and the driver feels much fatigued. 6) Never do sharp handling during high speed driving. You will lose your control over your vehicle. 7) When overtaking or changing the lane while driving at a high speed, keep an ample vehicle-to-vehicle distance. 83 4-6 76MH1-74E DRIVING TIPS 76MH1-74E Long distance driving 1) Be sure to perform safety checks before starting a trip. 2) Take rest at certain intervals to prevent an accident which may occur when you are sleepy or tired. when the windshield glass is dry or the wiper blade and glass may get damaged. Margin For Safety It is important to allow yourself a margin for safety during driving so that you can cope with erroneous or unexpected driving of other drivers. For that, observe the following. • Drive at a safe speed. • Maintain a sufficient distance between your vehicle and the vehicle ahead. • Don’t force yourself to overtake other vehicles. • Don’t make quick start, hard steering or sudden stops. • Allow an ample time in the driving schedule. • Observe traffic rules and regulations. 72F-08-021 Conclusion A perfect driver does not exist. The endeavor of every motorist should be to strive for perfection. Safety consciousness not only ensures your safety and the safety of other road users, it also helps reduce the wear and tear on your vehicle, prolongs its life, gives more mileage and ensures a comfortable driving experience. Follow the do’s and don’ts listed, and driving will never be the same again. 72F-08-020 Night time driving 1) Drive more slowly at night than in the daytime, for the visual range is restricted at night. 2) Don’t overtake other vehicles at night. Darkness bothers your sense of speed and hinders your judgment on the vehicle-to-vehicle distance. 3) Don’t use the high headlight beam unless its use is inevitable. Its dazzle may blitz the driver of the oncoming vehicle, thus causing an accident. 4) Always keep the window glasses clean. Don’t operate the windshield wiper 72F-08-022 84 4-7 76MH1-74E 76MH1-74E OTHER CONTROLS AND EQUIPMENT OTHER CONTROLS AND EQUIPMENT Fuel Filler Cap ..................................................................... 5-1 Engine Hood ........................................................................ 5-2 Sun Visor ............................................................................. 5-3 Interior Light ........................................................................ 5-4 Accessory Socket ............................................................... 5-5 AUX/USB Socket (if equipped) ........................................... 5-5 Assist Grips (if equipped) .................................................. 5-5 Glove Box ............................................................................ 5-6 Cup Holder and Storage Area ............................................ 5-6 Floor Mats (if equipped) ..................................................... 5-7 Luggage Compartment Hooks ........................................... 5-8 Luggage Compartment Cover (if equipped) ..................... 5-8 Frame Hooks ....................................................................... 5-9 Manual Heating and Air Conditioning System ................. 5-10 Radio Antenna ..................................................................... 5-13 Audio System (if equipped) ................................................ 5-14 85 76MH1-74E OTHER CONTROLS AND EQUIPMENT Fuel Filler Cap 76MH1-74E The fuel filler cap is located on the left rear side of the vehicle. The fuel filler door can be unlocked by pulling up the opener lever located on the outboard side of the driver’s seat and locked by simply closing the door. Open EXAMPLE Close (1) EXAMPLE 76MH0A065 76MH0A064 EXAMPLE EXAMPLE 68KN048 To remove the fuel filler cap: 1) Open the fuel filler door. 2) Remove the cap by turning it counterclockwise. CAUTION Remove the fuel filler cap slowly. The fuel may be under pressure and may spray out, causing injury. NOTE: If the cap holder (1) is equipped with the fuel filler door, hold the fuel filler cap when refueling. To reinstall the fuel filler cap: 1) Turn the cap clockwise until you hear several clicks. 2) Close the fuel filler door. WARNING Fuel is extremely flammable. Do not smoke when refueling, and make sure there are no open flames or sparks in the area. 74LHT0511 86 5-1 76MH1-74E OTHER CONTROLS AND EQUIPMENT 76MH1-74E WARNING If you need to replace the fuel cap, use a Maruti genuine cap. Use of an improper cap can result in a malfunction of the fuel system or emission control system. It may also result in fuel leakage in the event of an accident. Engine Hood EXAMPLE 76MH0A067 76MH0A068 2) Push the under-hood release lever up with your finger, as shown in the illustration. While pushing the lever, lift up the engine hood. 3) While holding the hood, pull the prop rod out from the holding clip, then insert the end of the rod into the designated hole in the hood. CAUTION The release lever can be hot enough to burn your finger right after driving. Touch the lever after it becomes cool enough. 76MH0A066 To open the engine hood: 1) Pull the hood release handle located on the outboard side of the driver’s side. This will disengage the engine hood lock halfway. NOTICE Make sure that the wiper arms are not raised before you lift up the engine hood to avoid damaging the wiper arms and the engine hood. CAUTION • The prop rod can be hot enough to burn your finger right after driving. Touch the rod after it becomes cool enough. • Insert the end of the rod into the hole securely. If the rod drops off, your body may be caught in the hood. • The rod may drop off when the hood is hit by a wind. Be careful on windy days. 87 5-2 76MH1-74E OTHER CONTROLS AND EQUIPMENT To close the engine hood: 1) Lift the hood up slightly and remove the prop rod from the hole. Put the prop rod back to the holding clip. EXAMPLE 76MH1-74E CAUTION NOTICE To avoid injury, be sure no part of the occupant’s body such as hands or head is in the path of the hood when closing it. When unhooking and hooking a sun visor, be sure to handle it by the hard plastic parts or the sun visor can be damaged. Card holder (if equipped) NOTICE Pressing the hood from above may damage the hood. EXAMPLE Sun Visor 76MS014 2) Lower the hood to about 20 cm above the hood latch, then let it drop down. Make sure the hood is securely latched after closing. WARNING Make sure the hood is fully closed and latched before driving. If it is not, it can fly up unexpectedly during driving, obstructing your view and resulting in an accident. (1) 67LH064 (1) Card holder EXAMPLE 79J161 The sun visors can be pulled down to block glare coming through the windshield, or they can be unhooked and turned to the side to block glare coming through the side window. You can put a card in the card holder (1) on the back of the sun visor. NOTICE When you park your vehicle outdoors in direct sunlight or in hot weather, do not leave plastic cards in the holder. The heat may distort them. 88 5-3 76MH1-74E OTHER CONTROLS AND EQUIPMENT 76MH1-74E Interior Light Vanity mirror (if equipped) ON (a) The light comes on and stays on regardless of whether the door is open or closed. Type A (2) EXAMPLE (c) (b) DOOR (b) The light comes on when the door is opened. After closing all doors, the light will remain on for about 15 seconds and then fade out. If you insert the key into the ignition switch during that time, the light will start to fade out immediately. After removing the key from the ignition switch, the light will turn on for about 15 seconds and then fade out. (a) EXAM74LHT0532 (2) Vanity mirror There is a vanity mirror (2) on the back of the sun visor. WARNING • Do not use the mirror while driving your vehicle or could lose control of the vehicle. • When using the vanity mirror, do not move too close to a front air bag (if equipped) location or lean against it. If the front air bag is accidentally inflated, it could hit you hard. 61MM0A107 Type B NOTE: To save the battery, about 15 minutes after any of the doors is left open, the light will turn off automatically. OFF (c) The light remains off even when the door is opened. EXAMPLE (c) (b) (a) 76MH0A138 This light switch has three positions which function as described below: EXAMPLE 76MH0A069 89 5-4 76MH1-74E OTHER CONTROLS AND EQUIPMENT NOTE: The number of doors involved in the lighting operation of the interior light depends on the vehicle specification. If there is a switch (rubber projection) at the door opening as shown, the door is involved in the lighting operation. The tailgate is also involved in this operation even without the rubber projection. 76MH1-74E NOTICE NOTICE Use of inappropriate electrical accessories can cause damage to your vehicle’s electrical system. Make sure that any electrical accessories you use are designed to plug into this type of socket. Always close the lid when not in use, since entry of foreign material, dust, water, conductive liquids may damage the audio system or USB device. Assist Grips (if equipped) AUX/USB Socket (if equipped) Accessory Socket (if equipped) 76MH0A072 EXAMPLE 76MH0A071 EXAMPLE 76MH0A070 The accessory socket will work when the ignition switch is in the “ACC” or “ON” position. This socket can be used to provide 12 volt/120 watt power for electrical accessories. Connect your portable digital music player, etc. to this socket to enjoy music through the vehicle’s audio system using it as a source. Refer to “Audio System” in this section. Assist grips are provided for convenience. NOTICE To avoid damaging the assist grip and the molded headlining, do not hang down the assist grip. 90 5-5 76MH1-74E OTHER CONTROLS AND EQUIPMENT Glove Box Cup Holder and Storage Area EXAMPLE (6) (4) (1) EXAMPLE 76MH0A073 To open the glove box, pull the latch lever. To close it, push the lid until it latches securely. (2) (3) (4) (5) (6) WARNING Never drive with the glove box lid open. It could cause injury if an accident occurs. 76MH0A074 (1) Instrument panel pocket (driver’s side) (2) Instrument panel pocket (center) (3) Front cup holders (4) Front door pocket (5) Rear cup holder (6) Rear door pocket 91 5-6 76MH1-74E OTHER CONTROLS AND EQUIPMENT Instrument Panel Pocket (driver’s side) (1) / Instrument Panel Pocket (center) (2) 76MH1-74E Floor Mats (if equipped) Rear Cup Holder (5) EXAMPLE EXAMPLE WARNING Do not place any objects which may fall out from the pocket when the vehicle is moving. Failure to take the precaution may result in an object interfering with the pedals and causing a loss of vehicle control or an accident. Front Cup Holders (3) WARNING Failure to take the precautions listed below could cause personal injury or vehicle damage. • Be careful when you are using the cup holders to hold a cup containing hot liquid. Spilling out hot liquid can cause burn injury. • Do not use the cup holders to hold sharp-edged, hard, or breakable objects. Objects in the cup holders may be thrown about during a sudden stop or impact, and could cause personal injury. • Be careful not to spill liquid or insert any foreign materials into the moving part of the gearshift lever, or any electrical components. Liquid or foreign materials may damage these parts. 76MH0A075 Open the top to use the cup holder. Rear Door Pocket (6) This pocket is provided for holding light and small items. Bottle holder You should hold a bottle with a cap in the holder. 68LM554 To prevent the driver’s side floor mat from sliding forward and possibly interfering with the operation of the pedals, Maruti genuine floor mats are recommended. Whenever you put the driver’s side floor mat back in the vehicle after it has been removed, be sure to hook the floor mat grommet(s) to the fastener(s) and position the floor mat properly in the footwell. When you replace the floor mats in your vehicle with a different type such as allweather floor mats, we highly recommend using Maruti genuine floor mats for proper fitting. 92 5-7 76MH1-74E OTHER CONTROLS AND EQUIPMENT 76MH1-74E WARNING NOTICE Failure to take the following precautions may result in the driver’s side floor mat interfering with the pedals and causing a loss of vehicle control or an accident. • Make sure that the floor mat grommet(s) is(are) hooked to the fastener(s). • Never place additional floor mats on top of the existing floor mat. WARNING To avoid breaking the hook, do not hang items heavier than following weight. Shopping hook: 1 kg (2.2 lbs) Luggage Compartment Cover (if equipped) Do not carry items on top of the luggage compartment cover, even if they are small and light. Objects on top of the cover could be thrown about in an accident, causing injury, or could obstruct the driver’s rear view. NOTICE To avoid damaging the luggage compartment cover: • Do not push down on it or lean on it. • Handle it carefully when installing or removing. Luggage Compartment Hooks Shopping Hook EXAMPLE EXAMPLE 76MH0A076 Luggage or other cargo placed in the luggage compartment is hidden from view by a luggage compartment cover. 76MH0A104 You can hang the shopping bag or other suitable objects on the hook. This hook is not designed for large or heavy items. 93 5-8 76MH1-74E OTHER CONTROLS AND EQUIPMENT 76MH1-74E Frame Hooks NOTICE Front WARNING When you use the frame hook (1), avoid the driving that gives significant physical shock on hook. Such operation can damage the hook, or the vehicle body. Do not accelerate suddenly. Rear Do not use the frame hooks to tow another vehicle or to have your vehicle towed on the road or highway. The hook (2) is designed for use in emergency situations only, such as if your vehicle or another vehicle gets stuck in deep mud or snow. NOTICE When you use the frame hook (2), avoid the driving that gives significant physical shock on hook. Such operation can damage the hook, the vehicle body or the drive system. (1) 76MH0A077 The frame hook (1) is provided on the front of the vehicle for use in emergency situations and train shipping purposes only. To tow your vehicle on the road or highway, follow the instruction of “Towing” in “EMERGENCY SERVICE” section. WARNING Do not use the frame hooks to tow another vehicle or to have your vehicle towed on the road or highway. The hook (1) is designed for use in emergency situations only, such as if your vehicle or another vehicle gets stuck in deep mud or snow. • Do not accelerate suddenly. • Do not tow the vehicle heavier than your vehicle. (2) EXAMPLE 76MH0A078 The frame hook (2) is provided on the rear of the vehicle for use in emergency situations and train/sea shipping purposes only. To tow your vehicle on the road or highway, follow the instruction of “Towing” in “EMERGENCY SERVICE” section. 94 5-9 76MH1-74E OTHER CONTROLS AND EQUIPMENT 76MH1-74E Manual Heating and Air Conditioning System (if equipped) When “Open”, air comes out regardless of the air flow selector position. This is used to select the temperature by turning the selector. Center outlet Blower speed selector (2) This is used to turn on the blower and to select blower speed by turning the selector. (1) Air outlet (1) EXAMPLE Air flow selector (3) (c) 1 1 2 2 (b) 4 3 (d) 76MH0A081 3 5 Move the knob (1) vertically or horizontally to adjust the direction of airflow as desired. (a) Description of Controls 5 76MH0A080 (2) 1. Windshield defroster outlet 2. Side defroster outlet 3. Side outlet 4. Center outlet 5. Front floor outlet Side outlet (e) 61MM0A019 This is used to select one of the functions described below. (5) Ventilation (a) 1 0 2 3 4 76MH0A083 (3) (4) (1) 76MH0A082 Temperature-controlled air comes out of the center and side air outlets. Temperature selector (1) 76MH0A118 95 5-10 76MH1-74E OTHER CONTROLS AND EQUIPMENT Bi-level (b) 76MH1-74E Heat & defrost (d) Air intake selector (4) (g) (f) 76MH0A084 76MH0A087 76MH0A089 Temperature-controlled air comes out of the floor outlets and cooler air comes out of the center and side outlets. When the temperature selector (1) is in the fully COLD position or fully HOT position, however, the air from the floor outlets and the air from the center and side outlets will be the same temperature. Temperature-controlled air comes out of the floor outlets, the windshield defroster outlets, the side defroster outlets and the side outlets. This selector is used to select the following modes. Defrost (e) Heat (c) 76MH0A088 76MH0A085 Temperature-controlled air comes out of the floor outlets and the side outlets, also comes out of the windshield defroster outlets and also comes slightly out of the side defroster outlets. Temperature-controlled air comes out of the windshield defroster outlets, the side defroster outlets and the side outlets. Fresh Air (f) When this mode is selected by moving the lever to right, outside air is used. Recirculated Air (g) When this mode is selected by moving the lever to left, outside air is shut out and inside air is recirculated. This mode is suitable when driving through dusty or polluted air such as in a tunnel, or when attempting to quickly cool down the interior. NOTE: If you select “RECIRCULATED AIR” for an extended period of time, the air in the vehicle can become contaminated. Therefore, you should occasionally select “FRESH AIR”. 96 5-11 76MH1-74E 76MH1-74E Air conditioning switch (5) To turn on the air conditioning system, set the blower speed selector to a position other than “OFF” and push in the “A/C” switch. With this “A/C” switch operation, a indicator light will come on when the air conditioning system is on. To turn off the air conditioning system, push the “A/C” switch again. During operation of the air conditioner, you may notice slight changes in engine speed. These changes are normal, the system is designed so that the compressor turns on or off to maintain the desired temperature. Less operation of the compressor results in better fuel economy. System Operating Instructions Natural ventilation Select “VENTILATION” and “FRESH AIR”, the temperature selector to the desired temperature position, and the blower speed selector to “OFF”. Fresh air will flow through the vehicle during driving. Forced ventilation The control settings are the same as for natural ventilation except you set the blower speed selector to a position other than “OFF”. Normal heating (using outside air) Select “HEAT” and “FRESH AIR”, the temperature selector to the desired temperature position and the blower speed selector OTHER CONTROLS AND EQUIPMENT to the desired blower speed position. Setting the blower speed selector to a higher blower speed position increases heating efficiency. You can switch the air intake selector to either “FRESH AIR” or “RECIRCULATED AIR” as you desire. Choosing “RECIRCULATED AIR” increases cooling efficiency. Quick heating (using recirculated air) The control settings are the same as for normal heating except you select “RECIRCULATED AIR”. If you use this heating method for an extended period of time, the air in the vehicle can become contaminated and the windows can become misty. Therefore, use this method only for quick heating and change to the normal heating method as soon as possible. Quick cooling (using recirculated air) The control settings are the same as for normal cooling except you select “RECIRCULATED AIR” and the highest blower speed. Head cooled/Feet warmed heating Select “BI-LEVEL” and “FRESH AIR”, the temperature selector to the desired temperature position, and the blower speed selector to the desired blower speed position. Unless the temperature selector is in the fully COLD position or fully HOT position, the air that comes out of the center and side outlets will be cooler than the air that comes out of the floor outlets. Normal cooling Set the air flow selector to “VENTILATION”, the temperature selector to the desired temperature position and the blower speed selector to the desired blower speed position, and turn on the “A/ C” switch. Setting the blower speed selector to a higher blower speed position increases cooling efficiency. NOTE: • To turn on the air conditioning system, push in the “A/C” switch and set the blower speed selector to a position other than “OFF”. With this “A/C” switch operation, an indicator light will come on when the air conditioning system is on. To turn off the air conditioning system, push the “A/C” switch again. • During operation of the air conditioner, you may notice slight changes in engine speed. These changes are normal, the system is designed so that the compressor turns on or off to maintain the desired temperature. Less operation of the compressor results in better fuel economy. NOTE: • If you select “RECIRCULATED AIR” for an extended period of time, the air in the vehicle can become contaminated. Therefore, you should occasionally select “FRESH AIR”. • If your vehicle has been left in the sun with the windows closed, it will cool 97 5-12 76MH1-74E OTHER CONTROLS AND EQUIPMENT faster if you open the windows briefly while you operate the air conditioner with the air intake selector at “FRESH AIR” and the blower at high speed. Dehumidifying Set the air flow selector to a desired air flow selector position, the temperature selector to the desired temperature position and the blower speed selector to the desired blower speed position. Also select “FRESH AIR” and turn on the “A/C” switch. NOTE: Because the air conditioner dehumidifies the air, turning it on will help keep the windows clear, even when blowing heated air using the “DEFROST” or “HEAT & DEFROST” functions. 