Toyota - RAV4 - Workshop Manual - 2006 - 2006

TOYOTA RAV4 2006 - 2007 TVIP V5 Preparation RS3200PLUS NOTE: Part number of this accessory may not be the same as the part number shown. Part Number: 08586-42810 Kit Contents Item # 1 2 3 4 5 6 Quantity Reqd. 1 1 1 1 1 1 Description Wire Harness GBS ECU Security ECU Mounting Bracket GBS ECU Mounting Bracket Status Monitor Security ECU Special Chemicals Notes Glass Cleaner Cleaner Household Windex 3M™ Prep Sol-70 General Applicability Note: Rav4 with factory keyless entry system only. Recommended Sequence of Application Item # Accessory Hardware Bag Contents Item # 1 2 3 4 5 6 7 8 9 Quantity Reqd. 1 20 1 1 2 2 2 1 1 Description Small Foam Tape Strip Wire Ties Large Foam Tape (2 per.) Clip Butyl Tape Warning Labels (English) Warning Labels (Spanish) Owner’s Manual Warranty Card Additional Items Required For Installation Item # Quantity Reqd. Description Conflicts Note: Must not be installed in vehicles with factory Antitheft alarm. Recommended Tools Personal & Vehicle Protection *Mandatory Vehicle Service Parts (may be required for reassembly) Item # 1 (Optional) Blankets, Part Boxes Special Tools Notes Striker Tool (PPO only) CAD-E IADS P/N: ALL 02-016-01 Installation Tools Notes Phillips Head Screwdriver Flat Blade Screwdriver Socket Nylon Panel Removal Tool #2, screwdriver or tip Small 10 mm, 12 mm e.g. Panel Pry Tool #1 STOP: Damage to the vehicle may occur. Do not proceed until process has been complied with. OPERATOR SAFETY: Use caution to avoid risk of injury. CAUTION: A process that must be carefully observed in order to reduce the risk of damage to the accessory/vehicle and to ensure a quality installation. TOOLS & EQUIPMENT: Used in Figures calls out the specific tools and equipment recommended for this process. REVISION MARK: This mark highlights a change in installation with respect to previous issue. Toyota SST # 00002-06001-01 Pneumatic/Electric Wrench Wrench Torque Wrench 10 mm 2.9 ~ 4.9N·m (26.0 ~ 43.4 lbf ft) Side Cutters Issue: D 02/06/08 Description #45286-42915-BO Lower Steering Column Cover Legend Notes Safety Glasses Safety Gloves Vehicle Protection Quantity Reqd. 1 Page 1 of 20 pages TOYOTA RAV4 2006 - 2007 Procedure TVIP V5 RS3200PLUS Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation. These guidelines can be found in the "Accessory Installation Practices" document. This document covers such items as:• Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). • Safety (eye protection, rechecking torque procedure, etc.). • Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). • Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Toyota dealer for a copy of this document. Negative Battery Cable 10mm Wrench The differences are highlighted in the procedure as follows:• Plain text used for V5 system installation (no text box). • Shaded text box used for both V5 harness and V4 harness installation. Battery Fig. 1-1 NOTE: This installation instructions covers both V5 harness and V4 harness installation. 1. Vehicle Disassembly. Nylon Panel Removal Tool (a) Remove the negative battery cable. (Fig. 1-1) (1) Protect the fender before starting. Step Cover (2) Do not touch the positive terminal with any tool removing the cable. (b) Remove the driver’s step cover. (Fig. 1-2) Fig. 1-2 (c) Remove the driver’s cowl cover. (Fig. 1-3) (1) Remove one nut securing the cowl cover. Cowl Cover Nut Fig. 1-3 Issue: D 02/06/08 Page 2 of 20 pages TOYOTA RAV4 2006 - 2007 Procedure TVIP V5 RS3200PLUS (d) Remove the fuse box cover. (Fig. 1-4) Phillips Screwdriver (e) Remove the instrument lower panel. (Fig. 1-4) Lower Panel Fuse Box Cover (1) Remove two screws securing the panel. Screws (x2) Fig. 1-4 