Vauxhall - Tigra - Owners Manual - (2008)

VAUXHALL Tigra Owner’s Manual Model Year 2009.0 Edition: July 2008 TS 1622-A-09 Operation, Safety, Maintenance Data specific to your vehicle Please enter your vehicle’s data here to keep it easily accessible. You can find it in the "Service and Maintenance" and "Technical Data" sections and also on the identification plate. Fuel Designation Engine oil Grade Viscosity Tyre pressure Tyre size Summer tyres Winter tyres Weights Gross vehicle weight rating – EC kerb weight = Loading front rear Introduction Make use of the Owner’s Manual Your vehicle is an intelligent combination of forward-looking technology, impressive safety, environmental friendliness and economy. z The "In Brief" section will give you an initial overview, The retractable steel roof also gives you the opportunity to enjoy your Tigra as a coupe or a convertible. It now lies with you to drive your vehicle safely and ensure that it performs perfectly. This Owner’s Manual provides you with all the necessary information to that end. Make sure your passengers are aware of the possible risk of accident and injury which may result from improper use of the vehicle. You must always comply with the specific laws of the country that you are travelling in. These laws may differ from the information in this Owner’s Manual. When this Manual refers to a workshop visit, we recommend you use a Vauxhall Authorised Repairer. All Vauxhall Authorised Repairers provide first-class service at reasonable prices. Experienced mechanics trained by Vauxhall work according to specific Vauxhall instructions. The Owner’s Manual, Infotainment system instructions and the vehicle Service and Warranty Booklet should always be kept ready to hand in the vehicle glove compartment. z The table of contents at the beginning of the Owner’s Manual and within the individual chapters will show you where everything is. z Its index will help you find what you want. z Yellow arrows in the illustrations serve as points of reference or indicate some action to be performed. z Black arrows in the illustrations indicate a reaction or a second action to be performed. z This Owner’s Manual depicts right-hand drive vehicles. Operation is similar for left-hand drive vehicles. z The Owner’s Manual uses the internal engine codes. The corresponding sales designations are found in the chapter "Technical data". z Directional data, e.g. left or right, or front or back, in the descriptions always relate to the direction of travel. Symbols 6 Continue reading on next page. 3 The asterisk signifies equipment not fitted to all vehicles (model variants, engine options, models specific to one country, optional equipment, Vauxhall genuine parts and accessories). Page references are indicated with 3 . 3 means "see page". 9 Danger, 9 Warning, Caution 9 Danger Text marked 9 Danger provides information on risk of fatal injury. Failure to comply with the instructions could endanger life. 9 Warning Text marked 9 Warning provides information on risk of accident or injury. Failure to comply with the instructions could lead to injury. Caution Text marked Caution provides information on possible damage to the vehicle. Failure to comply with the instructions could lead to vehicle damage. Thank you for choosing a Vauxhall. We wish you many hours of pleasurable driving. Your Vauxhall Team Contents Commitment to customer satisfaction: Our aim: to keep you happy with your vehicle. All Vauxhall Authorised Repairers offer first-class service at competitive prices. Experienced, factory-trained technicians work according to factory instructions. Your Authorised Repairer can supply you with GENUINE VAUXHALLAPPROVED PARTS, which have undergone stringent quality and precision checks, and of course useful and attractive VAUXHALL-APPROVED ACCESSORIES. Our name is your guarantee! For details of the Vauxhall Authorised Repairer Network, please ring this number; 0845 090 2044 In Brief ....................................................... 2 Keys, Doors, Windows, Retractable Steel Roof ....................... 20 Seats, Interior .......................................... 44 Instruments, Controls ............................ 66 Lighting ................................................... 86 Infotainment System ............................. 90 Climate Control ..................................... 92 Driving and Operation ........................ 100 Self-help, Vehicle Care.......................... 126 Service and Maintenance ................... 152 Technical Data .................................... 168 Index ...................................................... 180 2 In Brief In Brief To unlock the driver’s door: Press button q Door locks 3 22, Key 3 20, Electronic immobiliser 3 21, Remote control 3 3 22, Central locking 3 3 23, Vauxhall alarm system 3 3 29. To unlock and open luggage compartment: Press button q on remote control twice, press button beneath the boot lid To unlock with button in driver’s door handle: With vehicle unlocked, ignition on and handbrake applied, briefly pull button R. Luggage compartment 3 26, Remote control 3 3 22. In Brief To adjust seat leg room: Pull handle, slide seat, release handle Seats 3 44, Seat position 3 45. 9 Warning Important: Do not sit nearer than 10 inches (25 cm) from the steering wheel, to permit safe airbag deployment. To adjust seat backrests: Turn handwheel 3 Seat cushion height: Pull lever Do not lean on seat backrest whilst adjusting it. Lift lever and relieve some weight from seat to raise it or press down on seat with body weight to lower it. Seats 3 44, Seat position 3 45. Seats 3 44, Seat position 3 45. 4 In Brief Head restraint height: To release, tilt head restraint forward, hold and adjust height, engage Head restraints 3 46, Head restraint position 3 47, Head restraint removal 3 47. Pull out the seat belt and click into belt buckle The seat belt must not be twisted and must lie snugly against the body. The backrest must not be tilted back too far (maximum approx. 25°). To release belt, press red button on belt buckle. Three-point seat belts 3 49, Airbag system 3 54, Seat position 3 45. Adjust exterior mirrors Select corresponding exterior mirror and adjust with the four-way switch. Mirrors 3 31, Aspherical exterior mirrors 3 31, Heated exterior mirrors 3 11, 3 32. In Brief To adjust interior mirror by swivelling Swiv el lev er on underside of mirror housing to red uce daz zle. Interior mirror 3 32. Steering wheel adju stment 3: Swivel lever down, adjust height, swivel lever up, engage Ad just steering wheel only when vehicle is stationary and steering column lock is relea sed. Airba g system 3 54, Steering colum n lock 3 13. 5 6 In Brief In Brief 1 Side air vents ............................... 3 92 2 Front passenger airbag .............. 3 54 3 Infotainment system 3 ....... 3 74,3 91 4 Hazard warning lamps ...... 3 10, 3 88 LED for Vauxhall alarm system 3 .........................................3 30 5 Information display for time, date, outside temperature, Infotainment system 3 ............... 3 74 Trip computer 3 .......................... 3 81 6 Centre air vents .............................3 92 7 Horn ...............................................3 10 Driver’s airbag ............................. 3 54 8 9 7 Turn signal lamps ................ 3 9, 3 87 Headlamp flash ................... 3 9, 3 87 Dipped beam, Main beam ........................... 3 9, 3 87 Door-to-door lighting 3 ...............3 88 Cruise control 3 ..........................3 116 16 Steering wheel adjustment 3 ....... 3 5 Remote control on steering wheel 3...........................................3 90 19 Clutch pedal 3 ........................... 3 106 10 Instruments........................... 3 66,3 72 11 Windscreen wipers ............. 3 10, 3 85 Windscreen washer system .................................. 3 11, 3 85 12 Parking lamps, dipped beam ........................ 3 9, 3 86 13 Headlamp range adjustment ......3 88 Fog tail lamp .................................3 87 Front fog lamps 3 .........................3 87 Instrument illumination ................3 89 14 Bonnet release lever ................... 3 126 15 Ignition switch with steering column lock ........... 3 13 17 Accelerator pedal .......... 3 106, 3 108 18 Brake pedal .......... 3 70, 3 106, 3 119 20 Heated seats 3 ............................ 3 46 21 Accessory socket or cigarette lighter ........................... 3 63 22 Ashtray 3 ...................................... 3 64 23 Air conditioning system 3 ........... 3 96 Heated rear window ........... 3 11, 3 34 Air recirculation system 3 ............ 3 97 24 Climate control ............................ 3 92 25 Glove compartment .................... 3 65 8 In Brief Control indicators X Seat belt 3, 3 66, 3 49. > Front fog lamps 3, 3 66, 3 87. A Engine electronics, Immobiliser 3, Easytronic 3, Fault, 3 21, 3 67, 3 104, 3 112. I Engine oil pressure, 3 68. p Alternator, 3 69. O Turn signal lamps, 3 9, 3 69, 3 87. R Brake system, clutch system, 3 70, 3 164. C Main beam, 3 9, 3 69, 3 87. u ! Preheating for diesel engines 3, 3 69. Anti-lock Braking System (ABS) 3, 3 120. S Engine oil level 3, 3 70, 3 160. Z Exhaust emission 3, 3 67, 3 112. j Easytronic 3, Start engine 3, 3 69, 3 101. EPS v Airbag systems, Belt tensioners, 3 50, 3 58. T Easytronic 3, Winter programme, 3 103. Electric Power-assisted Steering (EPS) 3, 3 70. v Electronic Stability Programme (ESP®Plus ) 3, 3 71, 3 114. Y Fuel level, 3 71, 3 111. y Seat occupancy recognition 3, 3 71, 3 59. r Fog tail lamp, 3 69, 3 87. In Brief Exterior lights Turn 7 8 9 = = = Off Parking lamps Dipped beam or main beam Headlamp flash = = = = Front fog lamps 3 Fog tail lamp Courtesy lamp Main beam, headlamp flash 3 87. Press > r 0 Headlamp flash, main beam and dipped beam Lighting 3 86, Headlamp warning buzzer 3 14, 3 84. Main beam Dipped beam = = Pull stalk towards steering wheel Push stalk forwards Push stalk forwards again Switch on turn signal lamps Right Left = = Stalk up Stalk down Turn signal lamps 3 87. 9 10 In Brief Hazard warning lamps Horn j: press right or left Windscreen wipers Operated with the ¨ button. Airbag system 3 54, Remote control on steering wheel 3 3 90. & % $ § Hazard warning lamps 3 88. = = = = Fast Slow Adjustable timed interval wipe Off Windscreen wipers 3 85, Adjustable wiper interval 3 3 85, Change windscreen wipers 3 165. In Brief Operating windscreen washer system: Pull stalk toward steering wheel Heated rear window, heated exterior mirrors The wipers will swipe for a few strokes. Climate control system 3 3 92, Heated rear window 3 34. Windscreen washer system 3 85, further information 3 165. Operated with the Ü button. 11 To clear fogged or icy windows Rotary knob for temperature and air flow clockwise, air distribution to V, Air conditioning system 3: also press button n. Climate control system 3 3 92. 12 In Brief Before starting off, check z Tyre pressure and tyre condition 3 121, 3 176. z Engine oil level and fluid levels 3 159 to 3 165. z All windows, mirrors, exterior lighting and number plates are free from dirt, snow and ice and operational. z Seats, seat belts and mirrors are correctly adjusted. 3 44, 3 49, 3 31 z Check brake function at low speed, particularly if the brakes are wet. Manual transmission Easytronic 3 Reverse: With the vehicle stationary, depress the clutch pedal, wait 3 seconds, then raise ring under gearshift lever and engage gear. N o + A/M = = = = = R = If the gear does not engage, set the lever in neutral, release the clutch pedal and depress again; then repeat gear selection. Manual transmission 3 105. Neutral/idle/start position Driving position Higher gear Lower gear Switch between Automatic and Manual mode. Reverse gear (with selector lever lock) To move the selector lever from N to R press the button on the lever. Only start in N with footbrake depressed. Easytronic 3 3 100. In Brief Steering column lock and ignition Starting the engine Turn key to position 1. Move the steering wheel slightly to release the steering column lock. Depress the clutch and brake pedals, Easytronic 3 in N, do not press accelerator, for diesel engine: turn key to 2 until control indicator ! goes out, turn key to 3; release key when engine is running. 0 1 2 = = = 3 = Ignition off Steering free, ignition off Ignition on, for diesel engine: preheating Starting Before restarting or switching off the engine, turn key back to 0. To switch on the ignition, only turn the key to 2. 13 Releasing the handbrake: Raise lever slightly, Press release button, Lower lever fully Handbrake 3 121. 14 In Brief Parking the vehicle z Always apply handbrake without pressing release button. Apply as firmly as possible on a downhill slope or uphill slope. Operate footbrake at same time to reduce operating force. z Switch off engine and ignition. To do this, turn ignition key to 0 and remove. Turn steering wheel until steering column lock perceptibly engages (anti-theft protection). On vehicles with Easytronic 3, control indicator R flashes for a few seconds after the ignition is switched off if the handbrake has not been applied. z If the vehicle is on a level surface or uphill slope, engage first gear before switching off the ignition. On an uphill slope, turn the front wheels away from the kerb. If the vehicle is on a downhill slope, engage reverse gear before switching off the ignition. Turn the front wheels towards the kerb. z Lock vehicle and arm Vauxhall alarm system 3 with button p on the remote control. To activate the anti-theft locking system 3, press button p twice. Advice when parking z Do not park the vehicle on flammable ground as combustion could occur due to the high exhaust temperatures. z Close windows and retractable steel roof. z The engine cooling fans may run after the engine has been switched off, 3 159. z After running at high engine speeds or with high engine loads, operate the engine briefly at a low load or run in neutral for approx. 