76MH1-74E • set the blower speed selector to HIGH, • adjust the temperature selector to the HOT end, • turn on the “A/C” switch, and • adjust the side outlets so the air blows on the side windows. If you do not use the air conditioner for a long period, such as during winter, it may not give the best performance when you start using it again. To help maintain optimum performance and durability of your air conditioner, it needs to be run periodically. Operate the air conditioner at least once a month for one minute with the engine idling. This circulates the refrigerant and oil and helps protect the internal components. NOTICE 76MH0A090 NOTE: If you need maximum defrosting: • set the air flow selector to “DEFROST”, EXAMPLE Maintenance NOTE: Your vehicle uses the air conditioning refrigerant HFC-134a, commonly called “R-134a”. R-134a replaced R-12 around 1993 for automotive applications. Other refrigerants are available, including recycled R-12, but only R-134a should be used in your vehicle. EXAMPLE Radio Antenna Using the wrong refrigerant may damage your air conditioning system. Use R-134a only. Do not mix or replace the R-134a with other refrigerants. 68KN028 The radio antenna on the roof is removable. To remove the antenna, turn it counterclockwise. To reinstall the antenna, turn it clockwise firmly by hand. NOTICE To avoid damage to the radio antenna: • Remove the antenna when using an automatic car wash. • Remove the antenna when the antenna hits anything such as a low ceiling in a parking garage or putting a car cover over your vehicle. 98 5-13 76MH1-74E OTHER CONTROLS AND EQUIPMENT 76MH1-74E Audio System (if equipped) Safety Information WARNING If you pay extended attention to operating the audio system or viewing the audio system display while driving, an accident can occur. If you set the sound volume too loud, it could prevent you from being aware of road and traffic conditions. • Keep your eyes on the road and your mind on the drive. Avoid paying extended attention to operating the audio system or viewing the audio system display. • Familiarize yourself with the audio system controls and operation of the audio system before driving. • Preset your favorite radio stations before driving so that you can quickly tune to them using the presets. • Set the sound volume to a level that will allow you to continue to be aware of road and traffic conditions while driving. Notes on Discs on the disc, wipe it off with a soft cloth. If condensation forms on the optical parts of the player, do not use the player for about one hour. This will allow the condensation to disappear normally. • Driving on extremely bumpy roads which cause severe vibrations may cause sound to skip. • This unit uses a precision mechanism. Even in the event that trouble arises, never open the case, disassemble the unit, or lubricate the rotating parts. Please bring the unit to an authorized MARUTI SUZUKI dealer. Cautions on Handling (A) This unit has been designed specifically for playback of compact discs bearing mark (A) shown above. No other discs can be played. Removing the disc Proper way to hold Precautions • When the inside of the vehicle is very cold and the player is used soon after switching on the heater, condensation may form on the disc or the optical parts of the player and proper playback may not be possible. If condensation forms 99 5-14 76MH1-74E OTHER CONTROLS AND EQUIPMENT 76MH1-74E To remove the compact disc from its storage case, press down on the center of the case and lift the disc out, holding it carefully by the edges. Always handle the compact disc by the edges. Never touch the surface. Never stick labels on the surface of the compact disc or write on the surface with a pencil or pen. To remove fingermarks and dust, use a soft cloth, and wipe in a straight line from the center of the compact disc to the circumference. (B) (C) (B) New discs may have some roughness around the edges. The unit may not work or the sound may skip if such discs are used. Use a ball-point pen (B), etc. to remove the roughness (C) from the edges of the disc before inserting it into the unit. Do not use any solvents such as commercially available cleaners, anti-static spray, or thinner to clean compact discs. Do not expose compact discs to direct sunlight or any heat source. NOTE: • Do not use commercially available CD protection sheets or discs equipped with stabilizers, etc. These may get caught in the internal mechanism and damage the disc. • It may be impossible to play CD-R discs with this unit due to the recording conditions. • CD-RW discs cannot be played with this unit. WARNING Do not use compact discs that have large scratches, are misshaped, or cracked, etc. Use of such discs will cause damage or prevent the system from operating properly. This is a class I laser product. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Do not open covers and do not attempt to repair this unit by yourself. Refer servicing to qualified personnel. 100 5-15 76MH1-74E OTHER CONTROLS AND EQUIPMENT 76MH1-74E Basic Operations Adjusting bass/treble/balance /fader 1) Press the TUNE FOLDER PUSH SOUND knob (2). Each time the knob is pressed, sound adjustment will change as follows: The Bluetooth® word mark and logo are registered trademarks and are owned by the Bluetooth SIG, Ink. Stop using this unit and a Bluetooth® ready device whenever requested. This unit shares the communication frequency with other private or public wireless communication equipment such as a wireless LAN and other wireless communication radios. You should stop using this unit whenever you are notified that your unit disturbs other wireless communication immediately. Bluetooth® Mic (1) (if equipped) (1) (3) (2) Preset-EQ (EQ OFF) (1) Bass adjustment (BASS 0) Treble adjustment (TREBLE 0) (1) VOL PUSH POWER knob (2) TUNE FOLDER PUSH SOUND knob (3) MUTE button Turning power on/off Press the VOL PUSH POWER knob (1). The unit starts in the function mode it was in when the power was turned off last. Balance adjustment (BALANCE 0) Adjusting the volume Turn the VOL PUSH POWER knob (1). Turning it clockwise increases the volume; turning it counterclockwise decreases the volume. 2) Turn the TUNE FOLDER PUSH SOUND knob (2) to adjust the sound. NOTE: While driving, adjust the volume to an extent that sound and/or noise coming from outside the vehicle can be heard. Mute Press the MUTE button (3) to mute the sound. To cancel the mute, press the MUTE button (3) again. Fader adjustment (FADER 0) AVC adjustment (AVC LEVEL 2) Adjusting the AVC (Auto volume control) The Auto Volume Control (AVC) function automatically adjusts (increases/ decreases) the sound volume in accordance with vehicle speed. The AVC control is provided with three selectable levels (LEVEL OFF, 1, 2, 3). The range of volume adjustment increases together with the LEVEL number. 1) Press the TUNE FOLDER PUSH SOUND knob (2) until the AVC adjustment mode is selected. 101 5-16 76MH1-74E OTHER CONTROLS AND EQUIPMENT 2) Turn the TUNE FOLDER PUSH SOUND knob (2) to select the desired AVC adjustment level. (Initial setting: LEVEL 2) Preset-EQ Preset-EQ calls up various sound types in accordance with the listening music type. 1) Press the TUNE FOLDER PUSH SOUND knob (2) several times until “PRESET-EQ” appears. 2) Turn the TUNE FOLDER PUSH SOUND knob (2). Each time the knob is turned, preset EQ mode will change as follows: 76MH1-74E Listening to the Radio Selecting the FM band Press the FM button (1). Each time the button is pressed, the reception band will change as follows: (3) (4) (1) (2) (5) (7) (6) Display OFF (FLAT) JAZZ (B) ROCK CLASSIC HIP-HOP (1) (2) (3) (4) (5) (6) (7) FM button AM button Up button Down button TUNE FOLDER PUSH SOUND knob Preset buttons ([1] to [6]) AS button (A) Band (B) Frequency FM2 Selecting the AM band Press the AM button (2). Seek tuning Press the seek Up button (3) or the seek Down button (4). The unit stops searching for a station at a frequency where a broadcast station is available. (A) POP FM1 Manual tuning Turn the TUNE FOLDER PUSH SOUND knob (5). The frequency being received is displayed. Preset memory 1) Select the desired station. 2) Hold down a desired button ([1] to [6]) of the Preset buttons (6) to which you want to store the station for 2 seconds or longer. 102 5-17 76MH1-74E OTHER CONTROLS AND EQUIPMENT 76MH1-74E Auto store Hold down the AS button (7) for 2 seconds or longer. Six stations in good reception will automatically be stored to the Preset buttons (6) in order, starting from a station whose frequency is the lowest. NOTE: • Auto store can be released by pressing AS button (7) while auto store is under way. • When the auto store is performed, the station previously stored in the memory at the position is overwritten. • When there are fewer than 6 stations that can be stored even if 1 round of auto store operation is performed, no station will be stored at the remaining Preset buttons (6). • 6 stations can be preset for FM1 and FM2 in common, and 6 stations for AM in auto store mode. Auto store mode on/off Press the AS button (7). Each time the button is pressed, the mode is switched as follows: Radio Reception Radio reception can be affected by environment, atmospheric conditions, or radio signal’s power and distance from the station. Nearby mountains and buildings may interfere or deflect radio reception, causing poor reception. Poor reception or radio static can also be caused by electric current from overhead wires or high voltage power lines. Listening to a CD Insertion slot Eject button CD button Up button Down button RPT button RDM button DISP button (A) Track number (B) Play time NOTE: This product does not support 8 cm CD (sometimes called as “mini single CD”, “3inch CD”, “CD3”, etc.). (1) (2) (3) (4) (5) (6) (7) (A) (8) Display (A) AS mode on (1) (2) (3) (4) (5) (6) (7) (8) • CDs or CD-ROM carrying no mark (A) cannot be used. • Some discs recorded in CD-R/CD-RW format may sometimes be impossible to use. AS mode off (B) 103 5-18 76MH1-74E OTHER CONTROLS AND EQUIPMENT • A CD is to be inserted with its label side up. • When there is a CD already in the unit, it is impossible to insert another CD without ejecting the CD in the unit. Do not use force to insert a CD into the CD insertion slot. NOTICE • Never insert your finger or hand into the CD insertion slot. Never insert foreign objects. • Never insert a CD with glue coming out from adhesive tape or a rental CD label or with a trace indicating that adhesive tape or a rental CD label has been removed. This may cause the CD not to eject or result in a malfunction. Loading a CD Insert a CD in the Insertion slot (1). When a CD is loaded, play starts. Ejecting a CD Press the Eject button (2). When the ignition switch is in “LOCK” position, the CD remained ejected for around 15 seconds or longer will automatically be drawn inside the unit. (Auto reload function) The backup eject function: This function allows you to eject a CD by pressing the Eject button (2) even when the ignition switch is in “LOCK” position. 76MH1-74E NOTICE If you forcefully try to push an ejected CD inside the unit before auto reloading, the disc surface might be scratched. When reloading a CD, remove it from the unit completely before reloading. Listening to a CD When a CD is inserted, playback will automatically start. When a CD is already inside the unit, press the CD button (3) to start playback. Selecting a track • Press the Up button (4) to listen to the next track. • Press the Down button (5) twice to listen to the previous track. When the Down button (5) is pressed once, the track currently being played will start from the beginning again. Fast forwarding/Rewinding a track • Hold down the Up button (4) to fast forward the track. • Hold down the Down button (5) to fast rewind the track. Random playback Press the RDM button (7). Each time the button is pressed, the mode will change as follows: OFF TRACK RANDOM • TRACK RANDOM The random indicator “RDM” will light. The tracks in the loaded disc will be played in random order. Repeat playback Press the RPT button (6). Each time the button is pressed, the mode will change as follows: OFF TRACK REPEAT • TRACK REPEAT The repeat indicator “RPT” will light. The track currently being played will be played repeatedly. 104 5-19 76MH1-74E OTHER CONTROLS AND EQUIPMENT 76MH1-74E Display change Press the DISP button (8). Each time the button is pressed, display will change as follows: Play time Disc title Listening to an MP3/WMA/AAC Disc (2) (3) (4) (1) (6) (5) Track title NOTE: • “NO TITLE” will be displayed when there is no text information in the disc currently being played. • If text data contains more than 12 characters, the “>” mark will appear at the right end. Holding down the DISP button (8) for 1 second or longer can display the next page. Display (A) (D) (B) (C) (1) (2) (3) (4) (5) (6) TUNE FOLDER PUSH SOUND knob Up button Down button RPT button RDM button DISP button (A) (B) (C) (D) Folder number Track number Play time DISC type Selecting a folder Turn the TUNE FOLDER PUSH SOUND knob (1) to select a folder. Selecting a track • Press the Up button (2) to listen to the next track. • Press the Down button (3) twice to listen to the previous track. When the Down button (3) is pressed once, the track currently being played will start from the beginning again. Fast forwarding/Rewinding a track • Hold down the Up button (2) to fast forward the track. • Hold down the Down button (3) to fast rewind the track. Random playback Press the RDM button (5). Each time the button is pressed, the mode will change as follows: OFF FOLDER RANDOM ALL RANDOM • FOLDER RANDOM The random indicator “RDM.F” will light. The tracks in the current folder will be played in random order. • ALL RANDOM The random indicator “RDM” will light. 105 5-20 76MH1-74E OTHER CONTROLS AND EQUIPMENT The tracks in the loaded disc will be played in random order. Repeat playback Press the RPT button (4). Each time the button is pressed, the mode will change as follows: 76MH1-74E Display change Press the DISP button (6). Each time the button is pressed, display will change as follows: Play time OFF FILE REPEAT FOLDER REPEAT Folder name File name Album name (MP3, AAC only) • FILE REPEAT The repeat indicator “RPT” will light. The track currently being played will be played repeatedly. • FOLDER REPEAT The repeat indicator “RPT.F” will light. All tracks in the currently selected folder will be played repeatedly. Track title Artist name NOTE: • “NO TITLE” will be displayed when there is no text information in the disc currently being played. • If text data contains more than 12 characters, the “>” mark will appear at the right end. Holding down the DISP button (6) for 1 second or longer can display the next page. Notes on MP3/WMA/AAC What is MP3? • MP3 (MPEG audio layer3) is an audio compression format that has become the standard format among PC users. Its merit is that the original audio data is compressed to approximately 1/10 and high sound quality is maintained. This means that it is possible to store the data of approximately 10 music CDs on a single CD-R/RW disc, which in turn makes it possible to play music for a long time without having to change the disc. What is WMA? • An abbreviation of “Windows Media Audio,” WMA is an audio compression format developed by Microsoft. • WMA files for which the DRM (Digital Rights Management) function is ON cannot be played. • Windows MediaTM and the Windows® logo are trademarks or registered trademarks of Microsoft Corporation in the United States and other countries. What is AAC? • An abbreviation of “Advanced Audio Coding,” AAC is an audio compression format used by MPEG2 and MPEG4. 106 5-21 76MH1-74E OTHER CONTROLS AND EQUIPMENT 76MH1-74E Points to remember when making MP3/ WMA/AAC files Common • High bit rate and high sampling frequency are recommended for high quality sounds. • Selecting VBR (Variable Bit Rate) is not recommended. Selecting VBR may cause display of incorrect playing time and jumpiness of playback. • Playback sound quality varies depending on the encoding environment. For details, refer to the user manual of the encoding software and the writing software in use. NOTICE Never assign the “.mp3”, “.wma”, or “.m4a” file name extension to a file if it is not in the MP3/WMA/AAC format file. Failure to observe this may result in damage to the speaker due to noise production. Recording MP3/WMA/AAC files on a CD media • It is recommended not to write both CDDA files and MP3/WMA/AAC files on a disc. • If both CD-DA files and MP3/WMA/AAC files are on the same disc, tracks may not be played in the correct order or some tracks may not be played at all. • When storing both MP3 data and WMA data on the same disc, sort and place them in different folders. • Do not write files other than MP3/WMA/ AAC files and unnecessary folders on a disc. • MP3/WMA/AAC files should be named to meet the standards and the file system specifications as shown below. • The file extension “.mp3”, “.wma” or “.m4a” should be assigned to files based on their format independently. • You may encounter a trouble in playing MP3/WMA/AAC files or displaying information of MP3/WMA/AAC files depending on the writing software or CD recorder in use. • This unit does not have a play list function. • It is recommended to write discs in Discat-Once mode even though Multi-session mode is supported. WMA (Ver. 7, Ver. 8, Ver. 9*) • Bit rate: CBR 32 k - 320 kbps • Sampling frequency: 32 k/44.1 k/48 kHz * WMA 9 Professional/LossLess/Voice are not supported. AAC* • Bit rate: ABR 16k - 320 kbbs • Sampling frequency: 32 k/44.1 k/48 kHz * Apple Lossless is not supported. Supported file systems ISO 9660 Level 1/Level 2, Joliet, Romeo Maximum number of files/folders • Maximum number of files: 512 • Maximum number of files in a folder: 255 • Maximum depth of tree structure: 8 • Maximum number of folders: 255 (Root folder is included.) Compression formats MP3 • Bit rate: MPEG1 Audio Layer III: 32 k - 320 kbps MPEG2 Audio Layer III: 8 k - 160 kbps MPEG2.5 Audio Layer III: 8 k - 160 kbps • Sampling frequency: MPEG1 Audio Layer III: 32 k/44.1 k/ 48 kHz MPEG2 Audio Layer III: 16 k/22.05 k/ 24 kHz MPEG2.5 Audio Layer III: 8 k/11.025 k/ 12 kHz 107 5-22 76MH1-74E OTHER CONTROLS AND EQUIPMENT Listening to files stored in a USB device (3) (4) (1) (5) (2) (7) (6) 76MH1-74E NOTICE Do not connect any USB device other than a USB memory or a USB audio player. Do not connect multiple USB devices to the USB connector using a USB hub, etc. Supplying power to multiple USB devices from the connector could cause overheating and smoking. Selecting a USB device mode Press the MEDIA button (1). Each time the button is pressed, the mode will change as follows: Fast forwarding/Rewinding a track • Hold down the Up button (3) to fast forward the track. • Hold down the Down button (4) to fast rewind the track. Random playback Press the RDM button (6). Each time the button is pressed, the mode will change as follows: OFF FOLDER RANDOM ALL RANDOM Display (A) (B) USB (iPod®) (if equipped) Bluetooth® audio (if equipped) (D) (C) (1) (2) (3) (4) (5) (6) (7) MEDIA button TUNE FOLDER PUSH SOUND knob Up button Down button RPT button RDM button DISP button (A) (B) (C) (D) Folder number Track number Play time File type AUX (if equipped) Selecting a folder Turn the TUNE FOLDER PUSH SOUND knob (2) to select the desired folder. Selecting a track • Press the Up button (3) to listen to the next track. • Press the Down button (4) twice to listen to the previous track. When the Down button (4) is pressed once, the track currently being played will start from the beginning again. • FOLDER RANDOM The random indicator “RDM.F” will light. The tracks in the currently selected folder will be played in random order. • ALL RANDOM The random indicator “RDM” will light. The tracks in the connected USB device will be played in random order. Repeat playback Press the RPT button (5). Each time the button is pressed, the mode will change as follows: 108 5-23 76MH1-74E OTHER CONTROLS AND EQUIPMENT 76MH1-74E OFF FILE REPEAT FOLDER REPEAT • FILE REPEAT The repeat indicator “RPT” will light. The track currently being played will be played repeatedly. • FOLDER REPEAT The repeat indicator “RPT.F” will light. All the tracks in the folder currently selected will be played repeatedly. Display change Press the DISP button (7). Each time the button is pressed, display will change as follows: Play time Folder name File name Album name (MP3, AAC only) Track title Artist name NOTE: • “NO TITLE” will be displayed when there is no text information in the disc currently being played. • If text data contains more than 12 characters, the “>” mark will appear at the right end. Holding down the DISP button (7) for 1 second or longer can display the next page. Notes on USB device Compatible USB devices • USB Mass Storage Class For details as to whether your USB memory/USB Audio is compatible with USB Mass Storage Class, please contact the USB memory/USB Audio manufacturer. • USB Standard Compatibility 1.1/2.0 Full Speed • File System FAT12/16/32, VFAT • Maximum current less than 1.0 A • If devices such as USB hub, extension cable are connected to the audio system, it may not be recognized. In such case connect the USB device directly to the audio system. • Devices such as MP3 player/Mobile phone/digital camera may not be recognized by the audio system for playing music. USB device connection • When connecting a USB device, make sure that the connector is pushed all the way into the port. • Do not leave the USB device for long periods of time in places inside the vehicle where the temperature can rise too high. • Back up any important data beforehand. We cannot accept responsibility for any lost data. • It is recommended not to connect a USB device that contains data files other than MP3/WMA/AAC format. Recording MP3/WMA/AAC files on a USB device • Playback or display may not be possible depending on the type of USB device in use or the condition of the recording. • Depending on the connected USB memory, the files may be played in different order from the order that the files were stored. Compression formats MP3 • Bit rate: MPEG1 Audio Layer III: 32 k - 320 kbps MPEG2 Audio Layer III: 8 k - 160 kbps MPEG2.5 Audio Layer III: 8 k - 160 kbps • Sampling frequency: MPEG1 Audio Layer III: 32 k/44.1 k/48 kHz MPEG2 Audio Layer III: 16 k/22.05 k/24 kHz MPEG2.5 Audio Layer III: 8 k/11.025 k/12 kHz WMA (Ver. 7, Ver. 8, Ver. 9*) • Bit rate: CBR 32 k -320 kbps • Sampling frequency: 32 k/44.1 k/48 kHz * WMA 9 Professional/LossLess/Voice are not supported. 