Nylon Panel Removal Tool (f) Remove the steering column lower cover. (Fig. 1-5) Note: Should damage occur please see TSB ST006-06 for additional information. Steering Column Lower Cover Fig. 1-5 Nylon Panel Removal Tool (g) Remove the glove box under cover. (Fig. 1-6) Glove Box Under Cover Fig. 1-6 Nylon Panel Removal Tool Dumper Lever (h) Remove the glove box assembly. (Fig. 1-7) (1) Open the glove box door and release the dumper lever from the glove box assembly. Glove Box Fig. 1-7 Issue: D 02/06/08 Page 3 of 20 pages TOYOTA RAV4 2006 - 2007 Procedure TVIP V5 RS3200PLUS (i) Remove the passenger’s step cover. (Fig. 1-8) Nylon Panel Removal Tool Step Cover Fig. 1-8 (j) Remove the passenger’s cowl cover. (Fig. 1-9) Cowl Cover Nut Fig. 1-9 Side Cutter 2. V5 Harness Installation. Vehicle Harness Clamp Wire Ties (x3) V5 Harness’ White Tape (b) Secure the V5 harness to the vehicle harness white two wire ties. (Fig. 2-1) Side Cutter V5 Harness V5 harness Fig. 2-2 4P (White) 02/06/08 (a) Locate the vehicle harness clamp on the steering shaft area. Secure the white taped marker of the V5 harness next to the vehicle harness clamp with one wire tie. (Fig. 2-1) (1) Line up the V5 harness’ white tape marker to the vehicle harness clamp. V5 Harness’ Fig. 2-1 Issue: D (1) Remove one nut securing the cowl cover. (c) Route the V5 harness toward the driver side J/B area, the secure it to the vehicle harness with two wire ties. (Fig. 2-2) Wire Tie (x2) Page 4 of 20 pages TOYOTA RAV4 2006 - 2007 Procedure TVIP V5 RS3200PLUS (d) Route the V5 harness’ white 18P connectors toward the driver side J/B area, then secure it to the vehicle harness with one wire tie. (Fig. 2-3) Side Cutter Go to Step l. Wire Tie V5 Harness V5 harness’ Fig. 2-3 18P (White) FOR V5 HARNESS and V4 HARNESS SIMULTANEOUS INSTALLATION ONLY. (Steps e-g) V5 Harness NOTE: Only perform this installation step on the V5 harness and V4 harness installed simultaneously. (e) Locate and disconnect the black 4P connector on the V5 harness to separate the harness portions. (Fig. 2-4) 4P Connector (Black) 8P Connector (White) (1) Discard the separated harness (4P male connector and 8P connectors). Fig. 2-4 (f) Locate and disconnect the black 4P female connector plugged into the V4 harness’ black 4P male connector. (Fig. 2-5) 4P Connector (Black) (1) Discard the black 4P female connector. V4 Harness Fig. 2-5 (g) Connect the V5 harness’ black 4P female connector and the V4 harness’ black 4P male connector. (Fig. 2-6) V4 Harness V5 Harness 4P Connector (Black) Fig. 2-6 Issue: D 02/06/08 Page 5 of 20 pages TOYOTA RAV4 2006 - 2007 Procedure TVIP V5 RS3200PLUS Vehicle Harness Clamp Side Cutter Wire Tie V4 Harness’ V5 Harness’ 4P V4 Harness and V5 Harness’ White Tape V4 Harness’ 4P Fig. 2-7 Wire Tie Side Cutter Wire Tie V4 Harness and V5 Harness V4 Harness’ RED Wire V4 Harness’ 18P (white) V5 Harness’ 18P (white) Fig. 2-8 NOTE: Only perform this installation step on the V5 harness and V4 harness installed simultaneously. (h) Locate the vehicle’s harness clamp on the steering column area. Secure the V5 harness and V4 harness’ white tape to the vehicle harness clamp with one wire tie. (Fig. 2-7) V4 Harness’ Fuses V5 Harness’ 4P (white) FOR V5 HARNESS and V4 HARNESS SIMULTANEOUS INSTALLATION ONLY. (Steps h-k) Backside of the Driver Side J/B (i) Secure the V5 harness and V4 harness’ two fuses to the vehicle harness with one wire tie. (Fig. 2-7) (j) Route the V5 harness and V4 harness toward the driver side J/B area, then secure it to the vehicle harness with one wire tie. (Fig. 2-8) (k) Route the V5 harness’ white 4P connector toward the driver side J/B area as shown. (Fig. 2-8) (l) Locate and disconnect the white 18P connector