30 seconds before switching off in order to protect the turbocharger 3. Remote control 3 3 22, Central locking system 3 23, Vauxhall alarm system 3 3 29, Laying the vehicle up for a long period 3 166. In Brief 15 Interesting functions Airbag system The airbag system consists of several separate systems. Front airbag system The front airbag system will be triggered in the event of a serious accident involving a frontal impact and forms safety cushions for the driver and front passenger. The forward movement of the driver and front passenger is checked and the risk of injuries to the upper body and head thereby substantially reduced. Side airbag system The side airbag is triggered in the event of a side-on collision to form a safety cushion for the driver or front passenger in the respective door area. This substantially reduces the risk of injury to the upper body and pelvis. Airbag system 3 54. 16 In Brief Operating menus in the information display 3 Selection using multifunction knob 3: rotate and press multifunction knob. Menu options are selected using menus and using the buttons/four-way button or the multifunction knob of the Infotainment system 3 or the buttons 3 on the steering wheel. The respective menu options are shown on the display. To exit a menu, turn the multifunction knob left or right to Return or Main and select. Selection using four-way button: press four-way button at top, bottom, left or right. To select with steering wheel buttons 3 Select menu options via the menus and the buttons. Information display 3 74. In Brief Ü Board Computer BC 1 BC 2 Timer 19,5° 19:36 All values 1 257.0 Ø 40 8 7.0 Ø 48.0 miles mph gal miles/gal Trip computer 3 Opening retractable steel roof Functions: z Range Only with vehicle stationary. z Instantaneous consumption z Engage the luggage compartment partition in the rear position. z Distance travelled z Average speed z Effective consumption z Average consumption z Stop watch Trip computer 3 81. z Apply handbrake z Place no objects in front of the rear window or in front of the luggage compartment partition. z Close the boot lid. z Release the locking levers on upper right and left of the window frames, pulling both levers all the way down. The retaining hook must unhook. 17 18 In Brief Closing retractable steel roof Only with vehicle stationary and boot lid closed. The luggage compartment partition must be engaged in its rear position. Do not place any objects in front of the luggage compartment partition. z Apply handbrake z Switch on ignition. z Switch on ignition. z Pull S until the roof is completely open and the boot lid is closed. An acoustic signal sounds at the beginning and end of the procedure. If the handbrake is not applied, the roof lock is not released or the luggage compartment partition is not folded back when button S is actuated, a warning buzzer sounds and the roof does not open. Retractable steel roof 3 34. z Press S until the roof and boot lid are completely closed. An acoustic signal sounds at the beginning and end of the procedure. If button S is actuated when the handbrake is not applied, a warning buzzer sounds and the roof remains open. In Brief z Move the locking levers on right and left of the window frames all the way up. Each retaining hook must engage and the roof must lock securely. Retractable steel roof 3 34. Ultrasonic parking sensors 3 When reverse gear is selected, the parking distance sensors switch on automatically. An acoustic warning sounds when the vehicle approaches an obstacle behind it. 6 Ultrasonic parking sensors 3 3 118. 19 20 Keys, Doors, Windows, Retractable Steel Roof Keys, Doors, Windows, Retractable Steel Roof Replacement keys The key number is specified in the Car Pass 3. The key is part of the electronic immobiliser. Locks 3 151. Lock cylinders Replacement keys ............................... Lock cylinders ...................................... Key with retractable key blade 3 ...... Car Pass................................................ Electronic immobiliser.......................... Remote control 3................................. Central locking system ........................ Operating central locking system with key in driver’s door lock.................... Luggage compartment....................... Vauxhall alarm system 3.................... Exterior mirrors..................................... Interior mirror ....................................... Electric windows................................... Retractable steel roof.......................... Wind deflector 3.................................. 20 20 20 20 21 22 23 25 26 29 31 32 32 34 43 Designed to free-wheel if they are forcefully rotated without the correct key or if the correct key is not fully inserted. To reset, turn cylinder with the correct key until its slot is vertical, remove key and then re-insert it. If the cylinder still free-wheels, turn the key through 180° and repeat operation. Key with retractable key blade 3 Press button to extend. Press button to retract; key section engages audibly. Car Pass The Car Pass contains safety-related vehicle data and should therefore be kept in a safe place. When the vehicle is taken to a workshop, the Car Pass data is needed in order to perform certain operations. Keys, Doors, Windows, Retractable Steel Roof 21 If control indicator A illuminates after the engine has started, there is a fault in the engine electronics or transmission electronics 3 3 67, 3 104, 3 112 or there is water in the diesel fuel filter 3 3 162. Note The immobiliser does not lock the doors. You should always lock the vehicle after leaving it and switch on the Vauxhall alarm system 3, 3 23. Electronic immobiliser The system checks whether the vehicle is allowed to start with the key used. Once the transponder in the key is recognised, the vehicle can be started. The electronic immobiliser activates automatically when the key is removed from the ignition switch. Control indicator for immobiliser A Control indicator A illuminates briefly when the ignition is switched on. If the control indicator flashes when the ignition is on, there is a fault in the system; the engine cannot be started. Switch off the ignition and then repeat the start attempt. If the control indicator A continues to flash, try to start the engine using the second key and contact a workshop for assistance. 22 Keys, Doors, Windows, Retractable Steel Roof Fault If the central locking system cannot be operated with the remote control, it may be due to the following: z Range exceeded. z Battery voltage in remote control too low, change battery. z Frequent successive activations of the remote control outside the range of the vehicle (this means that the remote control is no longer recognized). Synchronise remote control. Remote control 3 Depending on equipment level, the vehicle comes equipped with one of the remote controls depicted on this page. The remote control is integrated in the key. The remote control has a range of approx. 5 metres. This range can be affected by outside influences. Aim the remote control at the vehicle to operate. The hazard warning lamps flash to confirm remote control operation. Used to operate: z central locking system, z mechanical anti-theft locking system 3, z Vauxhall alarm system 3. Handle the remote control with care, protect it from moisture and high temperatures and avoid unnecessary operation. The windows can also be closed using the remote control. z If the central locking system is overloaded as a result of repeated operation at short intervals. The power supply is cut off for a brief period. z Interference from higher-power radio waves from other sources. Opening the vehicle 3 25. Keys, Doors, Windows, Retractable Steel Roof 23 Key with fixed key bit, see Fig. 15331 T on previous page. Have the workshop change the battery. Remote control synchronisation After changing the battery, unlock the door using the key. Insert the key in the ignition lock to synchronise the remote control. Remote control battery replacement Replace the battery as soon as the range of the remote control begins to shrink. Central locking system Batteries do not belong in household waste. They must be disposed of at an appropriate recycling collection point. To unlock Unlock driver’s door only Press button q on remote control once. Key with retractable key blade, see Fig. 15330 T on previous page. Unlock entire vehicle Press button q on remote control twice. Extend the key 3 20. Open the remote control. Replace the battery (battery type CR 20 32), noting installation position. Close the remote control and synchronise. The vehicle can also be unlocked by pulling the door handles if the anti-theft locking system is disabled. Used to unlock and lock doors, luggage compartment cover and tank flap. 24 Keys, Doors, Windows, Retractable Steel Roof To lock Close doors, luggage compartment and tank flap. Press button p on remote control. – or from the inside – Press button m in the door. The vehicle can be locked even if the driver’s door is open. Risk of being locked out. Mechanical anti-theft locking system 3 9 Warning Do not use the system if there are people in the vehicle! The doors cannot be unlocked from the inside. All doors must be closed. If the ignition was on, the driver’s door must be opened and closed once so that the vehicle can be secured. All doors are secured against opening. Keys, Doors, Windows, Retractable Steel Roof Within 10 seconds of locking, press the p button on the remote control again. Unlocking the vehicle switches off the mechanical anti-theft locking system. Note z A short time after unlocking using the remote control the doors lock again automatically if no door is opened. z To lock the doors from inside (e.g. to prevent unwanted entry from outside), press central locking switch m in the door trim. z The vehicle can be locked without the need for the key. With the driver’s door open, press central locking switch m in the door trim and then close the driver’s door. Note that unintentional actuation could cause one to be locked out. z Locked doors and luggage compartment unlock automatically in the event of an accident of a certain severity (to permit outside assistance). Prerequisite: Ignition must not be switched off. 25 Fault If the central locking cannot be operated, this can be for one of the following reasons: z If the central locking system is overloaded as a result of repeated operation at short intervals. The power supply is cut off for a brief period. z Faulty fuse in fuse box 3 140. To eliminate the cause of the fault, contact a workshop. Use the key to open and close the driver’s door. Operating central locking system with key in driver’s door lock To unlock Turn key forward in lock as far as it will go. Turn back to vertical position and remove. If the anti-theft locking system 3 is engaged, only the driver’s door will unlock. To unlock the entire vehicle: switch on the ignition, press central locking switch m and pull the driver’s door handle. To lock With doors closed, turn key towards rear of vehicle as far as it will go. Turn back to vertical position and remove. 26 Keys, Doors, Windows, Retractable Steel Roof Luggage compartment To open with the button in the driver’s door handle 1. Unlock entire vehicle 3 23. 2. Apply handbrake. 3. Switch on ignition. 4. Briefly press button R. The opening process begins after a slight delay. Pressing the button again stops the opening process. If the handbrake is not engaged when the button is pressed, a warning buzzer sounds and the luggage compartment remains closed. To open with the button beneath the boot lid 1. Unlock entire vehicle 3 23. To close: Press the button below the boot lid until the lid is completely closed. 2. Briefly press the button beneath the boot lid. The opening process begins after a slight delay. If the ignition is on but the handbrake is not applied when the button is pressed, a warning buzzer sounds and the luggage compartment closes. Pressing the button again stops the opening process. If the ignition is on but the handbrake is not applied when the button is pressed, a warning buzzer sounds and the luggage compartment remains closed. A tone sounds when the boot lid is completely closed. Locking of the lid is indicated by a single flash of the hazard warning lamps. Keys, Doors, Windows, Retractable Steel Roof Fault The boot lid can only be operated if the roof has been fully and correctly closed or opened beforehand. In the event of automatic drive malfunction or loss of battery power, the boot lid is manually opened as follows: 1. Open the door. 2. Fold down the seat backrest. The tool is fastened underneath the seat. 3. Turn the tool 90° to the right to remove. 4. Pull the front of the tool upward and out of the flooring. 27 5. Pull the tool forward out of the flooring. 28 Keys, Doors, Windows, Retractable Steel Roof 6. Open and fold down the cover of the emergency release cable. Pull the cable out slightly. 8. Have a second person hold the rear of the boot lid down. Pull the tool forward to release the lid at the rear. To close the boot lid, have a second person help you press it down and engage it in the lock. 7. Insert the tool through the eye of the emergency release cable. Support the rounded end of the tool on the cover as illustrated. The eye of the emergency release cable must lie in the groove on the tool. 9. Carefully open the boot lid by hand. Have the cause of the fault eliminated by a workshop. Refit the emergency release cable in the opening and refit the cover. Do not close the vehicle door if the cover is open. Keys, Doors, Windows, Retractable Steel Roof 29 Vauxhall alarm system 3 Monitors: z doors, luggage compartment, bonnet, z the passenger compartment, z vehicle tilt e.g. if it is raised, z the ignition. To activate All doors, windows, retractable steel roof, luggage compartment and bonnet must be closed. Press button p on the remote control. If the ignition was switched on, the driver’s door must be opened and closed once so that the anti-theft alarm system can be switched on. 2. Press button in front of the courtesy lamp (with ignition off); LED in the hazard warning lamp button flashes a maximum of 10 seconds. Activation without monitoring of passenger compartment and vehicle tilt e.g. if animals are to be left in the vehicle. 