109 5-24 76MH1-74E OTHER CONTROLS AND EQUIPMENT AAC* • Bit rate: ABR 16k - 320 kbbs • Sampling frequency: 32 k/44.1 k/48 kHz * Apple Lossless is not supported. Maximum number of files/folders • Maximum number of files: 2500 • Maximum number of files in a folder: 255 • Maximum depth of tree structure: 8 • Maximum number of folders: 255 (Root folder is included.) Listening to an iPod® 76MH1-74E (1) (2) (3) (4) (5) (6) (7) (8) MEDIA button TUNE FOLDER PUSH SOUND knob Up button Down button RPT button RDM button DISP button Preset buttons ([1] to [6]) (A) Track title (B) Track number (C) Play time Selecting an iPod® mode Press the MEDIA button (1). Each time the button is pressed, the mode will change as follows: (3) (4) USB (iPod®) (if equipped) (1) (5) (7) (2) (6) Bluetooth® audio (if equipped) AUX (if equipped) (8) Display (A) (B) (C) Selecting a track • Press the Up button (3) to listen to the next track. • Press the Down button (4) twice to listen to the previous track. When the Down button (4) is pressed once, the track currently being played will start from the beginning again. Fast forwarding/Rewinding a track • Hold down the Up button (3) to fast forward the track. • Hold down the Down button (4) to fast rewind the track. Random playback Press the RDM button (6). Each time the button is pressed, the mode will change as follows: OFF SONG RANDOM ALBUM RANDOM • SONG RANDOM The random indicator “RDM” will light. The tracks in the iPod® will be played in random order. • ALBUM RANDOM The random indicator “D.RDM” will light. The albums in the iPod® will be played in random order. Repeat playback Press the RPT button (5). Each time the button is pressed, the mode will change as follows: OFF SONG REPEAT • SONG REPEAT The repeat indicator “RPT” will light. The track currently being played will be played repeatedly. 110 5-25 76MH1-74E OTHER CONTROLS AND EQUIPMENT 76MH1-74E Display change Press the DISP button (7). Each time the button is pressed, display will change as follows: Playlist name / Track title (Playlist mode only) Artist name / Track title Album name / Track title Track title / Play time NOTE: If text data contains more than 12 characters, the “>” mark will appear at the right end. Holding down the DISP button (7) for 1 second or longer can display the next page. Playing Mode selection 1) Press the button numbered [6] of the Preset buttons (8) for 1 second or longer. 2) Turn the TUNE FOLDER PUSH SOUND knob (2). Each time the knob is turned, the mode will change as follows: PLAYLIST ARTIST ALBUM SONGS GENRE 3) Press the TUNE FOLDER PUSH SOUND knob (2) to select the desired mode. NOTE: • When the button numbered [6] of the Preset buttons (8) is pressed, the previous mode will be displayed. Notes on iPod® Supported iPod® • iPod® touch (5th generation) • iPod® touch (4rd generation) • iPod® touch (3rd generation) • iPod® touch (2nd generation) • iPod® touch (1st generation) • iPod® classic • iPod® nano (7th generation) • iPod® nano (6th generation) • iPod® nano (5th generation) • iPod® nano (4th generation) • iPod® nano (3rd generation) • iPod® nano (2nd generation) • iPod® nano (1st generation) • iPod® (5th generation) • iPhone® 5 • iPhone® 4S • iPhone® 4 • iPhone® 3GS • iPhone® 3G • iPhone® * Some functions may not be available depending on the model of iPod®. * iPod® is a trademark of Apple Inc., registered in the U.S. and other countries. * iPhone® is a trademark of Apple Inc., registered in the U.S. and other countries. * Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. 111 5-26 76MH1-74E OTHER CONTROLS AND EQUIPMENT iPod® connection • Make sure to detach the iPod® after pressing the engine switch to change the ignition switch is in “LOCK” position. The iPod® may not be shut down when it is being connected and may result in battery depletion. • Please do not connect iPod® accessories such as an iPod® remote control or headphones while connecting the iPod® with the unit. The unit may not operate correctly. AUX Function 76MH1-74E 2) Press the MEDIA button (1). Each time the button is pressed, the mode will change as follows: Bluetooth® Hands-Free (if equipped) USB (iPod®) (if equipped) Bluetooth® audio (if equipped) AUX (if equipped) (1) (2) (3) CAUTION (1) (1) MEDIA button AUX connection To listen to auxiliary audio sources (sold separately) through the unit, follow the instruction below. 1) Connect the auxiliary audio source to the AUX/USB socket (separately attached) with an AUX cable. • Before connection, mute the unit, and also keep the volume of the auxiliary audio source within a range that will not cause distortion. • When the audio source is turned off, noise may be emitted. Be sure to turn off the unit or switch to another mode before turning off the audio source. NOTE: • Please consult your place of purchase for details about whether a given auxiliary audio source can be connected and the proper auxiliary cord to use. • The volume and tone controls of the auxiliary audio source can be adjusted on the unit. • In AUX mode, the volume setting is different from another mode. (1) TUNE FOLDER PUSH SOUND knob (2) VOL PUSH POWER knob (3) Preset buttons Steering switch (4) (5) (6) 112 5-27 76MH1-74E 76MH1-74E (7) (4) (5) (6) (7) Bluetooth® setup button Off Hook button On Hook button VOL switch Phone registration To use the hands-free function with this unit, it is required to register the phone in advance. NOTE: • Up to 5 phones can be registered. • To set up a new phone, disconnect the audio player from the unit. Connect the audio player again after phone setup is completed if necessary. • When failed to establish the pairing within 120 seconds, the connecting operation will be canceled. Please try again or refer to the manual of the phone in use for how to establish the pairing with the phone. OTHER CONTROLS AND EQUIPMENT 1) Press the Bluetooth® setup button (4). The Bluetooth® setup menu will be displayed. 2) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Setup Bluetooth”, and press the knob (1) to determine the selection. 3) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Pairing”, and press the knob (1) to determine the selection. 4) Select “CAR AUDIO” from the Bluetooth® menu of the phone and establish the pairing. Refer to the manual of the phone in use for further information. 5) Enter the Passkey displayed on the unit to the phone. 6) Press the On Hook button (6). NOTE: • When selecting “Go Back”, the previous menu will be displayed. • When additionally registering a phone, operate the same step from 1). Receiving a call Press the Off Hook button (5) to receive a call. Ending a call Press the On Hook button (6) to end a call. Rejecting a call (only for supported models) Press the On Hook button (6) to reject a incoming call. Adjusting the listening volume • Turn the VOL PUSH POWER knob (2) during a call. Turning it clockwise increases the volume; turning it counterclockwise decreases the volume. • Press the VOL switch (7) during a call. Pressing “+” of the switch increases the volume, pressing “-” of the switch decreases the volume. Adjusting the ring volume • Turn the VOL PUSH POWER knob (2) while a call coming in. Turning it clockwise increases the volume; turning it counterclockwise decreases the volume. • Press the VOL switch (7) during a call. Pressing “+” of the switch increases the volume, pressing “-” of the switch decreases the volume. Adjusting the call or ringtone volume Follow the instructions below to adjust the call or ringtone volume. 1) Press the Bluetooth® setup button (4). The Bluetooth® setup menu will be displayed. 2) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Setup Telephone”, and press the knob (1) to determine the selection. 3) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Sound Setting”, and press the knob (1) to determine the selection. 113 5-28 76MH1-74E OTHER CONTROLS AND EQUIPMENT 4) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Call Volume” or “Ringtone Volume”, and press the knob (1) to determine the selection. The current call or ringtone volume will be displayed. 5) Turn the TUNE FOLDER PUSH SOUND knob (1) to select desired call or ringtone volume, and press the knob (1) to determine the selection. NOTE: When selecting “Go Back”, the previous menu will be displayed. Selecting the Ringtone Follow the instructions below to select a ringtone. 1) Press the Bluetooth® setup button (4). The Bluetooth® setup menu will be displayed. 2) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Setup Telephone”, and press the knob (1) to determine the selection. 3) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Sound Setting”, and press the knob (1) to determine the selection. 4) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Ringtone”, and press the knob (1) to determine the selection. The current ringtone will be sounded. 5) Turn the TUNE FOLDER PUSH SOUND knob (1) to select desired ring- 76MH1-74E tone, and press the knob (1) to determine the selection. NOTE: When selecting “Go Back”, the previous menu will be displayed. Dialing using Missed/Incoming/ Outgoing Calls Follow the instructions below to dial to the last dialed number again. NOTE: Up to 10 phone numbers of the latest calls can be stored. (10 each for dialed, received and missed call) 1) Press the Off Hook button (5). The Bluetooth® phonebook menu will be displayed. 2) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Missed Calls”, “Incoming Calls” or “Outgoing Calls”, and press the knob (1) to determine the selection. To dial from the dialed history or the received history, select “Missed Calls”, “Incoming Calls” or “Outgoing Calls” respectively. 3) Turn the TUNE FOLDER PUSH SOUND knob (1) to select the desired number, and press the knob (1) to determine the selection. 4) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Dial”, and press the knob (1) or the Off Hook button (5) to dial to the selected number. NOTE: • When selecting “Go Back”, the previous menu will be displayed. • Pressing “Confirm” after selecting “Add Speed Dial” can register the selected number in the speed dial. • Pressing “Confirm” after selecting “Delete” can delete the selected number from the call history. Deletion of call history Follow the instructions below to delete a missed/incoming/outgoing call history. 1) Press the Off Hook button (5). The Bluetooth® phonebook menu will be displayed. 2) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Setup Phonebook”, and press the knob (1) to determine the selection. 3) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Delete History”, and press the knob (1) to determine the selection. 4) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Missed Calls”, “Incoming Calls”, or “Outgoing Calls”, and press the knob (1) to determine the selection. 5) Turn the TUNE FOLDER PUSH SOUND knob (1) to select a number to be deleted or “ALL”, and press the knob (1) to determine the selection. 6) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Delete?” or “Delete All?”, and press the knob (1) to determine the selection. 114 5-29 76MH1-74E 76MH1-74E 7) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Confirm”, and press the knob (1) to complete the deletion. NOTE: When selecting “Go Back”, the previous menu will be displayed. Registration in Phonebook Registration of numbers in the phonebook. Follow the instructions below to register phone numbers in the Phonebook of the unit. 1) Press the Bluetooth® setup button (4). The Bluetooth® setup menu will be displayed. 2) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Setup Telephone”, and press the knob (1) to determine the selection. 3) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Setup Phonebook”, and press the knob (1) to determine the selection. 4) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Add Contacts”, and press the knob (1) to determine the selection. 5) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Overwrite All” or “Add One Contact”, and press the knob (1) to determine the selection. The “Rest of Memory XXXX: Ok?” will be displayed. 6) Press or turn the TUNE FOLDER PUSH SOUND knob (1) to select “Con- OTHER CONTROLS AND EQUIPMENT firm”, and press the knob (1) to determine the selection. 7) Transfer contacts from the phone. When the registration is completed, the “Setup Phonebook” will be displayed. NOTE: • When selecting “Go Back” the previous menu will be displayed. • Up to 1000 numbers can be registered in Phonebook. Transfer of call history (Call History) Follow the instructions below to transfer call history of the registered phone. 1) Press the Bluetooth® setup button (4). The Bluetooth® setup menu will be displayed. 2) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Setup Telephone”, and press the knob (1) to determine the selection. 3) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Call History”, and press the knob (1) to determine the selection. 4) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Call History?”, and press the knob (1) to determine the selection. 5) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Confirm”, and press the knob (1) to transfer the call history from the phone. NOTE: When selecting “Go Back”, the previous menu will be displayed. Making a call by Phonebook Follow the instructions below to dial a number registered in Phonebook. 1) Press the Off Hook button (5). The Bluetooth® phonebook menu will be displayed. 2) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Phonebook”, and press the knob (1) to determine the selection. 3) Turn the TUNE FOLDER PUSH SOUND knob (1) to select the initial of the name you would like to make a call, and press the knob (1) to determine the selection. The registered numbers will be displayed in sequence. If names have been registered together with numbers, the names will be displayed. 4) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Dial”, and press the knob (1) to determine the selection. 5) Press the Off Hook button (5). The displayed number or the number registered with the displayed name will be dialed. 115 5-30 76MH1-74E OTHER CONTROLS AND EQUIPMENT Deletion of registered data (Delete Entry) Follow the instructions below to delete a number registered in Phonebook. 1) Press the Bluetooth® setup button (4). The Bluetooth® setup menu will be displayed. 2) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Setup Telephone”, and press the knob (1) to determine the selection. 3) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Setup Phonebook”, and press the knob (1) to determine the selection. 4) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Delete Contacts”, and press the knob (1) to determine the selection. 5) Turn the TUNE FOLDER PUSH SOUND knob (1) to select a number to be deleted, and press the knob (1) to determine the selection. 6) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Delete?”, and press the knob (1) to determine the selection. 1) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Confirm”, and press the knob (1) to complete the deletion. NOTE: When selecting “Go Back”, the previous menu will be displayed. Registration in speed dial Follow the instructions below to assign a number to one of the Preset buttons to use as the speed dial. 1) Press the Bluetooth® setup button (4). The Bluetooth® setup menu will be displayed. 2) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Setup Telephone”, and press the knob (1) to determine the selection. 3) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Setup Phonebook”, and press the knob (1) to determine the selection. 4) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Add Speed Dial”, and press the knob (1) to determine the selection. 5) Turn the TUNE FOLDER PUSH SOUND knob (1) to select a number to be assigned, and press the knob (1) to determine the selection. 6) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Choose Preset”, and press the knob (1) to determine the selection. 7) Press one of the Preset buttons (3) to which the selected number is to be assigned. If a number is already assigned to the selected button, a confirmation message will be displayed. Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Confirm”, and press the knob (1) to complete the assignment. 76MH1-74E When the assignment is completed, the “Setup Phonebook” will be displayed. NOTE: When selecting “Go Back”, the previous menu will be displayed. One-touch call (Speed dial) Follow the instructions below to dial the number assigned to each of the Preset buttons (3). 1) Press the Off Hook button (5). The Bluetooth® phonebook menu will be displayed. 2) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Speed Dials”, and press the knob (1) to determine the selection. 3) Press one of the Preset buttons (3). When no number is assigned, “No Entry” is displayed. 4) Press the Off Hook button (5). The selected number will be dialed. 116 5-31 76MH1-74E 76MH1-74E Deletion of speed dial (Del Speed Dial) To delete a number assigned for the speed dial, follow the instructions below. 1) Press the Off Hook button (5). The Bluetooth® phonebook menu will be displayed. 2) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Speed Dials”, and press the knob (1) to determine the selection. 3) Press one of the Preset buttons (3) to which the number to be deleted is assigned. “No Entry” appears if the number is not registered. 4) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Delete”, and press the knob (1) to determine the selection. 5) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Del Speed Dial”, and press the knob (1) to determine the selection. 6) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Confirm”, and press the knob (1) to complete the deletion. OTHER CONTROLS AND EQUIPMENT Display of device data (Device Name) Follow the instructions below to display the BD (Bluetooth® Device) address and device name. 1) Press the Bluetooth® setup button (4). The Bluetooth® setup menu will be displayed. 2) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Setup Bluetooth”, and press the knob (1) to determine the selection. 3) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Bluetooth Info”, and press the knob (1) to determine the selection. 4) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Device Name” or “Device Address”, and press the knob (1) to display the device name or the BD (Bluetooth® Device) address. NOTE: When selecting “Go Back”, the previous menu will be displayed. Reset to the factory defaults Follow the instructions below to reset all the settings to the factory defaults. 1) Press the Bluetooth® setup button (4). The Bluetooth® setup menu will be displayed. 2) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Setup Bluetooth”, and press the knob (1) to determine the selection. 3) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Initialize”, and press the knob (1) to determine the selection. 4) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “All Initialize”, and press the knob (1) to determine the selection. 5) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Confirm”, and press the knob (1) to start the reset. NOTE: When selecting “Go Back”, the previous menu will be displayed. NOTE: When selecting “Go Back”, the previous menu will be displayed. 117 5-32 76MH1-74E OTHER CONTROLS AND EQUIPMENT Selection of phone (Select Phone) Follow the instructions below to select a phone to be paired with from the registered phones. 1) Press the Bluetooth® setup button (4). The Bluetooth® setup menu will be displayed. 2) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Setup Bluetooth”, and press the knob (1) to determine the selection. 3) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “List Phone”, and press the knob (1) to determine the selection. 4) Turn the TUNE FOLDER PUSH SOUND knob (1) to select a phone to be paired with, and press the knob (1) to determine the selection. 5) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Select”, and press the knob (1) to determine the selection. NOTE: • When selecting “Go Back”, the previous menu will be displayed. • The Bluetooth® ready audio device will be disconnected when the phone is selected. List of phones (List Phones) Follow the instructions below to display the names of the registered phones in sequence. 1) Press the Bluetooth® setup button (4). The Bluetooth® setup menu will be displayed. 2) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Setup Bluetooth”, and press the knob (1) to determine the selection. 3) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “List Phone”, and press the knob (1) to determine the selection. The names of the registered phones are displayed in sequence. NOTE: When selecting “Go Back”, the previous menu will be displayed. Passkey setting (Set Passkey) Follow the instructions below to set the security number (Passkey). 1) Press the Bluetooth® setup button (4). The Bluetooth® setup menu will be displayed. 2) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Setup Bluetooth”, and press the knob (1) to determine the selection. 3) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Passkey”, and press the knob (1) to determine the selection. 76MH1-74E 4) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “New Passkey”, and press the knob (1) to determine the selection. 5) Press or turn the TUNE FOLDER PUSH SOUND knob (1) to select “Confirm”. 6) Turn the TUNE FOLDER PUSH SOUND knob (1) to select a number for the first digit, and press the knob (1) to determine the selection. Select and determine numbers for the second, third and fourth digits in order in the same manner. When not entering up to the eighth digit, enter blanks for the successive digits. 7) Turn the TUNE FOLDER PUSH SOUND knob (1) to determine the passkey setting. NOTE: When selecting “Go Back”, the previous menu will be displayed. 118 5-33 76MH1-74E 76MH1-74E Deletion of phone information (Delete Phone) Follow the instructions below to delete the registered information of the phone. 1) Press the Bluetooth® setup button (4). The Bluetooth® setup menu will be displayed. 2) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Setup Bluetooth”, and press the knob (1) to determine the selection. 3) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “List Phone”, and press the knob (1) to determine the selection. 4) Turn the TUNE FOLDER PUSH SOUND knob (1) to select a phone to be deleted, and press the knob (1) to determine the selection. 5) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Delete Phone”, and press the knob (1) to determine the selection. 6) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Delete?”, and press the knob (1) to determine the selection. 7) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Confirm”, and press the knob (1) to determine the selection. OTHER CONTROLS AND EQUIPMENT BT function on/off (BT Power) Follow the instructions below to turn on/off the Bluetooth® function. 1) Press the Bluetooth® setup button (4). The Bluetooth® setup menu will be displayed. 2) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Setup Bluetooth”, and press the knob (1) to determine the selection. 3) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “BT Power”, and press the knob (1) to determine the selection. 4) Press the TUNE FOLDER PUSH SOUND knob (1) to select “BT Power On” or “BT Power Off”. NOTE: • When the BT function is turned off, the connection between this unit and the registered phone in use will be disconnected. • When selecting “Go Back”, the previous menu will be displayed. Bluetooth® audio (if equipped) (3) (4) (1) (5) (2) NOTE: • Applicable for Bluetooth® audio ver- sion 2.1 and above. Steering switch (6) NOTE: When selecting “Go Back”, the previous menu will be displayed. 119 5-34 76MH1-74E OTHER CONTROLS AND EQUIPMENT Display (A) (B) (1) (2) (3) (4) (5) (6) MEDIA button TUNE FOLDER PUSH SOUND knob Up button Down button DISP button Bluetooth® setup button (A) Track number (B) Play time Registration of audio devices To use Bluetooth® ready audio devices with this unit, it is required to register the devices. NOTE: • To set up a new audio player, disconnect the phone from the unit. Connect the phone after audio player setup is completed if necessary. • When failed to establish the connection within 120 seconds, the connecting operation will be canceled. Please try again or refer to the audio player manual for assistance with the pairing process. 1) Press the Bluetooth® setup button (6). The Bluetooth® setup menu will be displayed. 2) Turn the TUNE FOLDER PUSH SOUND knob (2) to select “Setup Bluetooth”, and press the knob (2) to determine the selection. 3) Turn the TUNE FOLDER PUSH SOUND knob (2) to select “Pairing”, and press the knob (2) to determine the selection. 4) Select “CAR AUDIO” from the Bluetooth® menu of the audio player and establish the pairing. Refer to the manual of the audio player in use for further information. 5) Enter the Passkey displayed on the unit to the audio player. (For phones with Bluetooth version 2.1 or above passkey input is not required). NOTE: • When selecting “Go Back”, the previous menu will be displayed. • When additionally registering audio devices, operate the same step from 1). Selecting the Bluetooth® audio mode Press the MEDIA button (1). Each time the button is pressed, the mode will change as follows: 76MH1-74E USB (iPod®) (if equipped) Bluetooth® audio (if equipped) AUX (if equipped) Selecting a group (only for supported models) Turn the TUNE FOLDER PUSH SOUND knob (2) to select a group. Selecting a track Press the Up button (3) to listen to the next track. Press the Down button (4) twice to listen to the previous track. When the Down button (4) is pressed once, the track currently being played will start from the beginning again. Fast forwarding/Rewinding a track • Hold down the Up button (3) to fast forward the track. • Hold down the Down button (4) to fast rewind the track. NOTE: Some functions may not be available depending on Bluetooth® audio. Display change Press the DISP button (5). Each time the button is pressed, display will change as follows: 120 5-35 76MH1-74E 76MH1-74E Play time Track name Artist name Album name NOTE: If text data contains more than 12 characters, the “>” mark will appear at the right end. Holding down the DISP button (5) for 1 second or longer can display the next page. Selection of audio device (Select Audio) Follow the instructions below to select an audio device to be paired with from the registered audio devices. 1) Press the Bluetooth® setup button (6). The Bluetooth® setup menu will be displayed. 2) Turn the TUNE FOLDER PUSH SOUND knob (2) to select “Setup Bluetooth”, and press the knob (2) to determine the selection. 3) Turn the TUNE FOLDER PUSH SOUND knob (2) to select “List Audio”, and press the knob (2) to determine the selection. 4) Turn the TUNE FOLDER PUSH SOUND knob (2) to select an audio OTHER CONTROLS AND EQUIPMENT device to be used, and press the knob (2) to determine the selection. 5) Turn the TUNE FOLDER PUSH SOUND knob (2) to select “Select”, and press the knob (2) to determine the selection. 6) Turn the TUNE FOLDER PUSH SOUND knob (2) to select “Confirm”, and press the knob (2) to complete the pairing. NOTE: • When selecting “Go Back”, the previous menu will be displayed. • The phone will be disconnected when the Bluetooth® ready audio device is selected. List of audio devices (List Audio) Follow the instructions below to display the names of the registered audio devices in sequence. 1) Press the Bluetooth® setup button (6). The Bluetooth® setup menu will be displayed. 2) Turn the TUNE FOLDER PUSH SOUND knob (2) to select “Setup Bluetooth”, and press the knob (2) to determine the selection. 3) Turn the TUNE FOLDER PUSH SOUND knob (2) to select “List Audio”, and press the knob (2) to determine the selection. The names of registered audio devices will be displayed in sequence. NOTE: When selecting “Go Back”, the previous menu will be displayed. Passkey setting (Set Passkey) Follow the instructions below to set the security number (Passkey). 1) Press the Bluetooth® setup button (6). The Bluetooth® setup menu will be displayed. 2) Turn the TUNE FOLDER PUSH SOUND knob (2) to select “Setup Bluetooth”, and press the knob (2) to determine the selection. 3) Turn the TUNE FOLDER PUSH SOUND knob (2) to select “Passkey”, and press the knob (2) to determine the selection. 4) Turn the TUNE FOLDER PUSH SOUND knob (2) to select “New Passkey”, and press the knob (2) to determine the selection. 5) Press or turn the TUNE FOLDER PUSH SOUND knob (2) to select “Confirm”. 6) Turn the TUNE FOLDER PUSH SOUND knob (2) to select a number for the first digit, and press the knob (2) to determine the selection. Select and determine numbers for the second, third and fourth digits in order in the same manner. When not entering up to the eighth digit, enter blanks for the successive digits. 7) Turn the TUNE FOLDER PUSH SOUND knob (2) to determine the passkey setting. 121 5-36 76MH1-74E OTHER CONTROLS AND EQUIPMENT 76MH1-74E NOTE: When selecting “Go Back”, the previous menu will be displayed. NOTE: When selecting “Go Back”, the previous menu will be displayed. Deletion of audio device information (Delete Audio) Follow the instructions below to delete the registered information of audio device. 1) Press the Bluetooth® setup button (6). The Bluetooth® setup menu will be displayed. 2) Turn the TUNE FOLDER PUSH SOUND knob (2) to select “Setup Bluetooth”, and press the knob (2) to determine the selection. 3) Turn the TUNE FOLDER PUSH SOUND knob (2) to select “List Audio”, and press the knob (2) to determine the selection. 4) Turn the TUNE FOLDER PUSH SOUND knob (2) to select an audio device to be deleted, and press the knob (2) to determine the selection. 5) Turn the TUNE FOLDER PUSH SOUND knob (2) to select “Delete”, and press the knob (2) to determine the selection. 6) Turn the TUNE FOLDER PUSH SOUND knob (2) to select “Delete?”, and press the knob (2) to determine the selection. 7) Turn the TUNE FOLDER PUSH SOUND knob (2) to select “Confirm”, and press the knob (2) to complete the deletion. Disclaimer for Bluetooth® function • Depending on the mobile phone models, some phones may not be compatible fully or partially (some function may be restricted). • Connectivity or voice quality may get affected depending on circumstances. • After the ignition switch is turned to the “ON” position, the audio system takes few seconds to detect and connect to the Bluetooth® device (if already paired). • Make sure that you are aware of all applicable local laws and accordingly use Bluetooth device. Adjusting the volume • To increase the volume, hold down “+” of the VOL switch (1). The volume will keep on being increased until the switch is released. • To decrease the volume, hold down “-” of the VOL switch (1). The volume will keep on being decreased until the switch is released. • To mute the sound, press the switch (2). Selecting the mode Press the switch (3). Each time the button is pressed, the mode will change as follows: FM1 (Radio) Remote Audio Controls (if equipped) FM2 (Radio) Controlling of basic functions of the audio system is available using the switches on the steering wheel. CD Bluetooth® audio (if equipped) AUX (if equipped) (2) (3) USB (iPod®) (if equipped) AM (Radio) It is possible to turn on the audio system by pressing the switch (3). (1) (4) 122 5-37 76MH1-74E OTHER CONTROLS AND EQUIPMENT 76MH1-74E Anti-Theft Feature < < Selecting the radio station (FM1, FM2, AM mode) • To select the next preset station, press “ ” of the switch (4) only for a moment. • To select the previous preset station, press “ ” of the switch (4) only for a moment. • To scan a higher frequency radio station, press “ ” of the switch (4) for 1 second or longer. • To scan a lower frequency radio station, press “ ” of the switch (4) for 1 second or longer. (3) < (4) (1) < (2) < < Selecting the track (CD, USB (iPod®), Bluetooth® audio mode) • To skip to the next track, press “ ” of the switch (4) only for a moment. • To skip to the previous track, press “ ” of the switch (4) twice only for a moment. When the switch (4) is pushed down once only for a moment, the track currently being played will start from the beginning again. < < Fast forwarding/Rewinding a track • To fast forward, press “ ” of the switch (4) for 1 second or longer. • To fast rewind, press “ ” of the switch (4) for 1 second or longer. (1) (2) (3) (4) VOL PUSH POWER knob Preset buttons ([1] to [6]) Up button TUNE FOLDER PUSH SOUND knob The anti-theft function is intended to discourage thefts, such as that the audio system becomes inoperable when it is installed on other vehicles. This function works by entering a Personal Identification Number (PIN). When the unit is disconnected from its power source, such as when the audio system is removed or the battery is disconnected, the unit will become inoperable until the PIN is reentered. Setting the Anti-Theft Function 1) Press the VOL PUSH POWER knob (1) to power off. 2) Hold down the buttons numbered [1] and [6] of the Preset buttons (2) and press the VOL PUSH POWER knob (1) “SECURITY” will be displayed. 3) Press the Up button (3) and the button numbered [1] of the Preset buttons (2) simultaneously. 4) Enter a 4-digit number to be registered as PIN using the buttons numbered [1] [4] of the Preset buttons (2). 5) Hold down the TUNE FOLDER PUSH SOUND knob (4) for 1 second or longer to set the anti-theft function. NOTE: Take a note of the registered PIN and keep it for the future use. Canceling the anti-theft feature To cancel the anti-theft function, delete the registered PIN. 1) Press the VOL PUSH POWER knob (1) to power off. 2) Hold down the buttons numbered [1] and [6] of the Preset buttons (2) and press the VOL PUSH POWER knob (1). “PIN ENTRY” will be displayed. 3) Press the Up button (3) and the button numbered [1] of the Preset buttons (2) simultaneously. 4) Enter a 4-digit number to be registered as PIN using the buttons numbered [1] [4] of the Preset buttons (2). 5) Hold down the TUNE FOLDER PUSH SOUND knob (4) for 1 second or longer to delete the registered PIN. The indication “----” will be displayed and the anti-theft function will be canceled. 123 5-38 76MH1-74E OTHER CONTROLS AND EQUIPMENT NOTE: To change your PIN, first delete your current PIN, then set a new one. Confirming the Personal Identification Number (PIN) When the main power source is disconnected such as when the battery is replaced, etc, it is required to enter the PIN to make the unit operable again. 1) Set the ignition switch to the “ACC” position. “SECURITY” will be displayed. 2) Press the Up button (3) and the button numbered [1] of the Preset buttons (2) simultaneously. 3) Enter a 4-digit number to be registered as PIN using the buttons numbered [1] [4] of the Preset buttons (2). 4) Hold down TUNE FOLDER PUSH SOUND knob (4) for 1 second or longer. When the PIN same as registered is entered, the power of the audio system will be turned off automatically and it will become operable again. NOTE: If an incorrect PIN is entered, “ERROR” and the total number of incorrect entry attempts will be displayed. If an incorrect PIN is entered 10 times, “HELP” will be displayed and the audio system will become inoperable. 76MH1-74E Battery Installation Install a lithium battery (CR2025) with the poles facing the correct direction. Battery replacement timing • When battery power is depleted, the button may not be operable. If the remote controller does not operate, replace the battery and check the operation. Caution on battery • Be sure to follow the instructions to prevent battery leakage, over-heating, ignition or explosion. WARNING • Do not expose the battery to flame. Do not short circuit, disassemble, or heat the battery. • Do not charge the battery. • Use the specified type battery. • Keep the button-shaped battery away from children to prevent accidental swallowing. If the battery is swallowed, contact a doctor immediately. CAUTION • Install the battery with the poles facing the correct direction. • When not in use for a long period of time, or if the battery is dead, remove the battery from the remote controller. If battery leakage has occurred, wipe the container first then install a new battery. If the battery solution contacts the skin, wash off with water completely. Caution on Remote Controller • Do not leave the remote controller in an area exposed to direct sunlight, such as on the dashboard or steering wheel. The remote controller may deform because of the heat, (Be especially careful of the dashboard exposed to direct sunlight in the summer, as it will become extremely hot). • When the vehicle is parked in an area exposed to direct sunlight, Ensure the remote controller is placed in an area not exposed to direct sunlight. For example: Glove box. Under direct sunlight, signal reception from the remote controller weakens. If this happens, hold the remote controller close to the signal receptor on the front panel. 124 5-39 76MH1-74E OTHER CONTROLS AND EQUIPMENT 76MH1-74E Remote Controller Common operations POWER button • Power ON / OFF VOLUME button • Press to adjust volume. (including at AUX mode) TUNE FOLDER UP/DOWN button • In Sound Mode Press to adjust the sound.(bass/treble/balance/ fader) • In Preset-EQ Mode The Preset-EQ setting switches as follows: OFF (FLAT) JAZZ ROCK POP SEEK TRACK MODE button • The mode switches as follows: CLASSIC FM1 HIP-HOP FM2 • In AVC Mode The AVC setting switches as follows: VOL - CD Bluetooth® audio (if equipped) TUNE/FLD ENT VOL + SEEK TRACK MUTE button • Press to mute the sound. Press it again to cancel the mute. TUNE/FLD 1 MENU 2 3 4 RPT 5 RDM 6 DISP MODE AS SOUND SOUND button • While playback, the sound mode switches as follows (including at AUX mode, except while displaying iPod menu): Preset-EQ BASS OFF AUX (if equipped) TREBLE LEVEL 1 USB (iPod®) (if equipped) BALANCE LEVEL 2 LEVEL 3 FADER AM AVC 125 5-40 76MH1-74E OTHER CONTROLS AND EQUIPMENT Radio operations AS button • Press to return to the last received frequency in the previous auto store mode. • Press it for 2 seconds or longer. It selects the stations with the stronger signals and stores them in order. VOL - SEEK TRACK TUNE/FLD ENT VOL + SEEK TRACK SEEK TRACK UP/DOWN button • Press to select the radio station. TUNE/FLD 1 MENU 2 3 4 RPT 5 RDM 6 DISP MODE AS SOUND PRESET buttons (1-6) • Press to select the desired preset station. NOTE: When there are fewer than 6 stations that can be stored even if 1 round of auto store operation is performed, no station will be stored at the remaining preset buttons. 