from the backside of the driver side J/B in the bottom of the second space from the left. (Fig. 2-9) Driver Side J/B 18P (White) Fig. 2-9 Side Cutter (m) Route the V5 harness toward the backside of the driver side J/B. (Fig. 2-10) Backside of the J/B V5 Harness V5 Harness’ 18P Vehicle Harness’ 18P Fig. 2-10 Issue: D V5 Harness’ 18P 02/06/08 (n) Plug in the V5 harness' white 18P connectors between the vehicle's harness 18P connector and the backside of the driver side J/B. (Fig. 2-10) (1) Verify the connectors are plugged in securely. Page 6 of 20 pages TOYOTA RAV4 2006 - 2007 Procedure TVIP V5 RS3200PLUS V5 Harness Side Cutter Backside of J/B (o) Secure the 18P connectors to the vehicle harness with one wire tie. (Fig. 2-11) Go to Step s. FOR V5 HARNESS and V4 HARNESS SIMULTANEOUS INSTALLATION ONLY. (Steps p-r) 18P Wire Tie NOTE: Only perform this installation step on the V5 harness and V4 harness installed simultaneously. 18P Fig. 2-11 V4 Harness and V5 Harness (p) Connect the V4 harness’ white 18P male connector to the V5 harness’ white 18P female connector. (Fig. 2-12) Backside of the J/B 18P 18P 18P V5 Harness V4 Harness Fig. 2-12 V5 Harness’ 18P Vehicle Harness’ 18P (q) Plug in the V5 harness’ white 18P connector into the driver side J/B. Then connect the V4 harness’ white 18P connector to the vehicle harness’ white 18P connector. (Fig. 2-12) (1) Verify the connectors are plugged in securely. Backside of J/B Side Cutter (r) Secure the two 18P connectors to the vehicle harness with one wire tie. (Fig. 2-13) V4 Harness and V5 Harness 18P 18P Wire Tie 18P Fig. 2-13 (s) Locate and disconnect the white 2P and white 8P connector from the ignition switch area. (Fig. 2-14) 2P (white) Fig. 2-14 Issue: D 02/06/08 8P (white) Page 7 of 20 pages TOYOTA RAV4 2006 - 2007 Procedure TVIP V5 RS3200PLUS (t) Plug in the V5 harness’ white 2P connectors between the vehicle harness’ 2P connector and the ignition switch. (Fig. 2-15) V5 Harness’ 2P V5 Harness Vehicle Harness’ 2P Fig. 2-15 V5 Harness’ 2P V5 Harness’ 8P Vehicle Harness’ 8P V5 Harness (u) Plug in the V5 harness’ white 8P connectors between the vehicle harness’ 8P connector and the ignition switch. (Fig. 2-16) Go to Step w. V5 Harness’ 8P FOR V5 HARNESS and V4 HARNESS SIMULTANEOUS INSTALLATION ONLY. (Step v) V5 Harness’ 4P (Black) Fig. 2-16 V4 Harness’4P (Black) V4 Harness’ 8P V4 Harness Vehicle Harness’ 8P Fig. 2-17 (v) Plug in the V4 harness’ white 8P connectors between the vehicle harness’ white 8P connector and the ignition switch. (Fig. 2-17) V5 Harness’ V4 Harness’ 8P 4P (Black) V5 Harness (w) Secure the 2P connectors and 8P connectors to the vehicle harness with two wire ties. (Fig. 2-18) Side Cutter Wire Tie NOTE: Only perform this installation step on the V5 harness and V4 harness installed simultaneously. 2P 8P (1) Do not secure the air bag yellow wires. Wire Tie Fig. 2-18 Issue: D 02/06/08 2P 8P Page 8 of 20 pages TOYOTA RAV4 2006 - 2007 Procedure TVIP V5 RS3200PLUS (x) Secure the V5 harness’ black 4P connectors to the vehicle harness with one wire tie. (Fig. 2-19) Side Cutter V5 Harness 4P 4P Fig. 2-19 V5 Harness Wire Tie Large Foam Tape V5 Harness' Relay (y) Locate the V5 harness' relay from the steering shaft area, then wrap the relay's metal part with large foam tape. (Fig. 2-20) Fig. 2-20 (z) Route the V5 harness toward the center cluster area, then secure it to the driver side metal brace with one wire tie. (Fig. 2-21) Brace Side Cutter Go to Step dd. Wire Tie Fig. 2-21 FOR V5 HARNESS and V4 HARNESS SIMULTANEOUS INSTALLATION ONLY. (Step aa) V5 harness NOTE: Only perform this installation step on the V5 harness and V4 harness installed simultaneously. V5 Harness’ Relay V5 Harness