3. Close doors. 1. The luggage compartment, retractable steel roof and bonnet must be closed. 4. Activate the anti-theft alarm system. The LED in the hazard warning lamp button illuminates. After approx. 10 seconds, the anti-theft alarm system is activated without monitoring of the passenger compartment or vehicle tilt. The LED in the hazard warning lamp button flashes until the anti-theft alarm system is deactivated. Passenger compartment monitoring is deactivated if the retractable steel roof is open to prevent false alarms. 30 Keys, Doors, Windows, Retractable Steel Roof After the first 10 seconds of anti-theft alarm system activation: z LED flashes = System switched on, slowly z LED comes = Switch-off function. on for approx. 1 second On faults, contact a workshop. Light emitting diode (LED) During the first 10 seconds of anti-theft alarm system activation: To deactivate Press button q of the remote control z LED comes on = Test, switch-on delay, z LED flashes = Door, luggage quickly compartment or bonnet open, or system fault. Switch on ignition. – or – In the event of a fault in the remote control, unlock vehicle with key 3 25. If the alarm is triggered when the driver’s door is opened, deactivate the anti-theft alarm system by switching on the ignition. Keys, Doors, Windows, Retractable Steel Roof 31 Note z Changes to the vehicle interior, such as the use of seat covers, could impair the function of passenger compartment monitoring. z Switch off passenger compartment monitoring if the interior of the parked vehicle is heated. Alarm When triggered, the alarm gives off an acoustic signal (horn) and a visual signal (hazard warning lamps). The number and duration of the alarms are stipulated by legislation. The alarm can be silenced by pressing a button of the remote control or by switching on the ignition. The anti-theft alarm system is deactivated at the same time. Alarm siren with integrated battery 3 The alarm siren monitors the on-board voltage network and triggers an alarm if this network is manipulated (e.g. if the vehicle’s battery is disconnected by unauthorised persons). The alarm siren has its own power supply and is therefore not dependent on the vehicle’s battery. If the vehicle’s battery is to be disconnected (e.g. for maintenance work), the alarm siren must be deactivated as follows: switch the ignition on then off, disconnect the vehicle’s battery within 15 seconds. To switch off alarm siren: Switch ignition on then off. Exterior mirrors Adjust exterior mirrors Select corresponding exterior mirror and adjust with the four-way switch. Swinging in exterior mirror The exterior mirrors can be folded in by pressing gently on the outer edge of the housing. Aspherical exterior mirror 3 The aspherical exterior mirror reduces the blind spot. The shape of the mirror makes objects appear smaller, so allowing the estimating of the distance of vehicles following to be only partly possible. For the safety of pedestrians, the exterior mirrors will swing out of their normal mounting position if they are bumped with sufficient force. Reposition the mirror by applying slight pressure to the mirror housing. 32 Keys, Doors, Windows, Retractable Steel Roof Electric windows 9 Warning Exercise care when operating electric windows. Risk of injury, especially for children. Vehicle passengers should be informed accordingly. Keep a close watch on the windows when closing them. Ensure that nothing becomes trapped in them as they move. Ready for operation Ready for operation when the ignition is on Heated exterior mirrors 3 Heating is activated or deactivated by pressing the Ü button when the ignition is on. Interior mirror To adjust, swivel mirror housing. To reduce dazzle, swivel the lever on the underside of the mirror housing. Keys, Doors, Windows, Retractable Steel Roof 33 When a door is opened, the window of that door opens slightly. It closes automatically after the door is closed. When the retractable steel roof is opened or closed, the windows open slightly. They close automatically once the retractable steel roof is completely opened or closed. Safety function If the window glass encounters resistance above the middle of the window during automatic closing, it is immediately stopped and the window opened again. Operation To operate window in stages, briefly pull or push relevant window switch. For automatic opening or closing, pull or push switch longer; push or pull switch again to stop movement. Automatic closing is not possible during retractable steel roof operation. If the windows do not move easily because of frost, for example, repeatedly tap the switch for the window in question until the window has been closed in stages. Closing windows from outside Press button p on the remote control until the windows are fully closed. 34 Keys, Doors, Windows, Retractable Steel Roof Overload If the windows are repeatedly operated at short intervals, the power supply is briefly cut off. Fault If the windows cannot be opened and closed automatically, activate the window electronics as follows: 1. Close doors. 2. Switch on ignition. 3. Close the window completely and hold the button depressed at least 5 seconds longer. Heated rear window Heating is activated or deactivated by pressing the Ü button when the ignition is on. Climate control 3 92. 4. Open the window completely and hold the button depressed at least 1 second longer. 5. Repeat for each window. Retractable steel roof The retractable steel roof, a foldable steel top, enables the Tigra to combine the attributes of a coupe and a convertible. 9 Warning Exercise care when operating the roof. Risk of injury. Pay close attention to the roof’s movement zone during operation. Make sure that nothing could become trapped. Make sure no one is in the movement zone during roof operation. Risk of injury. Before operating the roof in garages, parking garages or the like, check the amount of vertical clearance available. Vehicle passengers should be informed accordingly. Before leaving the vehicle, remove the ignition key in order to prevent unauthorised operation of the windows and sun roof. Keys, Doors, Windows, Retractable Steel Roof Opening the roof Only with vehicle stationary. Engage the luggage compartment partition in the rear position. Apply handbrake. Place no objects in front of the rear window or in front of the luggage compartment partition. Close the boot lid 3 26. 35 Release the locking levers on upper right and left of the window frames, pulling both levers all the way down. Both retaining hooks must unhook. 36 Keys, Doors, Windows, Retractable Steel Roof Press S until the roof and boot lid are completely closed. An acoustic signal sounds at the beginning and end of the procedure. If button S is actuated when the handbrake is not applied, a warning buzzer sounds and the roof remains open. Switch on ignition. Pull S until the roof is completely open and the boot lid is closed. An acoustic signal sounds at the beginning and end of the procedure. If the handbrake is not applied, the roof lock is not released or the luggage compartment partition is not folded back when button S is actuated, a warning buzzer sounds and the roof does not open. Closing the roof Only with vehicle stationary and boot lid closed. The luggage compartment partition must be engaged in its rear position. Do not place any objects in front of the luggage compartment partition. Apply handbrake. Switch on ignition. Keys, Doors, Windows, Retractable Steel Roof Fault Automatic roof operation is only functional if the roof has been properly closed or opened beforehand. 1. Park the vehicle and apply the handbrake. z the handbrake is applied, 2. Open both windows or open the doors. z the ignition is on, 3. Switch off the ignition and remove the key. z the boot lid is completely closed, z the locking levers are unlocked. The retaining hooks engage in the corresponding recesses and the roof locks securely. Note z A warning buzzer sounds for 5 seconds after the handbrake is released and the vehicle starts off if the roof has not been properly closed or opened. Remedy this by stopping the vehicle and repeating the closing or opening procedure. z Frequent operation of the roof with the engine switched off will discharge the battery. If there is a fault in the automatic drive or loss of battery power, the fully opened roof can be manually closed as follows: Check if: z the luggage compartment partition is locked in the rear position, Push the locking levers on the right and left side of the window frame all the way up. 37 If a fault occurs while the roof is opening or closing, the roof stops in its current position. A warning buzzer sounds after 2 minutes. After an additional minute, power to the system is cut-off. The roof then moves automatically back to the luggage compartment or toward the windscreen frame. In order to close completely, open both windows, remove the key and carry out the missing steps of the following description for loss of automatic drive. 4. Open the luggage compartment. If the battery has become discharged or there is a malfunction in the boot lid, the lid must be opened manually 3 27. 9 Warning Exercise care when operating the roof. Risk of injury. Risk of pinching. Make sure that nothing could become trapped. Vehicle passengers should be informed accordingly. Closing the roof manually requires 2 persons and the use of great care. 38 Keys, Doors, Windows, Retractable Steel Roof 5. Fold down the seat backrest. The tool is fastened underneath the seat. 6. Turn the tool 90° to the right to remove. 7. Pull the front of the tool upward and out of the flooring. 8. Pull the tool forward out of the flooring. Keys, Doors, Windows, Retractable Steel Roof 9. Use the tool to forcefully pull the lock bar to unlock the cover in front of the rear window. The lock bar is on the right side of the vehicle below the cover. 10. With the lock bar pulled, have a helper pivot the cover upward by hand. The noise arising from this is normal. 39 11. Press the button below the boot lid until the lid is completely closed 3 26. If this is not possible, force the boot lid closed again as illustrated; it must completely engage in the rear lock. 40 Keys, Doors, Windows, Retractable Steel Roof 12. Release the front catches of the boot lid using the tool by inserting the tool in the guide and pressing the upper end inward; see illustration above. At the same time, pull the boot lid slightly upward out of the catch. Carry out the procedure on the right and left. 13. With two people working simultaneously on the right and left, open the boot lid rearward to its end position. Do not twist or tilt the boot lid when doing so. 9 Warning Luggage compartment does not remain in open position. 14. Release the roof retainer at the rear left of the luggage compartment partition by raising the release lever. Keys, Doors, Windows, Retractable Steel Roof 15. With the aid of a second person, carefully and slowly pull the roof upward. Grip the roof at the sides and pull forward. Make sure that the boot lid is completely open. 9 Warning Caution. Risk of pinching. 16. Pull the roof up to the windscreen frame. 41 17. Push the locking levers on the right and left side of the window frame all the way up. The retaining hooks must engage in the corresponding recess and the roof must securely lock. 42 Keys, Doors, Windows, Retractable Steel Roof 18. Have a second person help to force the boot lid closed simultaneously on the right and left. It must engage in the locks. Do not twist or tilt the boot lid. The closed lid is not locked. 19. Next, if possible open and close the boot lid once using the button below the lid. The boot lid is then locked. 20. Press down the cover in front of the rear window. It is not possible to open the roof if there is a malfunction in automatic operation. Have the cause of the fault eliminated by a workshop. Keys, Doors, Windows, Retractable Steel Roof Wind deflector 3 Install the wind deflector to reduce wind turbulence, draught and noise in the passenger compartment when the retractable steel roof is open. Insert the wind deflector in the opening in the centre of the rollover protection and fasten it with the crank. When removed, store the wind deflector in the luggage compartment. 43 44 Seats, Interior Seats, Interior Front seats ........................................... Head restraints .................................... Luggage compartment partition ....... Three-stage safety system.................. Three-point seat belts ......................... Belt tensioners...................................... Using the belts ..................................... Child restraint systems 3 .................... Airbag system...................................... Cigarette lighter 3............................... Accessory socket 3.............................. Ashtray 3 ............................................. Stowage compartments...................... Coin holder 3 ....................................... Sun visors.............................................. 44 46 47 48 49 50 52 53 54 63 63 64 64 65 65 Front seats 9 Warning Important: Do not sit nearer than 10 inches (25 cm) from the steering wheel, to permit safe airbag deployment. Never adjust seats during driving, as they can move uncontrollably. Adjust seat longitudinally Pull the handle on the front seat, slide the seat and release the handle. Adjusting the backrest Turn side handwheel on the seat while releasing the pressure on the backrest. Seats, Interior Adjusting the seat height Lift lever and relieve some weight from seat to raise it or press down on seat with body weight to lower it. Fold backrest forward To fold the backrest forwards, e.g. to reach the storage compartment behind the seats, lift release lever. 