126 5-41 76MH1-74E OTHER CONTROLS AND EQUIPMENT 76MH1-74E CD operations SEEK TRACK UP/DOWN button • Press to skip to the next/previous track. RDM (5) button • Press to play the current track randomly. Press it again to cancel. Press it for 1 second or longer to fast-forward/fastrewind the track. VOL - SEEK TRACK TUNE/FLD ENT VOL + SEEK TRACK TUNE/FLD RPT (4) button • Press to plays the current track repeatedly. Press it again to cancel. DISP (6) button • The display switches as follows: 1 MENU 2 3 Play time 4 RPT 5 RDM 6 DISP Disc title MODE AS SOUND Track title • Press it for 1 second or longer to display the next page. 127 5-42 76MH1-74E OTHER CONTROLS AND EQUIPMENT 76MH1-74E MP3/WMA/AAC Disc operations SEEK TRACK UP/DOWN button • Press to skip to the next/previous track. • Press it for 1 second or longer to fast-forward/ fast-rewind the track. TUNE FOLDER UP/DOWN button • Press to skip to the next/previous folder. DISP (6) button The display switches as follows: RPT (4) button The repeat mode switches as follows: OFF VOL - SEEK TRACK RDM (5) button The random mode switches as follows: OFF ENT VOL + SEEK TRACK Play time Folder name File name FILE REPEAT FOLDER REPEAT TUNE/FLD TUNE/FLD 1 MENU 2 3 4 RPT 5 RDM 6 DISP MODE AS Album name (MP3, AAC only) Track title SOUND Artist name • Press it for 1 second or longer to display the next page. FOLDER RANDOM ALL RANDOM 128 5-43 76MH1-74E OTHER CONTROLS AND EQUIPMENT 76MH1-74E USB operations SEEK TRACK UP/DOWN button • Press to skip to the next/previous file. • Press it for 1 second or longer to fast-forward/ fast-rewind the file. TUNE FOLDER UP/DOWN button • Press to skip to the next/previous folder. DISP (6) button The display switches as follows: RPT (4) button The repeat mode switches as follows: OFF VOL - SEEK TRACK ENT VOL + SEEK TRACK Play time Folder name File name FILE REPEAT FOLDER REPEAT TUNE/FLD TUNE/FLD 1 MENU 2 3 4 RPT 5 RDM 6 DISP MODE AS Album name (MP3, AAC only) Track title SOUND Artist name RDM (5) button The random mode switches as follows: • Press it for 1 second or longer to display the next page. OFF FOLDER RANDOM ALL RANDOM 129 5-44 76MH1-74E OTHER CONTROLS AND EQUIPMENT 76MH1-74E iPod operations SEEK TRACK UP/DOWN button • Press to skip to the next/previous file. • Press it for 1 second or longer to fast-forward/ fast-rewind the file. ENT button While displaying iPod menu, press to select the desired item and display the list. When a track is selected from the list, the playback starts. • The display switches as follows: DISP (6) button TUNE FOLDER UP/DOWN button While displaying iPod menu, press to display the next/previous list in the same layer. VOL - SEEK TRACK RPT (4) button Press to play the current track repeatedly. Press it again to cancel. TUNE/FLD ENT VOL + SEEK TRACK Playlist name / Track title (Playlist mode only) Artist name / Track title Album name / Track title TUNE/FLD 1 MENU 2 3 4 RPT 5 RDM 6 DISP MODE AS SOUND Track title / Play time • Press it for 1 second or longer to display the next page. RDM (5) button The random mode switches as follows: OFF SONG RANDOM ALBUM RANDOM MENU button During playback • Press to display iPod menu. • Press it for 1 second or longer to display the top menu. While iPod menu is displayed • Press to display the folder in one layer upper. • Press it for 1 second or longer to display the top menu. 130 5-45 76MH1-74E OTHER CONTROLS AND EQUIPMENT 76MH1-74E Troubleshooting When encountered a problem, check and follow the instructions as described below. If the described suggestions do not solve the problem, it is recommended to take the unit to your authorized MARUTI SUZUKI dealer. Problem Possible cause Possible solution Common Unable to operate The security function is on. When “SECURITY” is displayed, enter the ID. When “HELP” is displayed, contact your authorized MARUTI SUZUKI dealer. Unable to turn on the power (no sound). (No sound is produced) Fuse is blown. Contact your SUZUKI dealer. Much noise It may not be exactly tuned in to the station. Tune it in exactly to the station. Unable to receive by auto tuning There may be no station emitting signals powerful enough. Pick up a station by manual tuning. The disc is dirty. Wipe the disc with a soft cloth. The disc has a major scratch or is warped. Replace the disc with the one with no scratch and also not warped. authorized MARUTI Radio CD Sound skips or noise produced 131 5-46 76MH1-74E OTHER CONTROLS AND EQUIPMENT Problem 76MH1-74E Possible cause Possible solution MP3/WMA/AAC No playback The disc contains unsupported formatted data. Check the file format. Sound skips or noise produced Sound skipping may occur when playing VBR (Variable Bit Rate) files. It is not recommended to play VBR files. There is no supported format file to play on this unit. Check the file format. The current consumption of the USB device exceeds 1.0 A. Use an USB device with a current consumption lower than 1.0 A. The distance between this unit and the Bluetooth® ready device is too far, or a metallic object may be located between the Bluetooth® ready device and this unit. Change the location of the Bluetooth® ready device. The Bluetooth® function of the Bluetooth® ready device is off. Refer to the manual of the Bluetooth® ready device. (Some devices have the power saving function that automatically activates after a certain time.) Unable to receive a call. Your current location may be out of service area. Drive your vehicle to the service area of the phone. The voice quality of hands-free is low (Distortion, noise etc.). Another wireless device may be located near the unit. Switch off the wireless device or keep it away from the unit. USB Playback does not start when the USB device is connected. Bluetooth® Pairing failed 132 5-47 76MH1-74E OTHER CONTROLS AND EQUIPMENT 76MH1-74E Error Display Messages Display Possible cause Possible solution CD ERROR 1 The disc cannot be read. Insert the disc with its label side up. Check the disc if it is not warped or is free of flaws. When ERROR 1 does not disappear even when a normal disc is inserted, contact your dealer. ERROR 3 The player developed an error of an unidentified cause. When the CD is in the unit, press the CD eject button to remove the disc. When the disc cannot be ejected, contact your dealer. ERROR 1 The USB device is disconnected. Check the connection of the USB device. ERROR 2 Impossible to communicate correctly with the USB device. Unplug the USB device and plug it again. Check the USB device. ERROR 3 Inoperable due to an unidentified cause. Unplug the USB device and plug it again. When ERROR 3 does not disappear, contact your dealer. ERROR 4 The current consumption of the USB device exceeds 1.0 A. Check the USB device. USB/iPod® 133 5-48 76MH1-74E OTHER CONTROLS AND EQUIPMENT Display 76MH1-74E Possible cause Possible solution The player developed an error of an unidentified cause. Disconnect the Bluetooth® ready device and connect it again. When ERROR 1 does not disappear, contact your dealer. Failed to establish pairing Try to establish the pairing again. Reached the limit for the number of connected device information Delete information of unnecessary devices and try to establish the pairing again. Not Avail. Inoperable during driving Operate the system after pulling over your vehicle. Not Linked Phone is disconnected Try to establish the pairing again. Bluetooth® ERROR 1 Failed Memory Full 134 5-49 76MH1-74E 76MH1-74E VEHICLE LOADING AND TOWING VEHICLE LOADING AND TOWING Vehicle Loading ................................................................... 6-1 Trailer Towing ...................................................................... 6-1 Towing Your Vehicle ........................................................... 6-1 135 76MH1-74E VEHICLE LOADING AND TOWING Vehicle Loading Your vehicle was designed for specific weight capacities. The weight capacities of your vehicle are indicated by the Gross Vehicle Weight Rating (GVWR) and the Permissible maximum Axle Weight (PAW, front and rear). The GVWR and PAW (front and rear) are listed in the “SPECIFICATIONS” section. GVWR – Maximum permissible overall weight of the fully loaded vehicle (including all the occupants, accessories and cargo plus the trailer nose weight if towing a trailer). PAW – (Front and Rear) Maximum permissible weight on an individual axle. Actual weight of the loaded vehicle and actual loads at the front and rear axles can only be determined by weighing the vehicle. Compare these weights to the GVWR and PAW (front and rear). If the gross vehicle weight or the load on either axle exceeds these ratings, you must remove enough weight to bring the load down to the rated capacity. 76MH1-74E WARNING Never overload your vehicle. The gross vehicle weight (sum of the weights of the vehicle, all the occupants, accessories, cargo plus trailer nose weight if towing a trailer) must never exceed the Gross Vehicle Weight Rating (GVWR). In addition, never distribute a load so that the weight on either the front or rear axle exceeds the Permissible maximum Axle Weight (PAW). WARNING Always distribute cargo evenly. To avoid personal injury or damage to your vehicle, always secure cargo to prevent it from shifting if the vehicle moves suddenly. Place heavier objects on the floor and as far forward in the cargo area as possible. Never pile cargo higher than the top of the seat backs. Trailer Towing Your MARUTI SUZUKI was originally designed to carry people and a normal amount of cargo, not to tow a trailer.MARUTI SUZUKI does not recommend you use your vehicle to tow a trailer. Towing a trailer can adversely affect handling, durability, and fuel economy. Towing Your Vehicle Your vehicle may be towed behind another vehicle (such as a motorhome), provided your vehicle is 2 wheel drive (2WD) and you use the proper towing method specified for your vehicle. The towing method you must use depends on the specifications of your vehicle: whether it is a manual transaxle vehicle or an Auto Gear Shift vehicle. Use the towing instruction table to select the proper towing method for your vehicle, and carefully follow the corresponding instructions. Be sure to use proper towing equipment designed for recreational towing and make sure that towing speed does not exceed 90 km/h (55 mph). WARNING When you tow your vehicle, follow the instructions below to avoid accidents and damage to your vehicle. In addition, be sure to observe government and local requirements regarding vehicle lighting and trailer hitches or tow bars. WARNING A safety chain should always be used when you tow your vehicle. 136 6-1 76MH1-74E VEHICLE LOADING AND TOWING 76MH1-74E TOWING INSTRUCTION TABLE DRIVE TRAIN 2WD TRANSAXLE TOWING METHOD M/T AB Auto Gear Shift AB A: 2WD VEHICLES WITH MANUAL TRANSAXLE OR AUTO GEAR SHIFT 1) Secure the front wheels on a towing dolly according to the instructions provided by the dolly manufacturer. 2) Release the parking brake. TOWING METHOD B FROM THE FRONT: FOUR WHEELS ON THE GROUND TOWING METHOD A FROM THE FRONT: FRONT WHEELS ON A DOLLY AND REAR WHEELS ON THE GROUND 76MH023 B: 2WD VEHICLES WITH MANUAL TRANSAXLE OR AUTO GEAR SHIFT 1) Shift the gearshift lever into neutral. 2) Turn the ignition key to the “ACC” position to unlock the steering wheel. 3) Release the parking brake. 2WD M/T, Auto Gear Shift NOTICE After shifting the Auto Gear Shift lever to the “N” position, always check the gear position indicator in the instrument cluster shows the “N” position to make sure that the transaxle is disengaged. If the transaxle cannot be put in neutral, turn the key from the “LOCK” to the “ON” position, and move the Auto Gear Shift lever from “N” to “D”, “M” or “R”, then back to “N” again. Then turn the key from the “ON” to the “LOCK” position. These procedures may help put the transaxle in neutral. If the transaxle still cannot be put in neutral, you cannot tow the vehicle without using a towing dolly. NOTICE The steering column is not strong enough to withstand shocks transmitted from the front wheels during towing. Always unlock the steering wheel before towing. 76MH022 137 6-2 76MH1-74E 76MH1-74E INSPECTION AND MAINTENANCE INSPECTION AND MAINTENANCE Maintenance Schedule ....................................................... 7-2 Periodic Maintenance Schedule ........................................ 7-2 Drive Belt ............................................................................. 7-6 Engine Oil and Filter ........................................................... 7-6 Engine Coolant .................................................................... 7-10 Air Cleaner ........................................................................... 7-12 Spark Plugs ......................................................................... 7-12 Gear Oil ................................................................................ 7-14 Clutch Pedal ........................................................................ 7-14 Fuel Filter (Diesel engine) .................................................. 7-15 Brakes .................................................................................. 7-15 Steering ................................................................................ 7-17 Tires ...................................................................................... 7-18 Battery .................................................................................. 7-19 Fuses .................................................................................... 7-20 Bulb Replacement ............................................................... 7-23 Wiper Blades ....................................................................... 7-28 Windshield Washer Fluid ................................................... 7-31 Air Conditioning System .................................................... 7-31 138 76MH1-74E INSPECTION AND MAINTENANCE 76MH1-74E WARNING 60A187S WARNING You should take extreme care when working on your vehicle to prevent accidental injury. Here are a few precautions that you should be especially careful to observe: (Continued) (Continued) • To prevent damage or unintended activation of the air bag system be sure the battery is disconnected and the ignition switch has been in the “LOCK” position for at least 90 seconds before performing any electrical service work on your MARUTI SUZUKI. Do not touch air bag system components, or wires. The wires are wrapped with yellow tape or yellow tubing, and the couplers are yellow for easy identification. • Do not leave the engine running in garages or other confined areas. • When the engine is running, keep hands, clothing, tools, and other objects away from the fan and drive belt. Even though the fan may not be moving, it can automatically turn on without warning. • When it is necessary to do service work with the engine running, make sure that the parking brake is set fully and the transaxle is in Neutral. • Do not touch ignition wires or other ignition system parts when starting the engine or when the engine is running, or you could receive an electric shock. (Continued) WARNING (Continued) • Be careful not to touch a hot engine, exhaust manifold and pipes, muffler, radiator and water hoses. • Do not allow smoking, sparks, or flames around fuel or the battery. Flammable fumes are present. • Do not get under your vehicle if it is supported only with the portable jack provided in your vehicle. • Be careful not to cause accidental short circuits between the positive and negative battery terminals. • Keep used oil, coolant, and other fluids away from children and pets. Dispose of used fluids properly; never pour them on the ground, into sewers, etc. 139 7-1 76MH1-74E INSPECTION AND MAINTENANCE Maintenance Schedule The following table shows the times when you should perform regular maintenance on your vehicle. This table shows in miles, kilometers and months when you should perform inspections, adjustments, lubrication and other services. WARNING MARUTI SUZUKI recommends that maintenance on your Maruti Suzuki vehicle should be performed by MARUTI SUZUKI authorized workshop/ Service station. 76MH1-74E NOTICE Whenever it becomes necessary to replace parts on your vehicle, it is recommended that you use MARUTI genuine replacement parts or their equivalent. Periodic Maintenance Schedule “A” :Adjust “C”: Clean “R”: Replace or Change “I”: Inspect, clean, adjust, lubricate or replace as necessary “L”: Lubricate “T”: Tighten to Specified Torque “O”: Rotate NOTE: This table includes services as scheduled up to 80,000 km mileage. Beyond 80,000 km, carry out the same services at the same intervals respectively. 140 7-2 76MH1-74E INSPECTION AND MAINTENANCE 76MH1-74E FREE INSPECTION Interval: This interval should be judged by odometer reading km (x1000) or months, whichever comes first. months PERIODIC MAINTENANCE AT COST 1 5 10 20 30 40 50 60 70 80 1 6 12 24 36 48 60 72 84 96 R Engine 1-1. Water pump drive (Tension, Wear) - - - - - I - - - 1-2 Engine Coolant (Level, Leakage) l l l R l R l R l R 1-3 Engine oil and engine oil filter - - R R R R R R R R Petrol 1-4 Cooling system hoses and connections (Leakage and Damage) l l l l l l l l l l 1-5 Engine bolts (All cylinder head and manifold fixings) - - T - T _ T - T - 1-6 Engine Mounting (loose, damage) - - T - T - T - T - 1-7 Valve Clearance - - - - I - - I - - 1-8 Petrol Exhaust System (Noise, Leakage or otherwise defective) - l - l - I - I - l 1-9 Positive Crank Case Ventilation System (Hoses, Connections and Valve) - l - l - I - I - l 1-10 Exhaust Gas Recirculation Valve - - - - C - - C - - - - - l - l - l - l - - - - - R - - - R Clean after every 2,500 KM or as required. Replace after every 40,000 KM. More frequent replacement if dust condition is severe. l l - Diesel Ignition 2-1. Ignition wiring (Damage, Deterioration) 2-2. Spark Plug (Clean and adjust the gap) Petrol Fuel 3-1. Paved-road Clean after every 5,000 KM. Replace after every 40,000 KM. Air cleaner filter element 3-2. Dusty Condition Fuel tank cap, fuel lines and connections (Leakage and Damage) - l 3-3. Fuel Filter (Leakage) Petrol I I I I I I I I I R 3-4. Fuel Filter and Water Draining Diesel I I I R I R I R I R Clutch and Transmission 4-1. Clutch Pedal (Play) Petrol I I I I I I I I I I 4-2. Clutch fluid (level, leakage) Diesel l l l R l R l R l R 4-3. Clutch slipping (Dragging or Excess Damage) l l l l l l l l l l 141 7-3 76MH1-74E INSPECTION AND MAINTENANCE 76MH1-74E Interval: This interval should be judged by odometer reading or months, whichever comes first. km (x1000) months 4-4. FREE INSPECTION PERIODIC MAINTENANCE AT COST 1 5 10 20 30 40 50 60 70 80 1 6 12 24 36 48 60 72 84 96 Transmission Oil (Level, Leakage) Replace at 1,60,000 km or 10 years whichever comes first Drive shaft 5-1. Drive shaft boot (boot cut / damage) - l l l l l l l l l 5-2. Noise from drive shafts I I I I I I I I I I 6-1. Brake Fluid (Level, Leakage) I I I R I R I R I R 6-2. Brake pedal (pedal - carpet clearance) I I I I I I I I I I 6-3. Parking brake lever and cable (Play, damage) I I I I I I I I I I BRAKE 6-4. Brake disc and pad (Wear) – I I I I I I I I I 6-5. Brake drum and shoes (Wear) – – I I I I I I I I 6-6. Master cylinder and wheel cylinder or caliper, brake hoses and pipes (Fluid leakage, damage) I I I I I I I I I I 7-1. Tyres (air pressure, abnormal wear, crack and rotation) I I&O I&O I&O I&O I&O I&O I&O I&O I&O 7-2. Wheels (Damage) I I I I I I I I I I 7-3. Front/Rear wheel bearing (Loose, damage) – I I I I I I I I I I WHEEL FRONT / REAR SUSPENSION 8-1. Suspension strut (Oil leakage, damage) I I I I I I I I I 8-2. Suspension arms / Knuckle support (Loose, damage) – I I I I I I I I I 8-3. Rear spring (Damage) – I I I I I I I I I 8-4. Shock absorbers (Oil leakage, damage) I I I I I I I I I I 8-5. All bolts and nuts (Loose) – T T T T T T T T T 8-6. Suspension arms and torsion rods – I I I I I I I I I STEERING 9-1. Steering wheel (Play, loose) I I I I I I I I I I 9-2. All rods and arms (Loose, damage, wear) I I I I I I I I I I 142 7-4 76MH1-74E INSPECTION AND MAINTENANCE 76MH1-74E Interval: This interval should be judged by odometer reading or months, whichever comes first. km (x1000) months FREE INSPECTION PERIODIC MAINTENANCE AT COST 1 5 10 20 30 40 50 60 70 80 1 6 12 24 36 48 60 72 84 96 I ELECTRICAL 10-1. Battery electrolyte (Level, leakage) I I I I I I I I I 10-2. Wiring harness connection (Loose, damage) – I I I I I I I I I 10-3. Lightening system (Operation, stains, damage) I I I I I I I I I I 10-4. Horn (Operation) I I I I I I I I I I 10-5. System Voltage I I I I I I I I I I 11-1. All chassis bolts and nuts (Tighten) – I T T T T T T T T 11-2. All latches, hinges and locks (Function)) I I&L I&L I&L I&L I&L I&L I&L I&L I&L BODY ROAD TEST 12-1. Operation of Brakes, gear shifting and speedometer I I I I I I I I I I 12-2. Body and chassis noise I I I I I I I I I I AIR CONDITIONER (If equipped) 13-1. Check belt tension I I I I I I I I I I 13-2. Tighten compressor mounting bolt – T T T T T T T T T 13-3. All hose joint (Check, tighten) I I I I I I I I I I 13-4. Check functioning of Recirc flap I I I I I I I I I I 13-5. Clean condenser with low pressure water – C C C C C C C C C 13-6. Check belt for frayed edges – I I I I I I I I I 13-7. Check all mounting bolts – I I I I I I I I I 143 7-5 76MH1-74E INSPECTION AND MAINTENANCE Drive Belt 76MH1-74E Engine Oil and Filter (For Petrol Engine Model) Specified Oil WARNING When the engine is running, keep hands, hair, clothing, tools, etc. away from the moving fan and drive belts. Make sure the drive belt tension is correct. If the belt is too loose, insufficient battery charging, engine overheating, poor power steering, poor air conditioning, or excessive belt wear can result. When you press the belt with your thumb midway between the pulleys, there should be a deflection according to the following chart. (For Petrol Engine Model) DEF: 4.0 – 4.5 mm (0.16 – 0.18 in.) (1) 0W-20 o C -30 o F -22 -10 14 0 32 10 50 20 68 30 86 40 104 GE AC The belts should also be examined to ensure that they are not damaged. If you need to replace or adjust the belt have it done by your MARUTI SUZUKI dealer. -20 -4 68LM20702 DEF: 7 – 8 mm (0.28 – 0.31 in.) (1) Preferred Be sure that the engine oil you use comes under the quality classification of SL. Select the appropriate oil viscosity according to the above chart. : 100 N (10 kg, 22 lbs) press GE: Generator DEF: Deflection AC: Air conditioner compressor 51KM036 SAE 0W-20 (1) is the best choice for good fuel economy, and good starting in cold weather. (For Diesel Engine Model) The drive belts tension adjusted automatically. 144 7-6 76MH1-74E INSPECTION AND MAINTENANCE 76MH1-74E Oil Level Check (For Diesel Engine Model) Upper Lower EXAMPLE EXAMPLE (1) (1) 5W-30 -30 -22 -20 -4 -10 14 0 32 10 50 20 68 30 86 40 104 76MH024 (1) Preferred Be sure that the engine oil you use comes under the quality classification of ACEA A5/B5-10. Select the appropriate oil viscosity according to the above chart. (2) 76MH030 (1) Engine oil dipstick (Petrol engine) (2) Engine oil dipstick (Diesel engine) It is important to keep the engine oil at the correct level for proper lubrication of your vehicle’s engine. Check the oil level with the vehicle on a level surface. The oil level indication may be inaccurate if the vehicle is on a slope. The oil level should be checked either before starting the engine or at least 5 minutes after stopping the engine. The handle of the engine oil dipstick is colored yellow for easy identification. 