Fig. 2-22 Issue: D 02/06/08 V4 Harness’ Relay V4 Harness (aa) Locate the V4 harness’ relay and V5 harness’ relay from the steering column area, then secure the two relays with one large foam tape. (Fig. 2-22) Large Foam Tape Page 9 of 20 pages TOYOTA RAV4 2006 - 2007 Procedure TVIP V5 RS3200PLUS FOR V5 HARNESS and V4 HARNESS SIMULTANEOUS INSTALLATION ONLY. (Steps bb-cc) Brace Side Cutter V5 Harness and V4 harness NOTE: Only perform this installation step on the V5 harness and V4 harness installed simultaneously. Wire Tie (x3) 4P (Black) (bb) Route the V4 haness and V5 harness toward the center cluster area. (Fig. 2-23) 4P (Black) Fig. 2-23 (cc) Secure the black 4P connectors and relay to the V4 and V5 harness.with two wire ties. Secure the V4 harness and V5 harness to the driver side metal brace with one wire tie. (Fig. 2-23) (dd)Route the V5 harness (or V5 and V4 harness) toward the glove box area. (Fig. 2-24) V5 Harness or V5 and V4 Harness (1) Route the harness away from any moving parts such as levers, etc.. Fig. 2-24 (ee) Route the V5 harness to the glove box area, then secure it to the reinforcement with two wire ties. (Fig. 2-25) V5 Harness Side Cutter Wire Ties (x2) 3. V5 ECU and GBS ECU Preparation and Installation. 8P (White) Fig. 2-25 (a) Insert the V5 ECU mounting bracket into the indicated bracket slot on the V5 ECU. (Fig. 3-1) 40P (White) (1) Insert the mounting bracket into the correct ECU's slot. Clip V5 ECU Mounting Bracket V5 ECU (2) The bracket is permanently attached once installed. (3) Ensure the bracket is firmly attached to the ECU. (b) Fit the clip on the hole of the V5 ECU mounting bracket. (Fig. 3-1) Fig. 3-1 Issue: D 02/06/08 Page 10 of 20 pages TOYOTA RAV4 2006 - 2007 Procedure TVIP V5 RS3200PLUS V5 ECU V5 ECU Mounting Bracket (c) Apply one small foam tape to the edge of the V5 ECU as shown. (Fig. 3-2) Small Foam Tape Fig. 3-2 (d) Cut the butyl tape in half. (Fig. 3-3) Butyl Tape (Half Cut) (e) Using 3M™ Prep Sol-70 and cleaning method, clean the area indicated on the V5 ECU. (Fig. 3-3) Butyl Tape (f) Apply one and ½ piece of butyl tape to the V5 ECU as shown. (Fig. 3-3) Butyl Tape (1) Do not remove the upside of the butyl tape protective sheet. V5 ECU Fig. 3-3 (g) Using the 3MTM Prep Solvent –70, clean the V5 ECU installation area in upper of the glove box area. Equally Space V5 ECU Brace Rib 40P Hole Fig. 3-4 Clip Flat Blade Screwdriver GBS ECU Fig. 3-5 Issue: D 02/06/08 Butyl Tape V5 ECU GBS Setting (h) Connect the V5 harness' white 40P connector to the V5 ECU. (Fig. 3-4) (i) Remove the butyl tape protective sheet, then mount the V5 ECU to the hole in the metal brace in the upper of the glove box area. (Fig. 3-4) (1) Install the space between the rib and V5 ECU at equal space. (2) Press the V5 ECU to the upper of the glove box firmly. (3) After all vehicle parts re-assembly, confirm whether the glove box opens and shuts smoothly. (j) Turn the GBS adjustment screw on the GBS ECU to the "8" position. (Fig. 3-5) Page 11 of 20 pages TOYOTA RAV4 2006 - 2007 Procedure TVIP V5 RS3200PLUS (k) Insert the GBS ECU mounting bracket into the indicated bracket slot on the GBS ECU. (Fig. 3-6) GBS ECU (1) Insert the mounting bracket into the correct ECU's slot. GBS ECU Mounting Bracket CAUTION: The bracket is permanently attached once installed. Large Foam Tape Fig. 3-6 (2) Ensure the bracket is firmly attached to each ECU. (l) Attach one large foam tape to the GBS ECU as shown. (Fig. 3-6) 10mm Wrench (m) Locate and remove the screw from the air conditioner unit in the glove box area. (Fig. 3-7) Screw (1) Do not discard the screw. Fig. 3-7 (n) Using the existing screw, secure the ECU to the air conditioner unit. (Fig. 3-8) 10mm Wrench (1) Verify the screw is tightened securely. GBS ECU Screw 8P Fig. 3-8 4. Side Cutter GBS ECU V5 Harness Wire Ties (x4) 2P (White) Fig. 4-1 Issue: D 02/06/08 V5 Harness Installation (continued). (a) Secure the V5 harness' GBS wires to the vehicle harness with two wire ties. (Fig. 4-1) (b) Route the V5 harness' white 2P male connector toward the right side of the glove box area. Secure the V5 harness to the vehicle harness with two wire ties. (Fig. 4-1) Page 12 of 20 pages TOYOTA RAV4 2006 - 2007 Procedure TVIP V5 RS3200PLUS (c) Locate and remove the tape securing the vehicle harness’ white 2P connector from the right side of the glove box area. (Fig. 4-2) Tape (d) Plug in the V5 harness' white 2P connector to the vehicle harness' white 2P connector. Secure the V5 harness to the vehicle harness with one wire tie. (Fig. 4-3) 2P (White) 5. Status Monitor Installation. Fig. 4-2 (a) Remove the knockout cover in the cluster panel, first space from the right, then connect the V5 harness’ white 4P connector to the status monitor. (Fig. 5-1) Side Cutter Vehicle Harness' 2P Wire Tie (b) Insert the status monitor into the knockout opening of the cluster panel. Secure the V5 harness to the vehicle harness with one wire tie. (Fig. 5-1) RES Harness' 2P 6. Warning Label Installation. Fig. 4-3 Status Monitor Side Cutter Knockout Cover V5 Harness’ 4P (White) Wire Tie Fig. 5-1 (a) Using household Windex, clean the inside surface of the front door windows. (Fig. 6-1) (b) Place the warning label on the inside surface of the front door’s windows as shown. (Fig. 6-1) V5 Harness Warning Label Line Up With Bottom of Window Etching (1) For U.S vehicles, discard the Spanish label. For Mexico vehicles, discard the English label. 10mm (1) Use a piece of clean adhesive tape to lift the labels off their protective backing sheet. (2) Do not touch the adhesive surface of the warning labels. (c) Line up the labels properly and place on the glass once; do not use a label that was pulled off of the glass. Fig. 6-1 Issue: D 02/06/08 Page 13 of 20 pages TOYOTA RAV4 2006 - 2007 Procedure 7. Completing the Installation. Torque Wrench, 10mm Socket Negative Battery Cable TVIP V5 RS3200PLUS 90° (a) Complete the vehicle reassembly. (1) Reconnect any disconnected connectors. Battery (2) Verify the panels fit together properly with no uneven gaps between them. (b) Clean up and remove any trash. Fig. 7-1 (c) Reconnect the vehicle’s negative battery cable. (Fig. 7-1) (1) Position the negative terminal at an angle to the battery as shown. (2) Tighten the nut to 2.9 ~ 4.9 N·m (26.0 ~ 43.4 lbf·in). (3) Do not touch the positive terminal with any tool when replacing the cable. (d) Reset the power windows. (1) Turn the ignition key to “ON.” (2) Push down the power window switches of each door, and lower the windows halfway. (3) Pull the switch until the windows close. Then, further hold for a minimum of one (1) second. (e) Reset the power moon roof. (1) Push and hold moon roof switch to close side until moon roof closes. Hold for a further two (2) seconds. (f) Reset the tailgate door. (1) Push door lock control switch to the “unlock” side. (2) Pull up tailgate door handle. (g) Place the owner’s manual, and warranty card, left in their protective bags, in the glove box. Issue: D 02/06/08 Page 14 of 20 pages TOYOTA RAV4 2006 - 2007 RS3200PLUS Checklist - these points MUST be checked to ensure a quality installation. Check: TVIP V5 Look For: Accessory Function Checks Fit the appropriate fuse before beginning. Press and release the remote control’s lock 1. The turn signal lights flash once. button to start the system’s arming process. All doors lock. The security LED lights up. Wait 30 seconds. 