45 Seat position 9 Warning Only drive with the seat correctly adjusted. z Sit with your buttocks as far back against the backrest as possible. Adjust the distance between your feet and the pedals so that your legs are slightly angled when pressing the pedals. Slide the passenger seat as far back as possible. 46 Seats, Interior z Sit with your shoulders as far back against the backrest as possible. Set the backrest rake so that you can easily reach the steering wheel with your arms slightly bent. Maintain contact between your shoulders and the backrest when turning the steering wheel. Do not angle the backrest too far back. We recommend a maximum rake of approx. 25°. z Adjust the steering wheel 3 5. z Set seat height 3 high enough to have a clear field of vision on all sides and of all display instruments. There should be at least six inches of clearance between your head and the headlining. Your thighs should rest lightly on the seat without pressing into it. z Adjust the head restraint. Heated seats 3 Two pushbuttons ß in the centre console. For heating with ignition on, press button ß. Head restraints Adjustment Tilt head restraints forwards, hold and adjust height. Allow head restraints to engage after adjustment. Seats, Interior Head restraint position 9 Warning Only drive with the head restraint set to the proper position. The middle of the head restraint should be at eye level. If this is not possible for extremely tall persons, set to highest position, and set to lowest position for small persons. Removing Press and release the two catches. Pull and remove the head restraint. Stow head restraints securely in luggage compartment. Do not drive with head restraints removed if the seat is occupied. Note Only approved objects or components should be attached to the head restraint of the unoccupied front passenger seat. 47 Luggage compartment partition When the retractable steel roof is closed, the partition can be folded forward to enlarge the luggage compartment: pull both catches inward and fold the partition forward until it engages. 48 Seats, Interior Three-stage safety system Comprising: z three-point seat belts, z belt tensioners at the seats, z airbag systems for driver and front passenger. The three stages are activated in sequence depending on the severity of the accident: z The automatic seat belt locking devices prevent the belt strap from being pulled out and thus ensure that the vehicle occupants are retained in their seats. If the retractable steel roof is to be opened, pull the centre of the partition, release it and fold it rearward until it engages. Place no objects in front of the luggage compartment partition. z The seat belts are pulled down at the belt buckles. This means the belts fit snugly, the occupants are decelerated early with the vehicle and the body loading is reduced. z The airbag systems are also triggered in the event of severe accidents and form a safety cushion for the occupants. 9 Warning The airbag systems serve to supplement the three-point seat belts and belt tensioners. The seat belts must therefore always be worn. Disregard of these instructions may lead to injuries or endanger life. Vehicle passengers should be informed accordingly. Always follow the instructions provided with the child restraint system! Seats, Interior 9 Warning Fasten your seat belt before each trip. In the event of an accident, persons not wearing seat belts endanger their fellow occupants and themselves. Seat belt control indicator X 3 3 66. Seat belts are designed to be used by only one person at a time. They are not suitable for anyone under 12 years of age or under 150 cm tall. Three-point seat belts The seat belts have an automatic retractor, so that the belt is spring tensioned and always lies against the body. Information on correct seat position 3 45. The seat belts are locked during heavy acceleration or deceleration of the vehicle. This prevents the belt from extending, keeping the occupant in their seat. For children up to 12 years of age, we recommend the Vauxhall child restraint system 3 53. 49 Testing the seat belts Check all parts of the belt system periodically for damage and function. Replace damaged components. After an accident, have the seat belts and triggered belt tensioners replaced by a workshop. Make sure that seat belts are not damaged or trapped by sharp-edged objects. 50 Seats, Interior Belt tensioners The seat belts are pulled down at the buckles on a front or rear impact above a certain severity. This tightens the belts. Actuation of belt tensioners Indicated by continuous illumination of control indicator v. Triggered belt tensioners must be replaced by a workshop. Belt tensioners can only be triggered once. Control indicator v for belt tensioners The function of the belt tensioners and airbag systems is monitored electronically and indicated by the control indicator v. When the ignition is switched on, the control indicator illuminates for approx. 4 seconds. If it does not illuminate, or if it does not go out after 4 seconds, or if it illuminates whilst driving, there is a fault in the belt tensioner or airbag systems 3 58. The systems might not trigger in the event of an accident. Deployment of the belt tensioners is indicated by continuous illumination of v. Seats, Interior 9 Warning Have the cause of the fault eliminated by a workshop immediately. Self-diagnosis integrated into the system allows rapid fault identification. Important z Do not affix or place accessories or other objects within the deployment zone of the belt tensioners. Do not make any modifications to belt tensioner components as this will invalidate the vehicle type approval. 9 Warning Incorrect handling (e.g. removal or fitting of seat belts or belt buckles) can trigger the belt tensioners with risk of injury. 51 z The belt tensioner and airbag system control electronics can be found in the centre console area. In order to avoid malfunctions, do not store magnetic objects in this area. z We recommend that you have the front seats removed by a workshop in the event of triggering of the airbags and belt tensioners. z The belt tensioners trigger once only, indicated by the continuous illumination of the control indicator v. Have a workshop replace triggered belt tensioners. z When disposing of the vehicle, the safety instructions given for this must be observed. Take the vehicle to a recycling company for disposal. 52 Seats, Interior Using the belts Fitting seat belts The seat belt must not be twisted and must lie snugly against the body. The backrest must not be tilted back too far (maximum approx. 25°). Pull the belt out of the reel, guide it across the body (making certain it is not twisted) and engage the latch plate in the buckle. Tension the lap belt frequently whilst driving by tugging the shoulder belt. 9 Warning On pregnant women in particular, the lap belt must be positioned as low as possible across the pelvis so as not to put too much pressure on the abdomen. Loose or bulky clothing prevents the belt from fitting snugly. Do not place objects such as handbags or mobile phones between the belt and your body. 9 Warning The belt must not rest against hard or fragile objects in the pockets of your clothing. Removing the belt To release seat belt, press red button on belt buckle. Seats, Interior Child restraint systems 3 Follow the usage instructions for the child restraint system. Always comply with local or national regulations. In some countries, the use of child restraint systems is forbidden on certain seats. Selecting the right system Your child should travel facing backwards in the vehicle for as long as possible. A child has a very weak cervical spinal column and in the event of an accident is less likely to suffer injury in a rearward-facing, semilying position than if seated upright. 9 Warning Never carry child restraint systems on your lap, risk of fatal injury. Permissible options for fitting a child safety seat Weight and age class1) On the front passenger seat B1 = Limited, only with seat occupancy recognition system and Vauxhall child restraint system with transponders 3. Move seat height 3 to highest position. Move front passenger seat back as far as possible. Group 0: up to 10 kg or approx. 10 months Group 0+: up to 13 kg or approx. 2 years B1 Group I: 9 to18 kg or approx. 8 months to 4 years B1 Group II: 15 to 25 kg or approx. 3 to 7 years Group III: 22 to 36 kg or approx. 6 to 12 years 53 B 1 Note z Children under 12 years or under 150 cm tall should only travel in an appropriate child safety seat. z When transporting children, use the child restraint systems suitable for the child’s weight. z Check that the child restraint systems have been correctly installed – see instructions provided with child restraint system. z The covers of Vauxhall child restraint systems can be wiped clean. z Do not stick anything on the child restraint systems and do not cover them with any other materials. z A child restraint system which has been subjected to stress in an accident must be replaced. z Secure or remove child restraint systems carried in the vehicle when not in use. 1) We recommend the use of each system until the child reaches the upper weight limit. 54 Seats, Interior Exception: Passenger seat with seat occupancy recognition system 3. The seat occupancy recognition system deactivates the front and side airbags for the front passenger seat if the seat is unoccupied or a Vauxhall child restraint system with transponders 3 has been fitted to the front passenger seat. Seat occupancy recognition – 3 58. Vauxhall child restraint system with transponders 3 3 59. Examples of events triggering the front airbag system: Airbag system z seat occupancy recognition 3, Front airbag The front airbag system consists of one airbag in the steering wheel and one in the instrument panel. These can be identified by the word AIRBAG. z the control indicator for Vauxhall child restraint systems y with transponders 3 in the courtesy lamp. The front airbag system comprises: z an airbag with inflator in the steering wheel and a second one behind a trim panel above the glove compartment, z the control electronics with impact sensors, z control indicator for airbag systems v in the instrument cluster, The front airbag system will be triggered: z depending on the severity of the accident, z depending on the type of impact, z within the range shown in the illustration, z independently of the side airbag system. The ignition must be on. z Impact against a non-yielding obstacle: the front airbags are triggered at low vehicle speed. z Impact against a yielding obstacle (such as another vehicle): The front airbags are only triggered at a higher vehicle speed. Seats, Interior When triggered, the front airbags inflate in milliseconds and form a safety cushion for driver and front passenger. Forward movement is checked and the risk of injuries to the upper body and head thereby substantially reduced. No impairment of view will occur, because the airbags inflate and deflate so quickly. 9 Warning Optimum protection is only provided with the seat in the proper position 3 45. Keep the area in which the airbag inflates clear of obstructions. Wear the three-point seat belt properly fastened. The front airbag system is an additional safety device, not a replacement for your seat belt. 55 The front airbag system will not be triggered in the event of: z the ignition being switched off, z minor frontal collisions, z accidents in which the vehicle overturns, z collisions involving a side or rear impact, that is to say, if it would not be of benefit to the occupants. 56 Seats, Interior In addition, the front airbag system will not be triggered for the front passenger in versions with seat occupancy recognition 3 if: z the front passenger seat is unoccupied, z there is a properly mounted Vauxhall child restraint system with transponders 3 . Seat occupancy recognition system 3 58. Vauxhall child restraint system with transponders 3 3 59. Side airbags The side airbag system consists of an airbag in each front seat backrest. This can be identified by the word AIRBAG. The side airbag system comprises: z an airbag with inflator in the back of the driver’s and front passenger seat respectively, z the control electronics, z the side impact sensors, z control indicator for airbag systems v in the instrument cluster, z seat occupancy recognition 3, z the control indicator for Vauxhall child restraint systems y with transponders 3 in the courtesy lamp. The side airbag system will be triggered: z depending on the severity of the accident, z depending on the type of impact, z within the range shown in the illustration on the driver’s or front passenger side, z independently of the front airbag system. The ignition must be on. Seats, Interior Exception: Passenger seat with seat occupancy recognition system 3. The seat occupancy recognition system deactivates the front and side airbags on the front passenger seat if the seat is unoccupied or a Vauxhall child restraint system with transponders 3 has been fitted to the front passenger seat. Seat occupancy recognition – 3 58. Vauxhall child restraint system with transponders 3 3 59. 57 9 Warning Keep the area in which the airbag inflates clear of obstructions. The side airbags will not be triggered in the event of: z the ignition being switched off, z frontal collisions, z accidents in which the vehicle overturns, z collisions involving a rear impact, When deployed, the side airbag inflates within milliseconds and forms a safety cushion for the driver or front passenger in the respective front door area. This substantially reduces the risk of injury to the upper body and pelvis in the event of a side-on collision. z collisions involving a side impact outside the passenger cell. In addition, the side airbag system will not be triggered for the front passenger in versions with seat occupancy recognition 3 if: z the front passenger seat is unoccupied, z there is a properly mounted Vauxhall child restraint system with transponders 3 . Seat occupancy recognition 3 58. Vauxhall child restraint system with transponders 3 3 59. 