52D084 Pull out the oil dipstick, wipe oil off with a clean cloth, insert the dipstick all the way into the engine, then remove it again. The oil on the stick should be between the upper and lower limits shown on the stick. If the oil level indication is near the lower limit, add enough oil to raise the level to the upper limit. NOTICE Failure to check the oil level regularly could lead to serious engine trouble due to insufficient oil. 145 7-7 76MH1-74E INSPECTION AND MAINTENANCE 76MH1-74E Changing Engine Oil and Filter NOTICE (For Diesel Engine Model) Do not top up the oil over the MAX limit. Too much oil causes serious engine trouble. Refilling Drain the engine oil while the engine is still warm. EXAMPLE EXAMPLE Open Close (1) EXAMPLE Open (2) Close (1) 68KH068 76MH037 (1) Engine oil filler cap (Petrol engine) (2) Engine oil filler cap (Diesel engine) 81A147 Remove the oil filler cap and pour oil slowly through the filler hole to bring the oil level to the upper limit on the dipstick. Be careful not to overfill. Too much oil is almost as bad as too little oil. After refilling, start the engine and allow it to idle for about a minute. Stop the engine, wait about 5 minutes and check the oil level again. 1) Remove the oil filler cap. 2) Place a drain pan under the drain plug. 3) Using a wrench, remove the drain plug and drain out the engine oil. CAUTION The engine oil temperature may be high enough to burn your fingers when the drain plug is loosened. Wait until the drain plug is cool enough to touch with your bare hands. Tightening torque for drain plug (1): Petrol engine: 35 Nm (3.6 kg-m, 25.8 lb-ft) Diesel engine: 35 Nm (3.6 kg-m, 25.8 lb-ft) WARNING New and used oil can be hazardous. Children and pets may be harmed by swallowing new or used oil. Keep new and used oil and used oil filters away from children and pets. Repeated, prolonged contact with used engine oil may cause skin cancer. Brief contact with used oil may irritate skin. (Continued) 146 7-8 76MH1-74E INSPECTION AND MAINTENANCE 76MH1-74E (For Petrol Engine Model) (For Diesel Engine Model) WARNING (Continued) To minimize your exposure to used oil, wear a long-sleeve shirt and moisture-proof gloves (such as dishwashing gloves) when changing oil. If oil contacts your skin, wash thoroughly with soap and water. Launder any clothing or rags if wet with oil. Recycle or properly dispose of used oil and filters. 4) Reinstall the drain plug and gasket. Tighten the plug with a wrench to the specified torque. Replace the Oil Filter (1) (2) 76MH031 54G092 (1) Loosen (2) Tighten (1) Loosen (2) Tighten Tightening (viewed from filter top) Tightening (viewed from filter top) 1) Using an oil filter wrench, turn the oil filter counterclockwise and remove it. 2) Using a clean rag, wipe off the mounting surface on the engine where the new filter will be seated. 3) Smear a little engine oil around the rubber gasket of the new oil filter. 4) Screw on the new filter by hand until the filter gasket contacts the mounting surface. (2) (1) 54G093 82JN146 (1) Oil filter (2) 1 turn (1) Oil filter (2) 3/4 turn 147 7-9 76MH1-74E INSPECTION AND MAINTENANCE NOTICE To tighten the oil filter properly, it is Important to accurately identify the position at which the filter gasket first contacts the mounting surface. 5) Tighten the filter specified turn from the point of contact with the mounting surface (or to the specified torque) using an oil filter wrench. Tightening torque for oil filter Petrol engine: 1 turn or 14 Nm (1.4 kg-m, 10.3 lb-ft) Diesel engine: 3/4 turn or 14 Nm (1.4 kg-m, 10.3 lb-ft) NOTICE To prevent oil leakage, make sure that the oil filter is tight, but do not over-tighten it. Refill with Oil and Check for Leaks 1) Pour oil through the filler hole and install the filler cap. For the approximate capacity of the oil, refer to the “CAPACITIES” item in the “SPECIFICATIONS” section. 2) Start the engine and look carefully for leaks at the oil filter and drain plug. Run the engine at various speeds for at least 5 minutes. 76MH1-74E 3) Stop the engine and wait about 5 minutes. Check the oil level again and add oil if necessary. Check for leaks again. MARUTI SUZUKI dealer can help you select the proper coolant. NOTICE NOTICE • When replacing the oil filter, it is recommended that you use a Maruti genuine replacement filter. If you use an after market filter, make sure it is of equivalent quality and follow the manufacturer’s instructions. • Oil leaks from around the oil filter or drain plug indicate incorrect installation or gasket damage. If you find any leaks or are not sure that the filter has been properly tightened, have the vehicle inspected by your MARUTI SUZUKI dealer. Engine Coolant Selection of Coolant To maintain optimum performance and durability of your engine, use MARUTI Genuine Coolant or equivalent. This type of coolant is best for your cooling system as it: • Helps maintain proper engine temperature. • Gives proper protection against freezing and boiling. • Gives proper protection against corrosion and rust. Failure to use the proper coolant can damage your cooling system. Your authorized To avoid damaging your cooling system: • Always use a high quality ethylene glycol base non-silicate type coolant diluted with distilled water at the correct mixture concentration. • Make sure that the proper mix is 50/ 50 coolant to distilled water (Diesel) and 30/70 (Petrol). Concentrations greater than this may cause overheating conditions. • Neither use 100% coolant nor 100% Plain water. • Do not add extra inhibitors or additives. They may not be compatible with your cooling system. • Do not mix different types of base coolants. Doing so may result in accelerated seal wear and/or the possibility of severe overheating and extensive engine damage. Coolant Level Check Check the coolant level at the reservoir tank, not at the radiator. With the engine cool, the coolant level should be between the “FULL” and “LOW” marks. 148 7-10 76MH1-74E INSPECTION AND MAINTENANCE 76MH1-74E Adding Coolant (For Petrol Engine Model) (For Diesel Engine Model) WARNING Engine coolant is harmful or fatal if swallowed or inhaled. Do not drink antifreeze or coolant solution. If swallowed, do not induce vomiting. Immediately contact a poison control center or a physician. Avoid inhaling mist or hot vapors; if inhaled, remove to fresh air. If coolant gets in eyes, flush eyes with water and seek medical attention. Wash thoroughly after handling. Solution can be poisonous to animals. Keep out of the reach of children and animals. FULL LOW 76MH0A107 76MH032 EXAMPLE NOTICE • The mixture you use should contain 30% concentration of antifreeze. • If the lowest ambient temperature in your area is expected to be – 35°C (–31°F) or below, use higher concentrations up to 60% following the instructions on the antifreeze container. WARNING It is hazardous to remove the reservoir tank cap (degassing tank cap) for a diesel engine when the water temperature is high, because scalding fluid and steam may be blown out under pressure. Wait until the coolant temperature has lowered before removing the cap. FULL LOW 76MH0A108 If the coolant level is below the “LOW” mark, more coolant should be added. Remove the reservoir tank cap and add coolant until the reservoir tank level reaches the “FULL” mark. Never fill the reservoir tank above the “FULL” mark. If the coolant level is below the “LOW” mark, more coolant should be added. When the engine is cool, remove the degassing tank cap by turning it anticlockwise slowly to release any pressure. And add coolant until the degassing tank level reaches the “FULL” mark. Never fill the degassing tank above the “FULL” mark. 149 7-11 76MH1-74E INSPECTION AND MAINTENANCE Coolant Replacement 76MH1-74E (For Diesel Engine Model) Since special procedures are required, we recommend you take your vehicle to your MARUTI SUZUKI dealer for coolant replacement. EXAMPLE EXAMPLE (1) Air Cleaner If the air cleaner is clogged with dust, there will be greater intake resistance, resulting in decreased power output and increased fuel consumption. (For Petrol Engine Model) EXAMPLE 76MH033 Unclamp the side clamps, and remove the element from the air cleaner case. If it appears to be dirty, replace it with a new one. Spark Plugs 68KH072 For nickel spark plugs (traditional type): You should inspect spark plugs periodically for carbon deposits. When carbon accumulates on a spark plug, a strong spark may not be produced. Remove carbon deposits with a wire or pin and adjust the spark plug gap. To access the spark plugs: 1) Unclamp and remove the bolt, then remove the air cleaner case. 2) If necessary, disconnect the coupler (1) while pushing the release lever. 3) Remove the bolts. 4) Pull the ignition coils out. EXAMPLE 76MH0A109 Unclamp the upper clamps, and remove the element from the air cleaner case. If it appears to be dirty, replace it with a new one. NOTE: When installation, make sure the wires, couplers, sealing rubber of top cover and washers, are correctly returned in place. 76MH0A109 150 7-12 76MH1-74E INSPECTION AND MAINTENANCE 76MH1-74E EXAMPLE Correct Loosen Wrong Tighten 78K179 60G160S NOTICE NOTICE • When pulling the ignition coils out, do not pull on the cable. Pulling on the cable can damage it. • When servicing the iridium/platinum spark plugs (slender center electrode type plugs), do not touch the center electrode, as it is easy to damage. • When installing the spark plugs, screw them in with your fingers to avoid stripping the threads. Tighten with a torque wrench to 17.5 Nm (1.8 kg-m, 12.9 lb-ft). Do not allow contaminants to enter the engine through the spark plug holes when the plugs are removed. • Never use spark plugs with the wrong thread size. 60B307 Spark plug gap “a” NGK KR6A-10: 0.95 – 1.05 mm (0.037 – 0.041 in.) NOTICE When replacing spark plugs, you should use the brand and type specified for your vehicle. For the specified plugs, refer to the “SPECIFICATIONS” section at the end of this book. If you wish to use a brand of spark plug other than the specified plugs, consult your MARUTI SUZUKI dealer. 151 7-13 76MH1-74E INSPECTION AND MAINTENANCE 76MH1-74E Gear Oil 68KH073 (1) Oil filler and level plug Manual Transaxle Oil/ Auto Gear Shift Oil When adding gear oil, use gear oil with the appropriate viscosity and grade as shown in the chart below. We highly recommend you use: “MARUTI SUZUKI GEAR OIL 75W-80” for manual transaxle gear oil or Auto Gear Shift oil. Manual transaxle oil (API GL-4) 75W-80 o C -30 F -22 o -20 -4 -10 14 0 32 10 50 20 68 30 86 40 104 68LM728 Gear Oil Level Check (1) To check the gear oil level, use the following procedure: 1) Park the vehicle on a level surface with the parking brake applied. Then, stop the engine. 2) Remove the oil filler plug (1). 3) Check the inside of the hole with your finger. If the oil level comes up to the bottom of the plug hole, the oil level is correct. If so, reinstall the plug. 4) If the oil level is low, add gear oil through the oil filler plug hole (1) until the oil level reaches the bottom of the filler hole, then reinstall the plug. Tightening torque (1): 21 Nm (2.1 kg-m, 15.5 lb-ft) NOTICE When tightening the plug, apply the following sealing compound or equivalent to the plug threads to prevent oil leakage. Manual transaxle sealant: MARUTI SUZUKI Bond No. “1216E” or “1217G” Gear Oil Change Since special procedures, materials and tools are required, it is recommended that you trust this job to your authorized MARUTI SUZUKI dealer. Clutch Pedal Cable control clutch (if equipped) EXAMPLE CAUTION After driving the vehicle, the transaxle oil temperature may be high enough to burn your skin. Wait until the oil filler plug is cool enough to touch with your bare hands before inspecting transaxle oil. 54G274 EXAMPLE Clutch pedal play “d”: 10 - 15 mm (0.4 - 0.6 in.) 152 7-14 76MH1-74E INSPECTION AND MAINTENANCE 76MH1-74E Measure the clutch pedal play by moving the clutch pedal with your hand and measuring the distance it moves until you feel slight resistance. The play in the clutch pedal should be between the specified values. If the play is more or less than the above, or clutch dragging is felt with the pedal fully depressed, have the clutch inspected by your MARUTI SUZUKI dealer. Fuel Filter (Diesel engine) Brakes Brake Fluid (For Petrol Engine Model) (1) Fluid Control Clutch (if equipped) 76MH035 The fuel filter works as a water sedimentor as well. 76MH034 Check the clutch pedal for smooth operation and clutch fluid level from time to time. If clutch dragging is felt with the pedal fully depressed, have the clutch inspected by your MARUTI SUZUKI dealer. If the clutch fluid level is near the “MIN” line, fill it up to the “MAX” line with Maruti genuine brake fluid. 76MH0A110 (For Diesel Engine Model) Drain water according to the Periodic Maintenance Schedule. To drain water: 1) Place a pan or ample rag under the fuel filter drain nozzle. 2) Loosen the drain screw (1). The water will be drained. 3) Tighten the drain screw when the water changes to the diesel fuel. 4) Tighten the drain knob. Tightening torque for drain screw 1.0 Nm (0.10 kg-m, 0.74 lb-ft) 76MH034 Check the brake fluid level by looking at the reservoir in the engine compartment. Check that the fluid level is between the 153 7-15 76MH1-74E INSPECTION AND MAINTENANCE “MAX” and “MIN” lines. If the brake fluid level is near the “MIN” line, fill it up to the “MAX” line with Maruti genuine brake fluid. WARNING Failure to follow the guidelines below can result in personal injury or serious damage to the brake system. • If the brake fluid in the reservoir drops below a certain level, the brake warning light on the instrument panel will come on (the engine must be running with the parking brake fully disengaged). Should the light come on, immediately ask your MARUTI SUZUKI dealer to inspect the brake system. • A rapid fluid loss indicates a leak in the brake system which should be inspected by your MARUTI SUZUKI dealer immediately. • Do not use any fluid other than Maruti genuine brake fluid. Do not use reclaimed fluid or fluid that has been stored in old or open containers. It is essential that foreign particles and other liquids are kept out of the brake fluid reservoir. CAUTION 76MH1-74E WARNING Brake fluid is harmful or fatal if swallowed, and harmful if it comes in contact with skin or eyes. If swallowed, do not induce vomiting. Immediately contact a poison control center or a physician. If brake fluid gets in eyes, flush eyes with water and seek medical attention. Wash thoroughly after handling. Solution can be poisonous to animals. Keep out of the reach of children and animals. NOTE: With disc brakes, the fluid level can be expected to gradually fall as the brake pads wear. Brake Pedal Check if the brake pedal stops at the regular height without “spongy” feeling when you depress it. If not, have the brake system inspected by your MARUTI SUZUKI dealer. If you doubt the brake pedal for the regular height, check it as follows: 54G108 Pedal to floor carpet minimum distance “a”: 66 mm (2.6 in.) With the engine running, measure the distance between the brake pedal and floor carpet when the pedal is depressed with approximately 30 kg (66 lbs) of force. The minimum distance required is as specified. Since your vehicle’s brake system is selfadjusting, there is no need for pedal adjustment. If the pedal to floor carpet distance as measured above is less than the minimum distance required, have your vehicle inspected by your MARUTI SUZUKI dealer. Brake fluid can harm your eyes and damage painted surfaces. Use caution when refilling the reservoir. 154 7-16 76MH1-74E INSPECTION AND MAINTENANCE 76MH1-74E NOTE: When measuring the distance between the brake pedal and floor wall, be sure not to include the floor mat or rubber on the floor wall in your measurement. Steering Parking Brake EXAMPLE EXAMPLE “c” 54G109 EXAMPLE 60G104S WARNING If you experience any of the following problems with your vehicle’s brake system, have the vehicle inspected immediately by your MARUTI SUZUKI dealer. • Poor braking performance • Uneven braking (brakes not working uniformly on all wheels.) • Excessive pedal travel • Brake dragging • Excessive noise • Pedal pulsation (pedal pulsates when depressed.) Ratchet tooth specification “b”: 4th – 9th Lever pull force (1): 200 N (20 kg, 45 lbs) Check the parking brake for proper adjustment by counting the number of clicks made by the ratchet teeth as you slowly pull up on the parking brake lever to the point of full engagement. The parking brake lever should stop between the specified ratchet teeth and the rear wheels should be securely locked. If the parking brake is not properly adjusted or the brakes drag after the lever has been fully released, have the parking brake inspected and/or adjusted by your MARUTI SUZUKI dealer. 68LM708 Steering wheel play “c”: 0 – 30 mm (0.0 – 1.2 in.) Check the play of the steering wheel by gently turning it from left to right and measuring the distance that it moves before you feel slight resistance. The play should be between the specified values. Check that the steering wheel turns easily and smoothly without rattling by turning it all the way to the right and to the left while driving very slowly in an open area. If the amount of free play is outside the specification or you find anything else to be wrong, an inspection must be performed by your MARUTI SUZUKI dealer. 155 7-17 76MH1-74E INSPECTION AND MAINTENANCE 76MH1-74E Tires (1) Tread wear indicator (2) Indicator location mark WARNING EXAMPLE 68KH075 The front and rear tire pressure specifications for your vehicle are listed on the Tire Information Label. Both the front and rear tires should have the specified tire pressure. Note that the value does not apply to the compact spare tire, if equipped. • Air pressures should be checked when the tires are cold or you may get inaccurate readings. • Check the inflation pressure from time to time while inflating the tire gradually, until the specified pressure is obtained. • Never under inflate or over inflate the tires. Under inflation can cause unusual handling characteristics or can cause the rim to slip on the tire bead, resulting in an accident or damage to the tire or rim. • Overinflation can cause the tire to burst, resulting in personal injury. Overinflation can also cause unusual handling characteristics which may result in an accident. EXAMPLE Tire Inspection Inspect your vehicle’s tires at least once a month by performing the following checks: 2) Check that the depth of the tread groove is more than 1.6 mm (0.06 in.). To help you check this, the tires have molded-in tread wear indicators in the grooves. When the indicators appear on the tread surface, the remaining depth of the tread is 1.6 mm (0.06 in.) or less and the tire should be replaced. 3) Check for abnormal wear, cracks and damage. Any tires with cracks or other damage should be replaced. If any tires show abnormal wear, have them inspected by your MARUTI SUZUKI dealer. CAUTION Hitting curbs and running over rocks can damage tires and affect wheel alignment. Be sure to have tires and wheel alignment checked periodically by your MARUTI SUZUKI dealer. 4) Check for loose wheel nuts. 5) Check that there are no nails, stones or other objects sticking into the tires. (1) 1) Measure the air pressure with a tire gauge. Adjust the pressure if necessary. Remember to check the spare tire, too. (2) 52KM110 156 7-18 76MH1-74E INSPECTION AND MAINTENANCE 76MH1-74E Battery Tire Rotation WARNING • This is important to ensure proper steering and handling of the vehicle. Never mix tires of different size or type on the four wheels of your vehicle. The size and type of tires used should be only those approved by MARUTI SUZUKI as standard or optional equipment for your vehicle. • Replacing the wheels and tires equipped on your vehicle with certain combinations of aftermarket wheels and tires can significantly change the steering and handling characteristics of your vehicle. • Therefore, use only those wheel and tire combinations approved by MARUTI SUZUKI as standard or optional equipment for your vehicle. 5-tire rotation and 4-tire rotation WARNING 80JK040 To avoid uneven wear of your tires and to prolong their life, rotate the tires as illustrated. Tires should be rotated as mentioned in periodic maintenance schedule. After rotation, adjust front and rear tire pressures to the specification listed on your vehicle’s Tire Information Label. • Batteries produce flammable hydrogen gas. Keep flames and sparks away from the battery or an explosion may occur. Never smoke when working in the vicinity of the battery. • When checking or servicing the battery, disconnect the negative cable. Be careful not to cause a short circuit by allowing metal objects to contact the battery posts and the vehicle at the same time. • To avoid harm to yourself or damage to your vehicle or battery, follow the jump starting instructions in the “EMERGENCY SERVICE” section of this manual if it is necessary to jump start your vehicle. Wheel Balancing NOTICE Replacing the original tires with tires of a different size may result in false speedometer or odometer readings. If the vehicle vibrates abnormally on smooth road, have the wheel balanced at MARUTI SUZUKI Authorized Workshop Wheel Alignment In case of abnormal tire wear or pulling towards one side, have the wheel aligned at MARUTI SUZUKI Authorized Workshop. 