2. After 30 seconds, the LED starts flashing; the system is now armed. Press and release the remote control’s 3. The turn signal lights flash twice. unlock button to disarm the system. The driver’s door unlocks. The LED stops flashing. Open the driver’s door, insert the key into the ignition switch and turn it to "ON". Roll down all the windows, remove the key and exit the vehicle. Arm and disarm the system with the remote 4. The doors automatically relock. again, then wait 30 seconds. The system automatically starts the arming process. Press and release the remote control’s 5. Refer to step 3. unlock button again to stop the arming process. Insert the key into the driver’s door key 6. All doors lock. cylinder and turn it toward the front of the The LED lights up. vehicle to start the arming process. Wait 30 seconds. 7. After 30 seconds, the LED starts flashing; the system is now armed. Issue: D 02/06/08 Page 15 of 20 pages TOYOTA RAV4 2006 - 2007 RS3200PLUS Checklist - these points MUST be checked to ensure a quality installation. Check: TVIP V5 Look For: Reach inside and manually unlock the 8. The driver’s door automatically relocks. driver’s door to trigger an alarm. The horn sounds repeatedly. The headlights flash repeatedly. The turn signal lights flash repeatedly. The LED lights up. Manually unlock the driver’s door again 9. The driver’s door lock attempts to lock and hold it unlocked, open the door, then sit repeatedly. in the driver’s seat. The horn continues to sound repeatedly. The headlights and turn signal lights continue flashing. The LED remains on. Press and release the remote control’s 10. The horn stops sounding. unlock button to disarm the system. All the lights stop flashing and/or turn off. The LED turns off. The turn signal lights flash twice. The driver’s door unlocks. With the door open, press the lock switch on the door to lock the doors, then close the door to start the system’s arming process. 11. All doors lock. The LED lights up. Wait 30 seconds. Reach inside and manually unlock the front 12. After 30 seconds, the LED starts flashing; the system is now armed. passenger’s door to trigger an alarm. 13. The front passenger’s door automatically relocks. The horn sounds repeatedly. The headlights flash repeatedly. The turn signal lights flash repeatedly. The LED lights up. Issue: D 02/06/08 Page 16 of 20 pages TOYOTA RAV4 2006 - 2007 RS3200PLUS Checklist - these points MUST be checked to ensure a quality installation. Check: TVIP V5 Look For: Press and release the remote control’s 14. The horn stops sounding. unlock button to stop the alarm. All the lights stop flashing. The LED turns off. Press and release the remote control’s lock 15. Refer to steps 1 and 2. button to start the system’s arming process, then wait 30 seconds until the system is armed. Unlock and open one of the rear passenger 16. Refer to step 13. doors to trigger an alarm. Repeat the above steps with the other rear 17. Refer to steps 15 and 16. passenger door and back door. Roll up all windows, remove the key and exit the vehicle. Press and release the remote control’s lock 18. Refer to step 1. button to start the arming process. Wait 30 seconds. 