58 Seats, Interior 9 Warning Have the cause of the fault eliminated by a workshop immediately. Self-diagnosis integrated into the system allows rapid fault identification. Control indicator v for airbag systems The function of the airbag systems is monitored electronically together with the seat occupancy recognition 3 and the belt tensioners, and indicated by the control indicator v . When the ignition is switched on, the control indicator illuminates for approx. 4 seconds. If it does not illuminate, does not go out after 4 seconds or illuminates whilst driving, there is a fault in the airbag systems, seat occupancy recognition 3 or in belt tensioners 3 50. The systems may fail to trigger in the event of an accident. Deployment of the airbags is indicated by continuous illumination of v. Seat occupancy recognition 3 The seat occupancy recognition system deactivates the passenger front and side airbags if the front passenger seat is unoccupied or a Vauxhall child restraint system with transponders 3 has been fitted to the front passenger seat. Control indicator y for seat occupancy recognition is located in the courtesy lamp. If control indicator y illuminates for approx. 4 seconds when the ignition is switched on, the vehicle is equipped with seat occupancy recognition 3 58, Fig. 12097 S. If a Vauxhall child restraint system with transponders 3 is fitted, the control indicator y illuminates permanently after the ignition is switched on as soon as the system has detected the child restraint system. Only then may the child restraint system with transponders 3 be used on the passenger seat. Seats, Interior 59 9 Warning Only Vauxhall child restraint systems with transponders 3 should be fitted on the front passenger seats. Use of systems without transponders poses a risk of fatal injury. Vauxhall child restraint systems with transponders 3 can be identified by a sticker or badge. Vehicles with seat occupancy recognition can also be identified from the sticker on the passenger seat. Vauxhall child restraint systems with transponders 3 are automatically detected if correctly fitted to the front passenger seat. The front and side airbag systems for the front passenger seat are deactivated when these child restraint systems are used. It is essential to observe the seat occupancy recognition 3 control indicator 3 58. Control indicator y for Vauxhall child restraint systems with transponders 3 The presence of a Vauxhall child restraint system with transponders 3 is indicated after the ignition has been switched on by continuous illumination of the control indicator y in the courtesy lamp, as soon as the seat occupancy recognition system has detected the child restraint system. If the control indicator does not illuminate during driving, the front and side airbags for the front seat passenger are not deactivated and there is a risk of fatal injury to the child. Have a workshop eliminate the cause of the fault. If the child restraint system is not correctly installed or the transponders are defective, the turn signal lamp will flash. Check for correct child restraint system installation. For installation of child restraint system with transponders 3 – see instructions provided with child restraint system. 60 Seats, Interior If the control indicator flashes when the child restraint system with transponders 3 is correctly fitted, there is a fault and a danger to the child. Have the cause of the fault eliminated by a workshop. Important z Owing to the risk of injury when the airbags deploy, accessories and objects must not be placed within the expansion range of the airbag systems. z Use only a dry cloth or interior cleaner to clean the steering wheel, instrument panel, seat backrests and seat cushion of the front passenger seat. Do not use any aggressive cleaning agents. If no Vauxhall child restraint system with transponders 3 is fitted, the control indicator must not illuminate or flash as the passenger airbag systems would not deploy. Have the cause of the fault eliminated by a workshop. z Do not place any objects between the airbag systems and the vehicle occupants; danger of injury. z Only protective covers which are approved for your vehicle with side airbag may be fitted on the seats. When fitting the protective covers, make sure that the airbag units on the outboard sides of the seat backrests are not covered. 9 Warning If the Vauxhall child restraint system with transponders 3 has been fitted according to the instructions, the control indicator for Vauxhall restraint systems with transponders must illuminate in the courtesy lamp when the ignition is switched on. If the control indicator does not illuminate during driving, the front passenger airbag systems are not deactivated and there is a risk of fatal injury. Have a workshop eliminate the cause of the fault. 9 Warning Never carry child restraint systems or other objects on your lap - risk of fatal injury. z The airbag systems and belt tensioner control electronics can be found in the centre console area. In order to avoid malfunctions, do not store magnetic objects in this area. z Do not stick anything on the steering wheel, instrument panel, seat backrests or roof frame in the vicinity of the airbags, or on the front passenger’s seat cushion, or cover any of those areas with other materials. z The airbag systems are triggered independently of one another depending on the severity of the accident and type of impact. z Each airbag deploys once only. Have a workshop replace deployed airbags immediately. z The speeds, directions of movement and deformation properties of the vehicles, and the properties of the obstacle concerned, determine the severity of the accident and triggering of the airbags. The degree of damage to your vehicle and the resulting repair costs alone are not indicative that the criteria for triggering of the airbags were met. Seats, Interior z Do not perform any alterations on the components of the airbag system, as this would render the vehicle unroadworthy. 9 Warning If handled improperly the airbag systems can be triggered in an explosive manner – risk of injury! z We recommend entrusting removal of the steering wheel, the instrument panel, all panelling parts and the seats to a workshop in the event of triggering of the airbags and belt tensioners. z When disposing of the vehicle, the safety instructions given for this must be observed. Take the vehicle to a recycling company for disposal. z In vehicles with seat occupancy recognition 3 persons weighing less than 35 kg must not be transported. This does not apply to children that are being transported in child restraint systems with transponders 3. z In vehicles with seat occupancy recognition 3, do not place any heavy objects on the front passenger seat otherwise the airbag systems for the front passenger seat may be triggered in the event of an accident. z In vehicles with seat occupancy recognition 3, to prevent malfunctions do not use protective covers or seat cushions on the front passenger seat. 61 z When using a Vauxhall child restraint system with transponders 3 on the front passenger seat, in order to prevent malfunctions, no objects (e.g. plastic sheet, stickers or heated mats) may be placed under the child restraint system. 9 Warning Passengers must never carry child restraint systems and other objects on their laps. If carried in this way, child restraint systems with transponders 3 in vehicles with seat occupancy recognition 3 could prevent the front passenger airbag systems from being triggered in the event of an accident. 62 Seats, Interior Vehicles with seat occupancy recognition can be identified by control indicator y in the courtesy lamp. If control indicator y illuminates for approx. 4 seconds when the ignition is switched on, the vehicle is equipped with seat occupancy recognition 3 58. Seat occupancy recognition in a vehicle is also indicated by a sticker on the front passenger seat – see page Fig. 12106 A. Use of child restraint systems 3 on the front passenger seat of vehicles without seat occupancy recognition 3 9 Warning No child restraint system 3 may be installed on front passenger seat. Danger to life. Seat occupancy recognition 3 3 58. Use of a child restraint system 3 on the front passenger seat of a vehicle with seat occupancy recognition 3 9 Warning Only Vauxhall child restraint systems with transponders 3 can be fitted on the front passenger seats. Use of systems without transponders poses a risk of fatal injury. The seat occupancy recognition system detects Vauxhall child restraint systems with transponders 3 and deactivates the front and side airbags for the front passenger seat. Seat occupancy recognition 3 58. Vauxhall child restraint systems with transponders 3 can be identified by a sticker or badge. Seats, Interior 63 Do not exceed the maximum power consumption of 120 watts. Electrical accessories connected to the socket must comply with the electromagnetic compatibility requirements laid down in DIN VDE 40 839, otherwise vehicle malfunctions may occur. Do not connect any current-delivering accessories, e.g. electrical charging devices or batteries. Cigarette lighter 3 Accessory socket 3 The cigarette lighter is in the centre console. The accessory socket is in the centre console. Press in cigarette lighter with ignition switched on. Switches off automatically when element is glowing. Withdraw cigarette lighter. The accessory socket is ready for use when the ignition is switched on. Use of the socket while the engine is not running will drain the battery. Caution Do not damage the sockets by using unsuitable plugs. 64 Seats, Interior Ashtray 3 Caution To be used only for ash and not for combustible rubbish. Open the ashtray cover to the resistance point. To empty, open the ashtray cover fully beyond its resistance point, causing the insert to lift. Grip both sides of the ashtray insert and pull upwards. To enlarge the storage compartment remove the ashtray completely. Stowage compartments Stowage compartment behind the seats The compartment is only suitable for stowing light objects. Maximum load: 10 kg. 9 Warning Secure objects to prevent them from falling out and causing injury while driving. The load must not hinder pedal, handbrake or gearshift operation or impair the driver in any way. Seats, Interior 65 Sun visors Use the sun visor to protect from glare by pulling it down and swivelling it to the side. Glove compartment To open, pull handle upwards. Can be locked with the vehicle key. On the inside of the glove compartment cover there is a pen holder. The glove compartment should be closed while the vehicle is in motion. Coin holder 3 In the centre console. 66 Instruments, Controls Instruments, Controls Control indicators ................................ Instrument display ............................... Information display ............................. Warning buzzers.................................. Windscreen wipers............................... 66 72 74 84 85 Control indicators The control indicators described here are not present in all vehicles. The descriptions however, apply to all instrument versions. The control indicator colours mean: z z z z Red Yellow Green Blue Danger, important reminder, Warning, note, fault On confirmation, On confirmation, X Seat belt 3 Control indicator illuminates red. Illuminates after turning on the ignition (with warning tone) until the seat belt is applied. Fasten seat belt 3 52. > Front fog lamps 3 Control indicator illuminates green. Illuminates when the front fog lamps are on 3 87. Instruments, Controls 67 Z Exhaust emission Control indicator illuminates or flashes yellow. It illuminates when the ignition is switched on and goes out shortly after the engine starts. Illuminated when the engine is running Fault in emission control system. The permitted emissions may be exceeded. Contact a workshop immediately. A Engine electronics, transmission electronics, immobiliser, diesel fuel filter 3 Control indicator illuminates or flashes yellow. It illuminates for a few seconds when the ignition is switched on. Illuminated when the engine is running Fault in engine or transmission electronic system. Electronics have switched to the emergency running programme. Fuel consumption may be increased and the vehicle’s driveability reduced, see page 3 112. If the fault cannot be eliminated by restarting, contact a workshop immediately. For vehicles with diesel engine, the diesel fuel filter may need to be drained of water 3 162. If it flashes when the ignition is on Fault in the electronic immobiliser system; the engine cannot be started 3 21. If it flashes when the engine is running: Fault that could lead to catalytic converter damage. Ease up on the accelerator pedal until the flashing stops 3 112. Seek the immediate assistance of a workshop. 68 Instruments, Controls 1. Move out of the flow of traffic as quickly as possible without impeding other vehicles. 2. Depress clutch. 3. Move gearshift lever to neutral, or with Easytronic 3 place selector lever in N. 4. Switch off ignition. 9 Warning v Airbag systems 3, Belt tensioners Control indicator illuminates red. I Engine oil pressure Control indicator illuminates red. Illuminated when the engine is running Fault in the airbag or belt tensioner systems 3 50, 3 58. Illuminates when the ignition is switched on and goes out shortly after the engine starts. Illuminated when the engine is running Caution Engine lubrication may be interrupted. This may result in damage to the engine and/or locking of the drive wheels. When the engine is off, considerably more force is needed to brake and steer. Do not remove key until vehicle has come to a standstill, otherwise the steering column lock could engage unexpectedly. Check engine oil level before contacting a workshop. Instruments, Controls 69 ! Preheating for diesel engines 3 Control indicator illuminates yellow. Preheating activated. Only activates when outside temperatures are low. T Winter programme of Easytronic 3 Control indicator illuminates yellow. Control indicator is illuminated when Winter programme is enabled 3 103. r O Turn signal lamps Control indicator flashes green. The control indicator flashes if a turn signal or the hazard warning lamps are activated. Rapid flashing: failure of a turn signal lamp or associated fuse. Replacing bulbs 3 144. Fuses 3 140. C Fog tail lamp Control indicator illuminates yellow. Main beam Control indicator illuminates blue. Illuminates when the fog tail lamp is on 3 87. Illuminated when main beam is on and during headlamp flash 3 9, 3 87. p Alternator Control indicator illuminates red. j Easytronic 3, Start engine Control indicator illuminates yellow. The engine can only be started if the footbrake is depressed. If the footbrake is not depressed, the control indicator illuminates 3 101. Illuminates when the ignition is switched on and goes out shortly after the engine starts. Illuminated when the engine is running Stop, switch off engine. Battery is not charging. Contact a workshop immediately. 