157 7-19 76MH1-74E INSPECTION AND MAINTENANCE 76MH1-74E Fuses Replacement of the battery EXAMPLE - 1 EXAMPLE - 2 EXAMPLE (3) Your vehicle has three types of fuses, as described below: (1) Main fuse The main fuse takes current directly from the battery. (2) (4) 76MH0A136 For maintenance-free battery (cap-less type), you need not add water. For traditional type battery, which has water filler caps, the level of the battery solution must be kept between the “MAX” and the “MIN” level lines at all times. If the level is found to be below the “MIN” level line, add distilled water to the “MAX” level line. You should periodically check the battery, battery terminals, and battery hold-down bracket for corrosion. Remove corrosion using a stiff brush and ammonia mixed with water, or baking soda mixed with water. After removing corrosion, rinse with clean water. If your vehicle is not going to be driven for a month or longer, disconnect the cable from the negative terminal of the battery to help prevent discharge. CAUTION Do not overfill the battery with distilled water in order to avoid spillage. Primary fuses These fuses are between the main fuse and individual fuses, and are for electrical load groups. Individual fuses These fuses are for individual electrical circuits. 51KM039 To remove the battery: (1) Disconnect the negative cable (1). (2) Disconnect the positive cable (2). (3) Remove the retainer nuts (3) and remove the retainer (4) (4) Remove the battery. To install the battery: (1) Install the battery in the reverse order of removal. (2) Tighten the retainer nuts and battery cables securely. NOTE: When the battery is disconnected, some of the vehicle’s function will be initialized and/ or deactivated. These function are required to reset after the battery is reconnected. Fuses in the Engine Compartment (2) (3) (27) (1) (28) 68KH076 158 7-20 76MH1-74E INSPECTION AND MAINTENANCE 76MH1-74E (2) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13) (14) (15) (16) (17) (18) (19) (20) (21) (22) (23) (24) (25) (26) (3) (4) (5) (6) (7) (8) (9) (10) 68KH077 (11) (12) (13) (32) (33) (31) (14) (34) (29) (35) (30) (36) (15) (16) (17) 76MH036 MAIN FUSE/PRIMARY FUSE 80A FL1 (PETROL) (1) 120A FL1 (DIESEL) (18) (19) (20) (21) 50A 40A 50A – – – – – – 40A 40A 40A 40A 20A 7.5A 25A 30A 10A 15A 30A 10A 10A 15A 25A 15A FL5 (PETROL) FL5 (DIESEL) FL4 Front fog light relay Glow plug relay Blank Air compressor relay Back up relay F/P relay ABS motor T/M pump (PETROL) IGN2 (DIESEL) Power steering Front fog light T/M 2 (PETROL) F/P (DIESEL) Ignition switch Air compressor FI (PETROL) FI (DIESEL) T/M (PETROL) EPI (DIESEL) Headlight (Right) ABS control module Headlight (Left) (22) (23) (24) (25) (26) (27) (28) (29) (30) (31) (32) (33) (34) (35) (36) 30A 30A – – – – 80A 100A 80A 100A 20A 20A – – 15A 20A – – Starting motor Radiator fan FI main relay (PETROL) Glow plug 2 relay (DIESEL) Starting motor relay Radiator fan relay FL3 (PETROL) FL3 (DIESEL) FL2 (PETROL) FL2 (DIESEL) Glow plug Glow plug 2 FI main relay Blank FI2 INJ DRV Blank Blank The main fuse, primary fuses and some of the individual fuses are located in the engine compartment. If the main fuse blows, no electrical component will function. If a primary fuse blows, no electrical component in the corresponding load group will function. When replacing the main fuse, a primary fuse or an individual fuse, use a Maruti genuine replacement. 159 7-21 76MH1-74E INSPECTION AND MAINTENANCE To remove a fuse, use the fuse puller provided in the fuse box. The amperage of each fuse is shown in the back of the fuse box cover. 76MH1-74E Fuses under the Dash Board EXAMPLE EXAMPLE OK BLOWN 60G111 68KH078 WARNING If the main fuse or a primary fuse blows, be sure to have your vehicle inspected by an authorized MARUTI SUZUKI dealer. Always use a Maruti genuine replacement. Never use a substitute such as a wire even for a temporary repair, or extensive electrical damage and a fire can result. NOTE: Make sure that the fuse box always carries spare fuses. (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13) (14) (15) (16) (17) (18) (19) (20) (21) (23) (22) (24) 76MH0A111 160 7-22 76MH1-74E INSPECTION AND MAINTENANCE 76MH1-74E MAIN FUSE/PRIMARY FUSE (1) 10A Stop light (2) 30A Blower motor (3) 10A ST SIG (4) 15A Accessory (5) 10A Rear fog light (6) 10A Tail light (7) 10A Back-up light (8) 10A ABS (9) 10A Meter (10) 15A Ignition coil (11) 20A Wiper/Washer (12) 10A IG2 SIG (13) 10A IG1 SIG (14) 10A Air bag (15) 20A Power window timer (16) 20A Door lock (17) 15A Horn/Hazard (18) 20A Rear defogger (19) 15A Dome (20) 30A Power window (21) 7.5A ACC 2 (22) 15A Radio 2 (23) – Blank (24) – The fuse box is located under the driver’s side of the dashboard. Remove the fuse box cover by pushing in at both ends and pulling off the cover. Bulb Replacement CAUTION • Light bulbs can be hot enough to burn your finger right after being turned off. This is true especially for halogen headlight bulbs. Replace the bulbs after they become cool enough. • The headlight bulbs are filled with pressurized halogen gas. They can burst and injure you if they are hit or dropped. Handle them carefully. OK BLOWN NOTICE 81A283 WARNING Always be sure to replace a blown fuse with a fuse of the correct amperage. Never use a substitute such as aluminum foil or wire to replace a blown fuse. If you replace a fuse and the new one blows in a short period of time, you may have a major electrical problem. Have your vehicle inspected immediately by your MARUTI SUZUKI dealer. The oils from your skin may cause a halogen bulb to overheat and burst when the lights are on. Grasp a new bulb with a clean cloth. NOTICE Frequent replacement of a bulb indicates the need for an inspection of the electrical system. This should be carried out by your MARUTI SUZUKI dealer. Blank 161 7-23 76MH1-74E INSPECTION AND MAINTENANCE 76MH1-74E Headlights Side Turn Signal Light (if equipped) EXAMPLE Halogen headlights (1) (4) (5) 76MH0A114 (1) 76MH0A112 2) Push the retaining spring (4) forward and unhook it. Then remove the bulb (5). Install a new bulb in the reverse order of removal. (1) 76MH0A006 1) Remove the light housing (1) by sliding to left with your finger. (3) (2) (2) EXAMPLE 76MH0A113 76MH0A115 1) Open the engine hood. Disconnect the coupler (2). Remove the sealing rubber (3). NOTE: You can see the position of retaining spring from the hole of headlight. 76MH0A007 2) Turn the bulb holder (2) clockwise and pull it out from the light housing. 162 7-24 76MH1-74E INSPECTION AND MAINTENANCE 76MH1-74E (3) Removal (4) Install 2) To remove the bulb of the front turn signal light (1) from the bulb holder, push in the bulb and turn it counterclockwise. To install a new bulb, push it in and turn it clockwise. To remove and install the bulb of the front position light (2), simply pull out or push in the bulb. (2) (3) (4) (1) (5) Front Fog Light (if equipped) 76MH0A008 (4) Removal (5) Install 76MH0A117 3) To remove and install the bulb of the turn signal light (3), simply pull out or push in the bulb. Front Turn Signal Light (1) Front Position Light (2) 1) Open the engine hood. To remove the bulb holder of the front turn signal light (1) or the front position light (2) from the light housing, turn the holder counterclockwise and pull it out. 1) Start the engine. Turn the steering wheel to the opposite side of the replacing fog light to replace the bulb easily. Then turn off the engine. (1) EXAMPLE (2) (2) EXAMPLE (3) (4) 76MH0A119 (1) (1) 61MM0B078 2) Remove the clips (1) by prying it off with a flat blade screwdriver as shown in the illustration. 76MH0A116 163 7-25 76MH1-74E INSPECTION AND MAINTENANCE 76MH1-74E Rear Combination Light the reversing light (5) from the light housing, turn the holder counterclockwise and pull it out. EXAMPLE (2) (1) (3) / (4) / (5) EXAMPLE (6) 76MH0A120 3) Open the end of the cover inside the fender. 76MH0A121 (7) 1) Remove the bolts (1) and pull the light housing (2) straight. 76MH0A123 (6) Removal (7) Install EXAMPLE (3) 3) To remove the bulb of the tail/brake light (3), the turn signal light (4) or the reversing light (5) from bulb holder, push in the the bulb and turn it counterclockwise. To install a new bulb, push it in and turn it clockwise. (4) (5) 80JM071 4) Disconnect the coupler by pushing the lock release. Turn the bulb holder counterclockwise and remove it. 76MH0A122 2) To remove the bulb holder of the tail/ brake light (3), the turn signal light (4) or 164 7-26 76MH1-74E INSPECTION AND MAINTENANCE 76MH1-74E (2) (2) 76MH0A126 76MH0A124 NOTE: When reinstalling the light housing, make sure the clips are properly attached. 2) To remove and install the bulb of the license plate light (2), simply pull out or push in the bulb. High-mount Stop Light License Plate Light (1) (1) EXAMPLE 80J100 76MH0A125 1) Turn the cover (1) counterclockwise to remove it. 1) Open the tailgate, and remove the nuts (1) as shown in the illustration. EXAMPLE 76MH0A127 2) Close the tailgate. Remove the highmount stop light housing (2) from the tailgate. EXAMPLE 68KS063 3) Remove the bulb holder as shown in the illustration. 165 7-27 76MH1-74E INSPECTION AND MAINTENANCE 76MH1-74E Wiper Blades Type A EXAMPLE (3) (4) (5) 76MH0A128 (4) Removal (5) Install 60G115 54G129 Type B If the wiper blades become brittle or damaged, or make streaks when wiping, replace the wiper blades. 4) To remove and install the bulb of the high-mount stop light (3), simply pull out or push in the bulb. To install new wiper blades, follow the procedures below. Interior Light Remove the lens by using a flat blade screwdriver covered with a soft cloth as shown. To install it, simply push it back in. NOTICE To avoid scratching or breaking the window, do not let the wiper arm strike the window while replacing the wiper blade. 76MH0A139 166 7-28 76MH1-74E INSPECTION AND MAINTENANCE 76MH1-74E NOTE: Some wiper blades may be different from the ones described here depending on vehicle specifications. If so, consult your MARUTI SUZUKI dealer for proper replacement method. Removal EXAMPLE For windshield wipers: EXAMPLE 60A260 Installation 70G119 1) Hold the wiper arm away from the window. 54G130 2) Squeeze lock (1) towards wiper arm (2) and remove the wiper frame from the arm as shown. 3) Unlock the lock end of the wiper blade and slide the blade out as shown. 54G132 (1) Locked end 167 7-29 76MH1-74E INSPECTION AND MAINTENANCE 76MH1-74E For rear wipers: EXAMPLE (A) (B) (3) 54G135 (1) Retainer 4) If the new blade is provided without the two metal retainers, move them from the old blade to the new one. EXAMPLE (3) 60MH072 (A) Up (B) Down NOTE: When you install the metal retainers (3), make sure the direction of metal retainers as shown in the above illustrations. 5) Install the new blade in the reverse order of removal, with the locked end positioned toward the wiper arm. Make sure the blade is properly retained by all the hooks. Lock the blade end into place. 6) Reinstall wiper frame to arm, making sure that the lock lever is snapped securely into the arm. (3) 60MH071 80G146 1) Hold the wiper arm away from the window. 2) Remove the wiper frame from the arm as shown. 3) Slide the blade out as shown. 168 7-30 76MH1-74E INSPECTION AND MAINTENANCE 76MH1-74E 4) If the new blade is provided without the two metal retainers, move them from the old blade to the new one. 5) Install the new blade in the reverse order of removal. Make sure the blade is properly retained by all the hooks. 6) Reinstall wiper frame to arm in the reverse order of removal. WARNING Do not use “antifreeze” solution in the windshield washer reservoir. This can severely impair visibility when sprayed on the windshield, and can also damage your vehicle’s paint. NOTICE Windshield Washer Fluid Front EXAMPLE 65D151 Damage may result if the washer motor is operated with no fluid in the washer tank. Air Conditioning System NOTE: Do not flex the wiper blade frame end more than necessary. If you do, it can break off. 80JM078 If you do not use the air conditioner for a long period, such as during winter, it may not give the best performance when you start using it again. To help maintain optimum performance and durability of your air conditioner, it needs to be run periodically. Operate the air conditioner at least once a month for one minute with the engine idling. This circulates the refrigerant and oil and helps protect the internal components. Check that there is washer fluid in the tank. Refill it if necessary. Use a good quality windshield washer fluid, diluted with water as necessary. 54G135 (1) Retainer 169 7-31 76MH1-74E 76MH1-74E EMERGENCY SERVICE EMERGENCY SERVICE Tire Changing Tool ............................................................. 8-1 Jacking Instructions ........................................................... 8-1 Changing Wheels ................................................................ 8-3 Jump Starting Instructions ................................................ 8-4 Towing .................................................................................. 8-5 If the Starter Does Not Operate .......................................... 8-6 If the Engine is Flooded ...................................................... 8-6 If the Engine Overheats ...................................................... 8-6 170 76MH1-74E EMERGENCY SERVICE 76MH1-74E Tire Changing Tool WARNING WARNING After using the tire changing tools, be sure to stow them securely or they can cause injury if an accident occurs. EXAMPLE CAUTION The jack should be used only to change wheels. It is important to read the jacking instructions in this section before attempting to use the jack. 76MH1004 The jack, wheel wrench and jack handle are stowed in the luggage compartment. Jacking Instructions • Be sure to shift into “R” (Reverse) when you jack up the vehicle. • Never jack up the vehicle with the transaxle in “N” (Neutral). Otherwise, unstable jack may cause an accident. 3) Turn on the hazard warning flasher if your vehicle is near traffic. 4) Block the front and rear of the wheel diagonally opposite of the wheel being lifted. 5) Place the spare wheel near the wheel being lifted as shown in the illustration in case that the jack slips. EXAMPLE 52KM119 (1) 76MH0A129 To remove the spare tire, turn its bolt (1) counterclockwise and remove it. 1) Place the vehicle on level, hard ground. 2) Set the parking brake firmly and shift into “R” (Reverse). 54G253 171 8-1 76MH1-74E EMERGENCY SERVICE 76MH1-74E around the jacking bar beneath the vehicle body. See illustrations. 7) Continue to raise the jack slowly and smoothly until the tire clears the ground. Do not raise the vehicle more than necessary. EXAMPLE WARNING 63J100 EXAMPLE • Use the jack only to change wheels on level, hard ground. • Never jack up the vehicle on an inclined surface. • Never raise the vehicle with the jack in a location other than the specified jacking point (shown in the illustration) near the wheel to be changed. • Make sure that the jack is raised at least 51 mm (2 inches) before it contacts the flange. Use of the jack when it is within 51 mm (2 inches) of being fully collapsed may result in failure of the jack. • Never get under the vehicle when it is supported by the jack. • Never run the engine when the vehicle is supported by the jack and never allow passengers to remain in the vehicle. To Raise the Vehicle with a Garage Jack • Apply the garage jack to one of the points indicated below. • Always support the raised vehicle with jack stands (commercially available) at the points indicated below . Front jacking point for garage jack (1) EXAMPLE 63J101 6) Position the jack vertically and raise the jack by turning the jack handle clockwise until the jack head groove fits (1) 172 8-2 76MH1-74E EMERGENCY SERVICE 76MH1-74E Rear jacking point for garage jack (2) NOTICE Never apply a garage jack to the exhaust pipe, side under spoiler (if equipped), engine undercover or rear torsion beam. Loosen Tighten NOTE: For more details, please contact an authorized MARUTI SUZUKI dealer. Changing Wheels (2) EXAMPLE To change a wheel, use the following procedure: 54G116 76MH0A078 Application point for jack stand (3) or two-column lift EXAMPLE (3) (3) 61MM0B103 1) Clear all passengers and luggage from the vehicle. 2) Remove the jack, tools and spare wheel from the vehicle. 3) Loosen, but do not remove the wheel nuts. 4) Jack up the vehicle. 5) Remove the wheel nuts and wheel. 6) Before installing the new wheel, clean any mud or dirt off from the surface of the wheel and hub with a clean cloth. Clean the hub carefully; it may be hot from driving. 7) Install the new wheel and replace the wheel nuts with their cone shaped end facing the wheel. Tighten each nut snugly by hand until the wheel is securely seated on the hub. Tightening torque for wheel nut 85 Nm (8.7 kg-m, 62.7 lb-ft) 8) Lower the jack and fully tighten the nuts in a crisscross fashion with a wrench as shown in the illustration. WARNING Use genuine wheel nuts and tighten them to the specified torque as soon as possible after changing wheels. Incorrect wheel nuts or improperly tightened wheel nuts may come loose or fall off, which can result in an accident. If you do not have a torque wrench, have the wheel nut torque checked by an authorized MARUTI SUZUKI dealer. 173 8-3 76MH1-74E EMERGENCY SERVICE 76MH1-74E Jump Starting Instructions Full Wheel Cover (if equipped) EXAMPLE WARNING 60G309 Insert a piece of cloth between the spokes of the wheel cover and try to pull the cover outward (as shown in figure). Take out the detached wheel cover from the wheel rim. For installation first match the slot at the wheel cover with the air filling nozzle of the wheel. Apply equal pressure at the circumference of the wheel cover to fix it in the wheel rim. EXAMPLE 74LHT0860 When installing the cover, make sure that it is positioned so that it does not cover or foul the air valve. • Never attempt to jump start your vehicle if the battery appears to be frozen. Batteries in this condition may explode or rupture if jump starting is attempted. • When making jump lead connections, be certain that your hands and the jump leads remain clear from pulleys, belts, or fans. • Batteries produce flammable hydrogen gas. Keep flames and sparks away from the battery or an explosion may occur. Never smoke when working in the vicinity of the battery. • If the booster battery you use for jump starting is installed in another vehicle, make sure the two vehicles are not touching each other. • If your battery discharges repeatedly, for no apparent reason, have your vehicle inspected by an authorized MARUTI SUZUKI dealer. • To avoid harm to yourself or damage to your vehicle or battery, follow the jump starting instructions below precisely and in order. If you are in doubt, call for qualified road service. NOTICE Your vehicle should not be started by pushing or towing. This starting method could result in permanent damage to the catalytic converter. Use jump leads to start a vehicle with a weak or flat battery. When Jump Starting Your Vehicle, Use the Following Procedure: 1) Use only a 12-volt battery to jump start your vehicle. Position the good 12-volt battery close to your vehicle so that the jump leads will reach both batteries. When using a battery installed on another vehicle, DO NOT LET THE VEHICLES TOUCH. Set the parking brakes fully on both vehicles. 2) Turn off all vehicle accessories, except those necessary for safety reasons (for example, headlights or hazard lights). (1) 4 1 (3) EXAMPLE 3 2 (2) 54MN259 174 8-4 76MH1-74E EMERGENCY SERVICE 76MH1-74E 3) Make jump lead connections as follows: 1. Connect one end of the first jump lead to the positive (+) terminal of the flat battery (1). 2. Connect the other end to the positive (+) terminal of the booster battery (2). 3. Connect one end of the second jump lead to the negative (–) terminal of the booster battery (2). 4. Make the final connection to an unpainted, heavy metal part (i.e. engine mount bracket (3)) of the engine of the vehicle with the flat battery (1). WARNING Never connect the jump lead directly to the negative (–) terminal of the discharged battery, or an explosion may occur. CAUTION Connect the jump lead to the engine mount bracket securely. If the jump lead disconnects from the engine mount bracket because of vibration at the start of the engine, the jump lead could be caught in the drive belts. 4) If the booster battery you are using is fitted to another vehicle, start the engine of the vehicle with the booster battery. Run the engine at moderate speed. 5) Start the engine of the vehicle with the flat battery. 