19. After 30 seconds, the LED starts flashing; the system is now armed. Perform the following check in a temperature-controlled environment. (50°-90° F) With the tip of key (or Striker Tool pulled 20. The horn sounds repeatedly. all the way out (PPO only)), tap the center The headlights flash repeatedly. of the driver’s door window to trigger the The turn signal lights flash repeatedly. "warn away" alarm. The LED lights up. NOTE: Adjust as necessary by increasing the GBS setting to the next level if the alarm does not trigger during functional verifications. NOTE: If you do not disarm the system, the alarm will last 20 seconds. It is not necessary to check the alarm duration. Issue: D 02/06/08 Page 17 of 20 pages TOYOTA RAV4 2006 - 2007 RS3200PLUS Checklist - these points MUST be checked to ensure a quality installation. Check: TVIP V5 Look For: Insert the key into the driver’s door key 21. The horn stops sounding. cylinder and turn it toward the back of the All the lights stop flashing and/ or turn off. vehicle to stop the alarm. The security LED turns off. Vehicle Function Checks Head Lights Functioning Head Lights High Beams Functioning High Beams Turn Signal Lights Functioning Turn Signal Lights Tail Lights Functioning Tail Lights Stop Lights Functioning Stop Lights Backup Lights Functioning Backup Lights Hazard Lights Functioning Hazard Lights Marker Lights Functioning Marker Lights Dome/Courtesy Lights Functioning Dome/Courtesy Lights Panel/Switch Illumination Functioning Controls/Illumination Accessory Controls/Illumination (if Functioning Accessory equipped) Key Sensor Buzzer Functioning Key Sensor Fog Lights (if equipped) Functioning Fog Lights Daytime Running Lights (if equipped) Functioning DR Lights Trunk/Tailgate/Bed Lights (if equipped) Functioning Lights Glove Box Light (if equipped) Functioning Glove Box Light Cruise Control Light (if equipped) Functioning Cruise Control Light Issue: D 02/06/08 Page 18 of 20 pages TOYOTA RAV4 2006 - 2007 TVIP V5 RS3200PLUS Checklist - these points MUST be checked to ensure a quality installation. Check: Look For: Seat Belt Warning Light Functioning Seatbelt Warning Light. If the warning light remains "ON", it may indicate a system malfunction. Air Bag Warning Light Functioning Air Bag Warning Light. If the warning light remains "ON", it may indicate a system malfunction. ABS Light (if equipped) Functioning ABS Light. If the warning light remains "ON,” it may indicate a system malfunction. Lamp Failure Sensor (if equipped) Functioning Lamp Failure Light. If the warning light remains “ON,” it may indicate a system malfunction. Track/Skid Control Light (if equipped) Functional Track/VSC Light. If the warning light remains “ON,” it may indicate a system malfunction. HVAC All HVAC Controls Function Power Locks (if equipped) Functioning Power Locks Power Windows (if equipped) Functioning Power Windows Power Seats (if equipped) Functioning Power Seats Power Sunroof (if equipped) Functioning Sunroof Horn Functioning Horn Gauges Functioning Gauges Front Wiper/Washer Functioning Front Wiper/Washer Rear Wiper/Washer (if equipped) Functioning Rear Wiper/Washer Clock (if equipped) Functioning Clock Issue: D 02/06/08 Page 19 of 20 pages TOYOTA RAV4 2006 - 2007 TVIP V5 RS3200PLUS Checklist - these points MUST be checked to ensure a quality installation. Check: Look For: Accessory Power Socket (if equipped) Functioning Power Socket Starter Functioning Starter Audio/Video (if equipped) Functioning Audio/Video Power Sliding Door (if equipped) Functioning Power Sliding Door Convenience Memory Settings (if Functioning Memory Settings equipped) Heated Seats (if equipped) Functioning Heated Seats Massage Seats (if equipped) Functioning Massage Seats Rear Window Defogger (if equipped) Functioning Rear Window Defogger Power Side Mirrors (if equipped) Functioning Power Side Mirrors Side Mirror Defogger (if equipped) Functioning Side Mirror Defogger Front Windshield Defogger (if equipped) Functioning Front Windshield Defogger Navigation System (if equipped) Functioning Navigation System Power Back Door (if equipped) Functioning Power Back Door Remove the appropriate fuse after checks are completed. Issue: D 02/06/08 Page 20 of 20 pages