70 Instruments, Controls S Engine oil level 3 Control indicator illuminates yellow. The engine oil level is checked automatically. Illuminated when the engine is running Engine oil level too low. Check engine oil level and top up engine oil if necessary 3 160. EPS1) Electric Power-assisted Steering (EPS) Control indicator illuminates yellow. R Brake system, clutch system Control indicator illuminates or flashes red. Illuminated Illuminates when the ignition is switched on if the handbrake is applied 3 119. Illuminates when the handbrake is released if the fluid level for the brake or clutch system is too low 3 164. 9 Warning Flashes On vehicles with Easytronic 3 , control indicator R flashes for a few seconds after the ignition is switched off if the handbrake has not been applied. Fault in EPS. Vehicle can still be driven, but greater force is required for steering. Contact a workshop immediately. u Anti-lock Braking System (ABS) 3 Control indicator illuminates red. Illuminated while driving Fault in ABS 3 120. Stop. Do not continue your journey. Consult a workshop. 1) EPS = Electric Power-assisted Steering. Instruments, Controls v Electronic Stability Programme (ESP®Plus) 3 Control indicator flashes or illuminates yellow. Flashing during driving System engages 3 114. Illuminated while driving Fault in system 3 114. Y Fuel level Control indicator illuminates or flashes yellow. Illuminated Fuel level in fuel tank is too low. Refuel. Flashing Fuel supply exhausted, refuel immediately. Never let the tank run dry! Erratic fuel supply can cause catalytic converter to overheat 3 112. Diesel engines: Bleed fuel system after running empty 3 126. y Seat occupancy recognition 3 3 58, 3 59. 71 72 Instruments, Controls Instrument display Tachometer Displays the engine rpm. Drive in a low engine speed range for each gear as much as possible. Caution If the pointer is in the warning zone, the maximum permitted engine speed is exceeded. Engine at risk. Speedometer Speed display. Mileage display If the ignition is off, the mileage is displayed for approx. 15 seconds by briefly pressing the reset knob. Top line: Trip odometer Display of miles covered since reset. To reset, hold the reset knob depressed for a few seconds with the ignition on. Bottom line: Odometer Records the miles counted. Service and maintenance 3 152. Coolant temperature display Coolant temperature display. Pointer in zone at left = Pointer between = the zones Pointer in red = zone Engine operating temperature not yet reached Normal operating temperature Temperature too high: Stop vehicle and switch off engine. Danger to engine. Check coolant level 3 163. For physical reasons, the engine temperature gauge shows the coolant temperature only if the coolant level is adequate. During operation the system is pressurised. The temperature may therefore rise briefly to over 100 °C. Instruments, Controls Fuel gauge Display of fuel level in tank When fuel level is low, control indicator Y illuminates. If the if control indicator flashes, refuel immediately. Never run the tank dry! Because of the fuel remaining in the tank, the amount of fuel required to fill the tank may be less than the specified tank capacity. Transmission display 3 Display of current gear or mode with Easytronic 3: R N A 1-5 Reverse gear. Neutral. Automatic mode on Easytronic. Manual mode, current gear on Easytronic. Easytronic 3 3 100. 73 Service display 3 When the indicator InSp in the odometer display illuminates, make a service appointment with a workshop as soon as possible. Service and maintenance 3 158. 74 Instruments, Controls Some information appears in the display in an abbreviated form. Ü Board Computer BC 1 12:01 17 ,0°C FM 3 90,6 MHz REG AS RDS BC 2 Timer 1 257.0 Ø 40 8 7.0 Ø 48.0 TP Information display Triple information display 3 Display of time, outside temperature and date/Infotainment system (when it is on). When the ignition is off, the time, date and outside temperature can be displayed by briefly pressing one of the two buttons adjacent to the display. 19,5° 19:36 All values miles mph gal miles/gal Graphical Information Display 3 Display of time, outside temperature and date/Infotainment system (when it is on). The type of information and how it is displayed depend on the equipment of the vehicle and the settings made. Instruments, Controls 75 9 Warning 8:56 -5 ,5°C 07.04.2008 Caution: The road surface may already be icy even though the display indicates a few degrees above 0 °C. : Slippery road -2,5°C OK Outside temperature A fall in temperature is indicated immediately and a rise in temperature after a time delay. If the external temperature falls to 3 °C, to warn of ice on the road the symbol : appears in the triple information display. When the temperature climbs, the symbol : goes out above 5 °C. In vehicles with graphical information display 3, the warning message Slippery road is shown in the display as a warning for icy road surfaces. No message is displayed at temperatures below -5 °C. 76 Instruments, Controls Automatic time synchronisation 3 The RDS signal of most VHF transmitters automatically sets the time. This can be identified by } in the display. 8:56 5 ,5°C 07.04.2008 Triple information display Set date and time The Infotainment system 3 must be off. Activate setting mode by holding the Ö button depressed for approx. 2 seconds. The flashing value is adjusted using the ; button. The Ö button is used to switch to the next unit and to exit setting mode. Some transmitters do not send a correct time signal. In such cases, we recommend that you switch off automatic time synchronisation. Activate setting mode and set it to year setting. Hold the Ö button depressed approx. 3 seconds until } flashes in the display and “RDS TIME" appears. The function is activated (RDS TIME 1) or deactivated (RDS TIME 0) with the ; button. Exit setting mode using the Ö button. FM [TP] ��� 19,5° CDin 90.6 MHz 19:36 Graphical information display 3, Selecting functions The graphical information display depicts functions and their menus. These functions are marked or executed in the menu display via the four-way switch, the multifunction knob 3 on the Infotainment System or buttons 3 on the steering wheel. Instruments, Controls To select with four-way button Select menu items via menus and with the buttons/four-way button of the Infotainment system. Selection with the multifunction knob 3 Turn the multifunction knob to highlight menu items or commands and to select function areas. Press the multifunction knob to select the highlighted item or confirm a command. To exit a menu, turn the multifunction knob left or right to Return or Main and select. 77 Selection using buttons 3 on steering wheel Select menu options via menus and with the buttons. 78 Instruments, Controls 7 FM [TP] CDin Settings Time, Date 19,5° 19:36 7 Time, Date 19,5° 19:36 19:36 Time 19:36 10 . 07 . 2008 Date 10 . 07 . 2008 Language ��� 90.6 MHz Units Contrast Day / Night 19,5° 19:36 6 Synchron. clock automatical. 6 Ign. logic Function areas For each functional area there is a main page (Main), which is selected at the top edge of the display (not with the Infotainment System CD 30 without the hands-free mobile phone system): System settings The settings are accessed via the Settings menu. Setting the date and time 3 Select menu item Time, Date, from the Settings menu. The menu for Time, Date is displayed. z z z z Press the Main button 3 (not found on all Infotainment systems) on the Infotainment system (call up main display). Press the Settings button on the Infotainment system. For Infotainment System CD 30, no menu may be selected. Audio, Navigation 3, Telephone 3, Trip computer 3. Function areas audio, navigation 3 and telephone 3 – see Infotainment system instructions. The Settings menu is displayed. Select the required menu item and make setting. Instruments, Controls Automatic time synchronisation 3 The RDS signal of most VHF transmitters automatically sets the time. Some transmitters do not send a correct time signal. In such cases, we recommend that you switch off automatic time synchronisation. On Infotainment systems with navigation 3, time and date are also harmonised upon receipt of a GPS satellite signal. The function is activated by ticking the field in front of Synchron. clock automatical. in the Time, Date menu. 7 Settings 19,5° 19:36 7 13 Languages 79 19,5° 19:36 X English Time, Date Language English Deutsch Units Deutsch Español Contrast Español Nederlands Day / Night Nederlands Français 6 Ign. logic Français Italiano Language selection You can select the display language for some functions. Select the required language. Select menu item Language from the Settings menu. In systems with voice output 3, when the language setting of the display is changed the system will ask whether the announcement language should also be changed – see Infotainment system instructions. The available languages are displayed. Selections are indicated by a 6 in front of the menu item. 80 Instruments, Controls 7 Settings 19,5° 19:36 7 Contrast 19,5° 19:36 Select menu item Day / Night from the Settings menu. Time, Date Language ~ Europe-SI Units | | | Japan Contrast Day / Night Setting display mode 3 Display brightness is independent of vehicle lighting. Settings are made as follows: 12 Great Britain USA The options are displayed. Automatic: adapted based on vehicle lighting. Always day design: Black text on light background. 6 Ign. logic Always night design: White text on dark background. Setting units of measure Select menu item Units from the Settings menu. Adjust contrast Select menu item Contrast from the Settings menu. The available units are displayed. The menu for Contrast is displayed. Select the required unit. Confirm the required setting. Selections are indicated by a o in front of the menu item. Selections are indicated by a o in front of the menu item. Ignition logic 3 Adjustment, see Infotainment system instructions. Instruments, Controls Ü Board Computer BC 1 19,5° 19:36 All values BC 2 Timer 81 1 8 257.0 Ø 40 7.0 Ø 48.0 Range miles mph Aver. Consump. Inst. Consumpt. 199 miles 48.0 miles/gal 46.0 miles/gal Range 23miles gal miles/gal Graphical information display 3, Trip computer 3 The trip computers provide information on driving data, which is continually recorded and evaluated electronically. The on-board computer main page gives information on range, momentary consumption and average consumption 3. To display the other trip computer driving information, press BC button on Infotainment system 3 or select trip computer menu on display. For vehicles with Infotainment System CD 30 3 and steering wheel remote control 3 , the left steering wheel buttons only operate the trip computer. 19,5° 19:36 Range Range is calculated from current fuel tank content and instantaneous consumption. The display shows average values. After refuelling, the vehicle updates the range automatically after a brief delay. OK If the fuel in the tank will allow less than 30 miles (50 km) of travel, the message Range appears in the display. If the fuel in the tank will allow less than 20 miles (30 km) of travel, the message Please refuel! 3 appears in the display. Acknowledge warning message 3 76. 82 Instruments, Controls Instantaneous consumption Display of current consumption. At low speeds, consumption per hour is displayed. Distance travelled Display of distance travelled. The measurement can be reset at any time. Effective consumption Display of fuel consumed. The measurement can be reset at any time. Average speed Display of average speed. The measurement can be reset at any time. Average consumption Display of average consumption. The measurement can be reset at any time. Stoppages in the journey with the ignition off are not included in the calculations. Instruments, Controls Ü Board Computer BC 1 BC 2 Timer 19,5° 19:36 All values 1 257.0 Ø 40 8 7.0 Ø 48.0 Ü Reset BC 1 19,5° 19:36 mph gal miles/gal 257.0 Ø 40 7.0 Ø 48.0 miles mph gal miles/gal Restart trip computer The measurement or calculation of the following trip computer information can be restarted: The information of both trip computers can be reset separately and therefore provides a facility for evaluating information over different time periods. z distance travelled, Select the required trip computer information and confirm. z average speed, z effective consumption, z average consumption. Select BC 1 or BC 2 from the trip computer menu. 19,5° 19:36 All values All values miles Ü Reset BC 1 83 The value for the selected function will be reset and recalculated. 