6) Remove the jump leads in the exact reverse order in which you connected them. Towing If you need to have your vehicle towed, contact a professional service. Your dealer can provide you with detailed towing instructions. NOTICE To help avoid damage to your vehicle during towing, proper equipment and towing procedures must be used. 2-Wheel Drive (2WD) Manual Transaxle or Auto Gear Shift Manual transaxle vehicles or Auto Gear Shift vehicles may be towed using either of the following methods. 1) From the front, with the front wheels lifted and the rear wheels on the ground. Before towing, make sure that the parking brake is released. 2) From the rear, with the rear wheels lifted and the front wheels on the ground, provided the steering and drivetrain are in operational condition. Before towing, make sure that transaxle is in neutral, the steering wheel is unlocked (the ignition key should be in the “ACC” position), and the steering wheel is secured with a clamping device designed for towing service. NOTICE After shifting the Auto Gear Shift lever to the “N” position, always check the gear position indicator in the instrument cluster shows the “N” position to make sure that the transaxle is disengaged. If the transaxle cannot be put in neutral, turn the key from the “LOCK” to the “ON” position, and move the Auto Gear Shift lever from “N” to “D”, “M” or “R”, then back to “N” again. Then turn the key from the “ON” to the “LOCK” position. These procedures may help put the transaxle in neutral. If the transaxle still cannot be put in neutral, you cannot tow the vehicle without using a towing dolly. The steering column is not strong enough to with stand shocks transmitted from the front wheels during towing. Always unlock the steering wheel before towing. 175 8-5 76MH1-74E EMERGENCY SERVICE If the Starter Does Not Operate 1) Try turning the ignition switch to the “START” position with the headlights turned on to determine the battery condition. If the headlights go excessively dim or go off, it usually means that either the battery is flat or the battery terminal contact is poor. Recharge the battery or correct battery terminal contact as necessary. 2) If the headlights remain bright, check the fuses. If the reason for failure of the starter is not obvious, there may be a major electrical problem. Have the vehicle inspected by your authorized MARUTI SUZUKI dealer. If the Engine is Flooded If the engine is flooded with petrol, it may be hard to start. If this happens, press the accelerator pedal all the way to the floor and hold it there while cranking the engine. • For petrol engine model, do not operate the starter motor for more than 12 seconds. • For diesel engine model, do not operate the starter motor for more than 30 seconds. 76MH1-74E If the Engine Overheats The engine could overheat temporarily under severe driving conditions. If the high engine coolant temperature warning light comes on as overheating during driving: 1) Turn off the air conditioner, if equipped. 2) Take the vehicle to a safe place and park. 3) Let the engine run at the normal idle speed for a few minutes until the high engine coolant temperature warning light goes off. WARNING If you see or hear escaping steam, stop the vehicle in a safe place and immediately turn off the engine to let it cool. Do not open the hood when steam is present. When the steam can no longer be seen or heard, open the hood to see if the coolant is still boiling. If it is, you must wait until it stops boiling before you proceed. 2) Check the coolant level in the reservoir. If it is found to be lower than the “LOW” line, look for leaks at the radiator, water pump, and radiator and heater hoses. If you locate any leaks that may have caused the overheating, do not run the engine until these problems have been corrected. 3) If you do not find a leak, carefully add coolant to the reservoir and then the radiator, if necessary. (Refer to “Engine Coolant” in the “INSPECTION AND MAINTENANCE” section.) NOTE: If your engine overheats and you are unsure what to do, contact your MARUTI SUZUKI dealer. If the high engine coolant temperature warning light does not go off: 1) Turn off the engine and check that the water pump belt and pulleys are not damaged or slipping. If any abnormality is found, correct it. 176 8-6 76MH1-74E EMERGENCY SERVICE 76MH1-74E Warning Triangle EXAMPLE MHO-07-001 65D614 WARNING • It is hazardous to remove the radiator cap (or degassing tank cap for a diesel engine) when the water temperature is high, because scalding fluid and steam may be blown out under pressure. The cap should only be taken off when the coolant temperature has lowered. • To help prevent personal injury, keep hands, tools and clothing away from the engine cooling fan and air-conditioner fan (if equipped). These electric fans can automatically turn on without warning. In case of vehicle break-down or during emergency stopping, where, your vehicle could become a potential traffic hazard, keep the warning triangle, provided with your vehicle, on the road free from any obstacles behind your vehicle so as to warn the approaching traffic, at an approximate distance of 50-100 m. The reflecting side of the triangle should face the on coming traffic. Please activate the hazard warning lamps before alighting the vehicle to keep the warning triangle. • Remove the warning triangle carefully from the cover as shown by arrow 1. • Open both the reflector arms as shown by arrow and lock the arms with each other with the clip provided in the right arm. Open the bottom stand in counter clock-wise direction as shown by arrow 3. Position the warning triangle behind the vehicle on a plain surface. • Reverse the removal procedure for keeping inside the cover. MHO-07-014 MHO-07-014 177 8-7 76MH1-74E 76MH1-74E APPEARANCE CARE APPEARANCE CARE Corrosion Prevention ......................................................... 9-1 Vehicle Cleaning ................................................................. 9-2 178 76MH1-74E APPEARANCE CARE 76MH1-74E APPEARANCE CARE Corrosion Prevention It is important to take good care of your vehicle to protect it from corrosion. Listed below are instructions for how to maintain your vehicle to prevent corrosion. Please read and follow these instructions carefully. Important Information About Corrosion Common causes of corrosion 1) Accumulation of road salt, dirt, moisture, or chemicals in hard-to-reach areas of the vehicle underbody or frame. 2) Chipping, scratches and any damage to treated or painted metal surfaces resulting from minor accidents or abrasion by stones and gravel. Environmental conditions which accelerate corrosion 1) Road salt, dust control chemicals, sea air or industrial pollution will all accelerate the corrosion of metal. 2) High humidity will increase the rate of corrosion particularly when the temperature range is just above the freezing point. 3) Moisture in certain areas of a vehicle for an extended period of time may promote corrosion even though other body sections may be completely dry. 4) High temperatures will cause an accelerated rate of corrosion to parts of the vehicle which are not well ventilated to permit quick drying. is not harmful to painted surfaces and is specifically intended for your purposes. Follow the manufacturer’s directions when using these special cleaners. This information illustrates the necessity of keeping your vehicle (particularly the underbody) as clean and dry as possible. It is equally important to repair any damage to the paint or protective coatings as soon as possible. Repair finish damage Carefully examine your vehicle for damage to the painted surfaces. Should you find any chips or scratches in the paint, touch them up immediately to prevent corrosion from starting. If the chips or scratches have gone through to the bare metal, have a qualified body shop make the repair. How to Help Prevent Corrosion Wash your vehicle frequently The best way to preserve the finish on your vehicle and to help avoid corrosion is to keep it clean with frequent washing. Wash your vehicle at least once during the winter and once immediately after the winter. Keep your vehicle, particularly the underside, as clean and dry as possible. If you frequently drive on salted roads, your vehicle should be washed at least once a month during the winter. If you live near the ocean, your vehicle should be washed at least once a month throughout the year. For washing instructions, refer to the “Vehicle Cleaning” section. Remove foreign material deposits Foreign material such as salts, chemicals, road oil or tar, tree sap, bird droppings and industrial fall-out may damage the finish of your vehicle if it is left on painted surfaces. Remove these types of deposits as quickly as possible. If these deposits are difficult to wash off, an additional cleaner may be required. Be sure that any cleaner you use Keep passenger and luggage compartments clean Moisture, dirt or mud can accumulate under the floor mats and may cause corrosion. Occasionally, check under these mats to ensure that this area is clean and dry. More frequent checks are necessary if the vehicle is used off road or in wet weather. Certain cargos such as chemicals, fertilizers, cleaners, salts, etc. are extremely corrosive by nature. These products should be transported in sealed containers. If a spill or leak does occur, clean and dry the area immediately. Store your vehicle in a dry, well-ventilated area Do not park your vehicle in a damp, poorly ventilated area. If you often wash your vehicle in the garage or if you frequently drive it in when wet, your garage may be damp. The high humidity in the garage may cause or accelerate corrosion. A wet vehicle may corrode even in a heated garage if the ventilation is poor. 179 9-1 76MH1-74E APPEARANCE CARE 76MH1-74E Cleaning the Interior WARNING Do not apply additional undercoating or rust preventive coating on or around exhaust system components such as the catalytic converter, exhaust pipes, etc. A fire could be started if the undercoating substance becomes overheated. Vehicle Cleaning Vinyl upholstery Prepare a solution of soap or mild detergent mixed with warm water. Apply the solution to the vinyl with a sponge or soft cloth and let it soak for a few minutes to loosen dirt. Rub the surface with a clean, damp cloth to remove dirt and the soap solution. If some dirt still remains on the surface, repeat this procedure. Fabric upholstery Remove loose dirt with a vacuum cleaner. Using a mild soap solution, rub stained areas with a clean damp cloth. To remove soap, rub the areas again with a cloth dampened with water. Repeat this until the stain is removed, or use a commercial fabric cleaner for tougher stains. If you use a fabric cleaner, carefully follow the manufacturer’s instructions and precautions. 76G044S WARNING When cleaning the interior or exterior of the vehicle, NEVER USE flammable solvents such as lacquer thinners, petrol, benzene or cleaning materials such as bleaches or strong household detergents. The materials could cause personal injury or damage to the vehicle. Seat belts Clean seat belts with a mild soap and water. Do not use bleach or dye on the belts. They may weaken the fabric in the belts. Vinyl floor mats Ordinary dirt can be removed from vinyl with water or mild soap. Use a brush to help loosen dirt. After the dirt is loosened, rinse the mat thoroughly with water and dry it in the shade. Carpets Remove dirt and soil as much as possible with a vacuum cleaner. Using a mild soap solution, rub stained areas with a clean damp cloth. To remove soap, rub the areas again with a cloth dampened with water. Repeat this until the stain is removed, or use a commercial carpet cleaner for tougher stains. If you use a carpet cleaner, carefully follow the manufacturer’s instructions and precautions. Instrument panel and console Remove loose dirt with a vacuum cleaner. Gently wipe dirt off with a tightly squeezed damp clean cloth. Repeat this until the dirt is removed. NOTICE Do not use chemical products that contain silicon to wipe electrical components such as the air conditioning system, audio, navigation system, or other switches. These will cause damage to the components. Cleaning the Exterior NOTICE It is important that your vehicle be kept clean and free from dirt. Failure to keep your vehicle clean may result in fading of the paint or corrosion to various parts of the vehicle body. 180 9-2 76MH1-74E APPEARANCE CARE 76MH1-74E Caring for Aluminum Wheels NOTE: • Do not use an acidic or alkaline detergent to wash aluminum wheels. These types of detergent will cause permanent spots, discoloration and cracks on finished surfaces. • Do not use a bristle brush and soap containing an abrasive material. These will damage finished surfaces. Washing WARNING • Never attempt to wash and wax your vehicle with the engine running. • When cleaning the underside of the body and fender, where there may be sharp-edged parts, you should wear gloves and a long-sleeved shirt to protect your hands and arms from being cut. • After washing your vehicle, carefully test the brakes before driving to make sure they have maintained their normal effectiveness. When washing the vehicle, park it where direct sunlight does not fall on it and follow the instructions below: 1) Flush the underside of body and wheel housings with pressurized water to remove mud and debris. Use plenty of water. NOTICE 60B212S When washing the vehicle: • Avoid directing steam or hot water of more than 80°C (176°F) on plastic parts. • To avoid damaging engine components, do not use pressurized water in the engine compartment. 2) Rinse the body to loosen the dirt. Remove dirt and mud from the body exterior with running water. You may use a soft sponge or brush. Do not use hard materials which can scratch the paint or plastic. Remember that the headlight covers or lenses are made of plastic in many cases. NOTICE To avoid damage to the paint or plastic surface, do not wipe the dirt off without ample water. Be sure to follow above procedure. 3) Wash the entire exterior with a mild detergent or car wash soap using a sponge or soft cloth. The sponge or cloth should be frequently soaked in the soap solution. NOTICE When using a commercial car wash product, observe the cautions specified by the manufacturer. Never use strong household detergents or soaps. 4) Once the dirt has been completely removed, rinse off the detergent with running water. 5) After rinsing, wipe off the vehicle body with a wet chamois or cloth and allow it to dry in the shade. 6) Check carefully for damage to painted surfaces. If there is any damage, “touch-up” the damage following the procedure below: 181 9-3 76MH1-74E APPEARANCE CARE 1. Clean all damaged spots and allow them to dry. 2. Stir the paint and “touch-up” the damaged spots lightly using a small brush. 3. Allow the paint to dry completely. 76MH1-74E Waxing NOTICE If you use an automatic car wash, make sure that your vehicle’s body parts, such as spoilers, cannot be damaged. If you are in doubt, consult the car wash operator for advice. 60B211S After washing the vehicle, waxing and polishing are recommended to further protect and beautify the paint. • Only use waxes and polishes of good quality. • When using waxes and polishes, observe the precautions specified by the manufacturers. 182 9-4 76MH1-74E GENERAL INFORMATION 76MH1-74E GENERAL INFORMATION Engine Serial Number Vehicle Identification Chassis Serial Number EXAMPLE 54G082 The engine serial number is stamped on the cylinder block as shown in the illustration. 68KH096 The chassis and/or engine serial numbers are used to register the vehicle. They are also used to assist your dealer when ordering or referring to special service information. Whenever you have occasion to consult your MARUTI SUZUKI dealer, remember to identify your vehicle with this number. Should you find the number difficult to read, you will also find it on the identification plate. 183 10-1 76MH1-74E GENERAL INFORMATION 76MH1-74E Radio frequency identification (RFID) tag (if equipped) As seen from inside of the vehicle As seen from outside of the vehicle As per Ministry of Road Transport and Highways, the Radio frequency identification (RFID) tag (1) is mandatory for each vehicle for the purpose of electronic toll collection or any other purpose as may be defined by the Government of India. In case of any damage to RFID tag or replacement of front windscreen, please contact your nearest MARUTI SUZUKI Authorized workshop. (1) 76MH1001 10-2 76MH1002 76MH1003 NOTE: The picture shown is for indicative purpose only. Internal structure of actual device mounted on vehicle may be different. NOTE: The picture shown is for indicative purpose only. Internal structure of actual device mounted on vehicle may be different. NOTE: • RFID tag needs to be registered by government authorized agency (if applicable). • Any attempt to remove the tag from the windscreen will result in permanent damage to the tag. • Use of chemical cleaners to clean the windscreen area where the tag is mounted can damage the tag. • Use of any sharp objects on the tag can damage the tag. 184 76MH1-74E SPECIFICATIONS 76MH1-74E SPECIFICATIONS NOTE: Specifications are subject to change without notice. ITEM: Dimensions M/T: Manual transaxle Petrol: Petrol engine model Diesel: Diesel engine model UNIT: mm Overall length 3600 Overall width 1600 Overall height 1560 Wheelbase Track 2425 Front 1420 Rear 1410 Ground clearance 165 ITEM: Mass (weight) Curb mass (weight) UNIT: kg PETROL ENGINE MODEL DIESEL ENGINE MODEL M/T 810 - 830 880 - 900 Auto Gear Shift 815 - 830 – Gross vehicle mass (weight) rating Permissible maximum Axle Weight 1250 1310 Front 680 720 Rear 640 640 185 11-1 76MH1-74E SPECIFICATIONS 76MH1-74E ITEM: Engine Type K10B (DOHC) E08A 3 2 Bore 73.0 mm 77.0 mm Stroke 79.5 mm 85.1 mm cm3 793 cm3 Number of cylinders Piston displacement 998 Compression ratio 11.0 ± 0.4: 1 15.1 ± 0.4: 1 ITEM: Electrical Standard spark plug Petrol NGK KR6A-10 Battery Petrol 12V 34B19L Diesel 12V 55B24L Fuses See “INSPECTION AND MAINTENANCE” section. 186 11-2 76MH1-74E SPECIFICATIONS 76MH1-74E ITEM: Lights WATTAGE BULB No. Headlight 12V 60/55W H4 Front fog light (if equipped) 12V 35W H8 Position light Turn signal light 12V 5W W5W Front 12V 21W PY21W Rear 12V 21W PY21W Side turn signal light 12V 5W WY5W LED – Brake/tail light 12V 21/5W P21/5W High mount stop light 12V 5W W5W Reversing light 12V 21W P21W License plate light 12V 5W W5W Interior light 12V 10W – 187 11-3 76MH1-74E SPECIFICATIONS 76MH1-74E ITEM: Wheels and Tires Tire size 155/80R13 79S*1, 165/70R14 81S*1*2 Rim size 13 × 4 1/2J (For R13 tire) 14 × 5J (For R14 tire) Tire pressures For the specified tire pressure, see the Tire Information Label located on the driver’s door lock pillar. *1: When tire replacement is necessary and if the specified load index and speed rated tire is not available, then use a tire of higher load index and speed rating. *2: The spare wheel provided with alloy wheel variant is steel wheel rim, hence follow 4 tire rotation only. (Refer: under section “Inspection and maintenance”) ITEM: Recommended Fuel/Lubricants and Capacities (approx.) Fuel Engine oil Coolant (including reservoir tank) Manual transaxle oil 11-4 35 L Petrol 2.8 L (replacement with oil filter) Diesel 3.4 L (replacement with oil filter) Petrol 3.3 L Diesel 3.6 L Petrol 1.45 L Diesel 2.0 L 188 76MH1-74E This Owner’s manual & service booklet applies to CELERIO models produced by MARUTI SUZUKI INDIA LIMITED. Prepared by MARUTI SUZUKI INDIA LIMITED Service Division March, 2015 Part No. 99011M76M02-74E Printed in India Note : The illustrated model is one of the CELERIO series Accessories shown in the picture are not part of standard equipment c COPYRIGHT MARUTI SUZUKI INDIA LIMITED 2015 For round-the-clock on-road assistance, call Maruti On-road Service at 1800 102 1800# #No STD code to be prefixed. This Owner’s manual & service booklet applies to CELERIO models produced by MARUTI SUZUKI INDIA LIMITED. Prepared by MARUTI SUZUKI INDIA LIMITED Service Division March, 2015 Part No. 99011M76M03-74E Printed in India Note : The illustrated model is one of the CELERIO series Accessories shown in the picture are not part of standard equipment c COPYRIGHT MARUTI SUZUKI INDIA LIMITED 2015 For round-the-clock on-road assistance, call Maruti On-road Service at 1800 102 1800# #No STD code to be prefixed. India's No. 1 Car Exchange Programme OWNER'S MANUAL & SERVICE BOOKLET ER E AU CODE 02/03/2015/5000 Palam Gurgaon Road, Gurgaon - 122 015 (Haryana) www.marutisuzuki.com ED MARUTI SUZUKI INDIA LIMITED O RI S TH S Service Division 99011M76M02-74E 1800 102 1800 PEACE OF MIND Keep With Vehicle At All Times. Contains Important Information On Safety, Operation & Maintenance. VIC Part No. 99011M76M02-74E ENG. March, 2015 India's No. 1 Car Exchange Programme OWNER'S MANUAL & SERVICE BOOKLET ER E AU CODE 02/03/2015/5000 ED MARUTI SUZUKI INDIA LIMITED Palam Gurgaon Road, Gurgaon - 122 015 (Haryana) www.marutisuzuki.com O RI S TH S Service Division 99011M76M03-74E 1800 102 1800 PEACE OF MIND Keep With Vehicle At All Times. Contains Important Information On Safety, Operation & Maintenance. VIC Part No. 99011M76M03-74E ENG. March, 2015