257.0 Ø 40 7.0 Ø 48.0 miles mph gal miles/gal To reset all information of a trip computer, select menu item All values. After resetting, "- - - " is displayed with the trip computer information selected. The recalculated values are displayed after a brief delay. Interruption of power supply If the power supply has been interrupted or if the battery voltage has dropped too low, the values stored in the trip computer will be lost. 84 Instruments, Controls The stop watch information to be displayed can be selected via menu Options 3: Ü Board Computer 19,5° 19:36 BC 1 BC 2 00:00:00 Timer Start Reset Options Stop watch Select menu item Timer from the Board Computer menu. The Timer menu is displayed. To start, select menu item Start. To stop, select menu item Stop. To reset, select menu item Reset. Driving Time excl. Stops Measurement of the time the vehicle is in motion. Stationary time is not included. Driving Time incl. Stops Measurement of the time the vehicle is in motion. The time the vehicle is stationary with the key in the ignition switch is included. Travel Time Measurement of the time from manual activation via Start to manual deactivation via Reset. Warning buzzers When starting the engine or whilst driving: z if seat belt 3 is not fastened; z upon operation of retractable steel roof or boot lid if the handbrake is not applied; z upon operation of retractable steel roof if the roof lock is not released; z upon operation of retractable steel roof if luggage compartment partition is not folded back; z when starting off if retractable steel roof is not completely open or closed; z when starting off if the boot lid is not completely closed; z if the vehicle is equipped with Easytronic transmission 3 and the driver’s door is opened when the engine is running, a gear is engaged and the footbrake is not depressed. When the vehicle is parked and the driver’s door is opened: z with the key in the ignition, z with parking lamps or dipped beam on, z If the turn signal stalk is engaged. Instruments, Controls 85 Adjustable wiper interval 3 Setting wiper interval to a value between 2 and 15 seconds: Stalk to timed interval wipe $ , move stalk to position §, wait until wiping frequency reaches the required interval time, stalk back to timed interval wipe $. The interval time selected remains stored until it is next changed or until the ignition is turned off. After turning on the ignition and setting the stalk to $ , the interval is set to 7 seconds. Windscreen wipers To activate, move stalk briefly up. & % $ § = = = = Fast Slow Adjustable timed interval wipe Off Windscreen washer system Pull stalk towards steering wheel. Washer fluid sprays onto the screen and the wipers are engaged for a few wipe movements. 86 Lighting Lighting Versions with daytime running lamps 3 With ignition on and light switch to 7, the dipped beam is switched on without instrument panel lighting. The daytime running lamps switch off when the ignition is switched off. Follow the regulations of the country in which you are driving when using daytime running lamps and front fog lamps 3. Driving abroad 3 89. Exterior lights ....................................... Main beam, headlamp flash .............. Turn signal lamps ................................ Reversing lamps................................... Front fog lamps >3 ........................... Fog tail lamp r ................................... Hazard warning lamps ....................... Headlamp range adjustment ?......... Door-to-door lighting 3 ...................... Instrument illumination k ................... Information display illumination 3..... Courtesy lamp 0 ................................ Battery discharge protection 3 .......... Misted lamp covers ............................. Headlamps when driving abroad ...... 86 87 87 87 87 87 88 88 88 89 89 89 89 89 89 Exterior lights Turn light switch: 7 8 9 = = = Off Parking lamps Dipped beam or main beam In positions 8 and 9, the tail lamps and number plate lamps are also on. If the ignition is switched off with the dipped beam or main beam on, the parking lamps illuminate 3. Lighting 87 Main beam, headlamp flash Turn signal lamps Front fog lamps >3 To switch from dipped to main beam, push stalk forwards Stalk up To switch to dipped beam, push stalk forwards again. Stalk down = The front fog lamps can only be switched on when both the ignition and headlamps are on. To activate the headlamp flash, pull stalk on steering wheel. Main beam is engaged for the duration of activation. If the stalk is moved past the resistance point, the turn signal lamp remains on. When the steering wheel moves back toward the straight-ahead position, the turn signal lamp is automatically deactivated. Fog tail lamp r The fog tail lamp can only be switched on both the ignition and dipped beam/ parking lamps are on. Brief flash: push stalk to resistance point and release. Reversing lamps = Turn signal lamp right Turn signal lamp left The turn signal lamps can be deactivated manually by returning the stalk to the centre position. Operated with the > button. Operated with the r button. The reversing lamps come on when the ignition is on and reverse gear is engaged. 88 Lighting Hazard warning lamps Headlamp range adjustment ? Door-to-door lighting 3 Operated with the ¨ button. Adjust headlamp range to the vehicle load with dipped beam switched on: Turn adjuster wheel to required position. Dipped beam illuminates for approx. 30 seconds after switching on and closing the driver’s door. Adjustment positions To activate 1. Switch off ignition. To aid location of the pushbutton, the red surface is illuminated when the ignition switched on. When the button is pressed, its control indicator flashes in time with the hazard warning lamps. 0 1 2 = = = Driver’s seat occupied Seats occupied Seats occupied and full load in luggage compartment Position 3 is not used. 2. Remove ignition key. 3. Open driver’s door. 4. Pull turn signal stalk toward steering wheel. 5. Close driver’s door. If the driver’s door is left open, lighting will go out after two minutes. The lighting goes out immediately if the ignition key is inserted or the turn signal stalk on the steering wheel is pulled again. Lighting 89 Battery discharge protection 3 Some consumers such as the interior lighting switch themselves off after approx. 30 minutes if the ignition is off in order to protect the battery charge. Misted lamp covers The inside of the lamp covers may briefly mist up under unfavourable wet/cold weather conditions, during heavy rain or after the vehicle has been washed. The misting disappears of its own accord after a short time, but can be accelerated by switching on the headlamps. Instrument illumination k Courtesy lamp 0 Comes on with headlamps. Brightness can be adjusted with adjuster wheel. Automatic interior lamp Activates automatically when a door is opened. Information display illumination 3 Comes on when the ignition or Infotainment system is on. Brightness can be adjusted with adjuster wheel. Goes off automatically after a delay 3 when the doors are closed or immediately when the ignition is switched on 3. Front courtesy lamp Manual operation from inside with doors closed: On Off = = Press light switch 0 Press light switch 0 again. Luggage compartment 3 The luggage compartment lighting comes on when the luggage compartment is open. Headlamps when driving abroad The asymmetrical dipped beam increases the field of vision on the passenger side of the lane. This causes glare for oncoming traffic if the vehicle is driven in countries where traffic drives on the opposite side of the road. To avoid dazzle, have a workshop convert the headlamps. 90 Infotainment system Infotainment system Radio reception 3 Radio reception may be disrupted by static, noise, distortion or loss of reception due to z changes in distance from the transmitter, z multi-path reception due to reflection and z shadowing. Radio reception 3................................ Remote control on steering wheel 3 .. AUX input 3......................................... Infotainment system 3........................ Mobile telephones and radio equipment (CB) 3 ............................. 90 90 91 91 91 Remote control on steering wheel 3 The functions of the Infotainment system 3 and the information display can be operated with the buttons on the steering wheel. Further information 3 76, and the Infotainment system instructions. Infotainment system Mobile telephones and radio equipment (CB) 3 The Vauxhall installation instructions and the operating guidelines provided by the telephone manufacturer must be observed when fitting and operating a mobile telephone. Failure to do so could invalidate the vehicle’s operating permit (EU Directive 95/54/EC). Prerequisites for fault-free operation: z professionally installed exterior antenna to obtain the maximum range possible, AUX input 3 The AUX input is in the centre console between the seats. An external audio source such as portable CD player can be connected using a 3.5 mm jack plug via the AUX input. Always keep the AUX input clean and dry. Further information in the Infotainment system instructions. Infotainment system 3 The Infotainment system is operated as described in the operating instructions. 91 Use of a hands-free attachment without external antenna with mobile telephone standards GSM 900/1800/1900 and UMTS is only permitted if the maximum transmission power of the mobile telephone is 2 Watts for GSM 900 or 1 watt for the other types. For reasons of safety, we recommend that you do not use the phone while driving. Even use of a hands-free set can be a distraction while driving. Be sure to observe any country-specific regulations. z maximum transmission power 10 Watts, 9 Warning z installation of the telephone in a suitable spot (see information 3 60). Mobile phones which do not comply with the above standards, and radios, may only be used with antennae installed on the outside of the vehicle. Seek advice on predetermined installation points for the external antenna or equipment holder and ways of using devices with a transmission power exceeding 10 Watts. We recommend using your Vauxhall Authorised Repairer who keeps consoles and various fitting kits in stock as accessories and will fit these professionally. Caution Mobile phones and radios can cause malfunctions of the vehicle electronics when operated inside the vehicle without an external antenna unless the instructions above are observed. 92 Climate control Climate control Heating and ventilation system, air conditioning system 3................. Air vents ............................................... Heating and ventilation system ......... Air conditioning system 3................... Air intake .............................................. Pollen filter ........................................... Regular operation ............................... Service .................................................. 92 92 94 96 99 99 99 99 Heating and ventilation system, air conditioning system 3 Ventilation, heating and cooling 3 are combined into one unit that is designed to provide comfort regardless of the season, weather or outside temperature. When cooling 3 is activated, the air is cooled and dried. The heating unit heats the air as required in all operating modes depending on the position of the temperature rotary knob. The air supply can be adjusted to suit requirements by means of the fan. The buttons for cooling n and air recirculation 4 are only found on versions with air conditioning system 3. Air conditioning system 3 3 96. Air vents At least one air vent must be open while cooling 3 (air conditioning compressor) is on, in order to prevent the evaporator from icing up due to lack of air movement. The interior ventilation can be adjusted to a comfortable level by adjusting the temperature rotary knob. To increase the air supply, turn the fan all the way up and set the air distribution rotary knob to M or L. Climate control Centre and side (1) air vents Direct the flow of air by tilting and swivelling the slats. 93 Additional air vents Located beneath the windscreen and the side windows, and also in the footwell. Temperature rotary knob in central area: that air that comes out of the centre air vents is cooler than the air coming out of the side air vents. To close the air vents, push the slider towards the centre of the vehicle. Windscreen defroster nozzles (2) Air distribution rotary knob set to V or J: Air is directed onto the windscreen and door windows. 94 Climate control Heating and ventilation system Temperature Adjustment with left-hand rotary knob. Red area Blue area = = Warm Cold The amount of heat is dependent on the coolant temperature and is thus not fully attained until the engine is warm. Air flow Adjustment with central rotary knob. x Off 1-4 Selected fan speed The rate of air flow is determined by the fan. The fan should therefore also be switched on during a journey. Air distribution Adjustment with right-hand rotary knob. V J K L M Towards windscreen and door windows Towards windscreen, door windows and footwell Towards footwell Towards head area and footwell Towards head area Open the air vents when the rotary knob is set to L or M. Climate control 95 Heating For rapid warming of the passenger compartment: z Turn the temperature rotary knob clockwise as far as it will go (warm), z set the fan speed to 3, z set air distribution rotary knob to required position, preferably position J 3 94. The comfort and general well-being of the vehicle occupants are to a large extent dependent on a suitable ventilation and heating setting. Ventilation z Set the temperature to the required setting, z switch on fan, adjust fan setting as required, z for maximum ventilation in head area: Set air distribution rotary knob to M and open all air vents, z for ventilation to footwell: Set air distribution rotary knob to K, z for simultaneous ventilation to the head area and the footwell: Set air distribution rotary knob to L. To achieve a stratification of temperature with a pleasant "cool head and warm feet" effect, set the rotary air distribution rotary knob to K, J or L, set temperature rotary knob to any position (in centre range for best temperature stratification effect). Heating the footwell z Set the temperature rotary knob to the right-hand zone. z Switch on fan. z Set air distribution rotary knob to K. 96 Climate control z Set fan speed to 3 or 4, Air conditioning system 3 z Set air distribution rotary knob to V. As a supplement to the heating and ventilation system, the air conditioning system cools and dehumidifies (dries) inflowing air. z Activate heated rear window Ü, z Open side air vents as required and direct them towards door windows. z For simultaneous footwell heating, set air distribution rotary knob to J. If cooling or dehumidification is not required, switch off cooling in order to save fuel. Cooling switches off automatically at low outside temperatures. Demisting and defrosting windows 9 Warning Disregard of the instructions could lead to misting or icing of the windows and subsequent accidents due to impaired visibility. In the event of misted or icy windows, such as in damp weather, from wet clothes or when outside temperatures are low: z Turn the temperature rotary knob clockwise as far as it will go (warm). Climate control 97 9 Warning The air recirculation system minimises the entry of outside air. The humidity increases, and the windows can mist up. The quality of the passenger compartment air deteriorates which may cause the vehicle occupants to feel drowsy. Air distribution to V: the air recirculation system is automatically switched off to speed up window demisting and prevent fogging. Cooling n Only operate with the engine and fan running. Activate and deactivate with the n button. Air recirculation system 4 The air recirculation mode of the ventilation system is activated and deactivated by pressing the 4 button. When cooling (air conditioning compressor) is active, the air is cooled and dehumidified. If cooling or dehumidification is not required, switch off cooling in order to save fuel. If fumes or unpleasant odours penetrate from outside: Temporarily switch on air recirculation system 4. Cooling switches off automatically at low outside temperatures. When cooling operates, condensation forms and drips from the underside of the vehicle. To increase the cooling power at high outside temperatures, temporarily switch on the air recirculation system. 98 Climate control Comfort setting z Set cooling n as required. z Air recirculation system 4 off. z Set temperature rotary knob as required. z Switch on fan at required speed z Set air distribution rotary knob to M or L. z Open air vents as required. Temperature rotary knob in centre of adjustment range: warmer air will flow into the footwell and cooler air into the upper zone, with warmer air coming from the side air vents and cooler air from the centre air vents. Maximum cooling Briefly open windows to allow heated air to escape quickly. z Cooling n on. z Air circulation system 4 on. z Turn the temperature rotary knob anticlockwise as far as it will go (cold) z Set fan speed to 4, z Set air distribution rotary knob to M. z Open all air vents. Demisting and defrosting windows 9 Warning Disregard of the instructions could lead to misting or icing of the windows and subsequent accidents due to impaired visibility. In the event of misted or icy windows, such as in damp weather, from wet clothes or when outside temperatures are low: Climate control Regular operation z Cooling n on, the air conditioning compressor automatically switches off in low outdoor temperatures (ice formation), For consistently good operation, cooling (air conditioning compressor) 3 must be switched on for several minutes once per month regardless of the weather and the time of year. Operation with the air conditioning compressor switched on is not possible at low outside temperatures. z Turn the temperature rotary knob clockwise. z Set fan speed to 3 or 4. z Air distribution rotary knob to V, air recirculation system 4 automatically switches off, Service For optimal cooling performance, we recommend that the climate control system be checked annually, starting 3 years after initial vehicle registration. – or – if there is still moisture in the system after previous air conditioning operation, the windows may mist up. To prevent this, set air distribution to K before starting engine and set to V approx. 5 seconds after starting. z Activate heated rear window Ü. z Open side air vents as required and direct them towards the side windows. 99 z Functionality and pressure test. Air intake z Heating functionality. The air intakes in front of the windscreen on the far right and left sides of the engine compartment must be kept clear to allow air intake. Remove any leaves, dirt or snow. z Leakage check. Pollen filter The pollen filter cleans dust, soot, pollen and spores from the air entering from outside. The active carbon layer 3 eliminates most odours and noxious environmental gases from the air. z Check of drive belts. z Cleaning of condenser and evaporator drainage. z Performance check. 100 Driving and Operation Driving and Operation Easytronic 3 ......................................... Manual transmission ........................... Driving hints ......................................... Saving fuel, protecting the environment ...................................... Fuel, refuelling ..................................... Catalytic converter, engine emissions Drive control systems .......................... Hydraulic brake system ...................... Anti-lock Braking System (ABS u) .... Handbrake ........................................... Brake assist .......................................... Wheels, tyres ........................................ 100 105 106 108 110 112 114 119 120 121 121 121 Easytronic 3 The Easytronic transmission 3 permits manual gearshifting (Manual mode) or automatic gearshifting (Automatic mode), both with automatic clutch control. Transmission display Shows the mode or current gear. If the Winter programme is activated, T is illuminated. Driving and Operation 101 Selector lever in o (centre position) Once the selector lever has been moved from N to position o (centre position) with the footbrake depressed, the Easytronic is in automatic mode and first gear has been selected (second gear with Winter programme enabled). "A" appears in the transmission display. When the footbrake is released the vehicle starts to "creep". If the footbrake is not depressed, "A" flashes. Start off by pressing the accelerator immediately or more selector lever back to N and repeat procedure with footbrake depressed. Starting the engine When starting the engine, activate the footbrake at the same time. The engine can only be started in position N and with the footbrake activated. The transmission display shows "N". If the footbrake is not activated, the control indicator j 3 illuminates in the instrument cluster and "N" flashes in the transmission display; the engine cannot be started. Also the vehicle cannot be started if all brake lamps have failed. Operating Easytronic with the selector lever Always move the selector lever all the way to the stop. Note the gear or mode indicator in the transmission display. Selector lever in N Neutral. Shifting to different gears takes place automatically in automatic mode, depending on the driving conditions. 102 Driving and Operation Selector lever in + or + Shift to a higher gear. Shift to a lower gear. If a higher gear is selected when the running speed is too low, or a lower gear when the speed is too high, no shift is effected. This prevents the engine from running at too low or too high revs. Selector lever in A/M Switch between Automatic and Manual mode. In Manual mode, gears can be selected manually by moving the selector lever to + or -. The current gear is indicated in the transmission display. If the engine speed is too low, Easytronic will automatically shift to a lower gear even in Manual mode. This prevents the engine from stalling. Stopping the vehicle In Automatic and Manual mode, when the vehicle has stopped, first gear (second gear with Winter programme engaged) is engaged automatically and the clutch is disengaged. In R, reverse gear remains engaged. Gears can be skipped by jogging the selector lever repeatedly at short intervals. If a warning signal sounds when the driver’s door is opened (footbrake not depressed), move the selector lever to N and apply the handbrake. When the vehicle is in Automatic mode, the Easytronic shifts to Manual mode when the selector lever is set to position + or -. The transmission display shows the currently selected gear. When stopping on gradients, apply the handbrake or depress the brake pedal. To prevent overheating of the clutch, do not increase engine speed to ensure smooth idling when in gear. Selector lever in R Reverse gear. Engage only when vehicle is stationary. Switch off engine if stopping for a lengthy period, e.g. in traffic jams or at level crossings. Press button on selector lever, select R. The transmission display shows "R". Electronically controlled driving programmes in automatic mode z The operating temperature programme increases the engine speed after a cold start to bring the catalytic converter to the required temperature quickly. If R is selected when the vehicle is in motion, "R" flashes in the transmission display and no gear is engaged. z Adaptive programmes automatically adapt gear selection to suit the driving conditions, such as if the vehicle has a high payload, or is being driven on inclines. Driving and Operation 103 Engine braking Automatic mode: When driving downhill, the Easytronic does not shift into higher gears until a fairly high engine speed has been reached. When braking, it shifts down in good time. Manual mode: To utilise the engine braking effect, select a lower gear in good time when driving downhill. Winter programme T In the event of difficulties starting-off on slippery roads, press button T ("A" and T appear in the transmission display). The Easytronic switches to Automatic mode and the vehicle sets-off in second gear. Kickdown If the accelerator pedal is pressed past the pressure point, the transmission shifts to a lower gear, depending on engine speed. The Winter programme is switched off by: When the engine speed approaches its upper limit, the transmission shifts to a higher gear during kickdown even in Manual mode. z pressing the T button again, z turning off the ignition, z switching to Manual mode, z when clutch temperature is too high. During kickdown, no manual gearshifting is possible. Without kickdown this automatic shift is not effected in Manual mode. "Rocking" the vehicle Only if it becomes necessary to rock the vehicle to free it from sand, mud, snow or a hole, move the selector lever between o (centre position) and R in a repeat pattern. Do not race the engine and avoid sudden acceleration. 104 Driving and Operation Vehicle storage Apply handbrake and remove ignition key. The most recently engaged gear (indicated in transmission display) remains engaged. With N, no gear is engaged. When the ignition is switched off, the Easytronic no longer responds to movement of the selector lever. If the ignition key is not removed, the battery may be discharged if the vehicle is then left to stand for a lengthy period of time. Manoeuvring the vehicle To manoeuvre the vehicle back and forth during attempts to park or in garage entrances the creeping movement can be utilised by releasing the footbrake. Never actuate accelerator and brake pedals simultaneously. In order to prevent damage, the Easytronic disengages the "creep function" at extremely high automatic clutch temperatures. If the handbrake has not been applied, the control indicator R flashes in the instrument cluster for a few seconds after the ignition is switched off. Fault To prevent damage to the Easytronic, the clutch is engaged automatically at high clutch temperatures. Control indicator A illuminates in the event of a fault. Continued driving is possible. Manual mode can no longer be used for shifting. If "F" also appears in the transmission display, it is not possible to continue driving. Have the cause of the fault eliminated by a workshop. The self-diagnosis integrated into the system allows rapid fault identification. Driving and Operation 105 3. Clean transmission around the cap (see Fig. 16435 S) so that no dirt can get into the opening when the cap is removed. 4. Rotate cap to slacken and remove by lifting upwards – see Fig. 16435 S. 5. Turn the adjusting screw clockwise using a flat-head screwdriver (vehicle tools 3 133) until clear resistance can be felt. The clutch has now been disengaged. Caution Do not turn beyond the resistance, since this can damage the Easytronic. Interruption of power supply The clutch is not disengaged if there is an interruption of the power supply when a gear is engaged. The vehicle cannot move. If the battery is discharged, start the vehicle using jump leads 3 127. If the cause is not a discharged battery, contact a workshop. If the vehicle must be removed from moving traffic, disengage the clutch: 1. Apply handbrake and switch off ignition. 2. Open bonnet and engage support. 6. Fit cleaned cap again. The cap must be in full contact with the housing. Caution Towing the vehicle and starting the engine is not permitted when the clutch has been disengaged in this way, although the vehicle can be moved a short distance. Contact a workshop immediately. Manual transmission To engage reverse, with the vehicle stationary, depress the clutch pedal, wait 3 seconds, then raise ring under gearshift lever and engage gear. If the gear does not engage, set the lever in neutral, release the clutch pedal and depress again; then repeat gear selection. Do not grind the clutch unnecessarily. When operating, depress the clutch pedal completely. Do not use the pedal as a foot rest (increases clutch wear). 106 Driving and Operation Driving hints The first 600 miles (1000 km) Drive your vehicle at various speeds. Do not use full throttle. Never allow the engine to labour at low revs. Make good use of all gears. Depress the accelerator pedal a maximum of approx.3/4 of the available pedal travel in all gears. Do not drive faster than three quarters of maximum speed. Do not brake unnecessarily hard for the first 125 miles (200 km). During the first drive, smoke may develop because of wax and oil evaporating off the exhaust system. Park the vehicle in the open for a while after the first drive and avoid inhaling the fumes. Fuel and engine oil consumption is higher than normal during the running-in period. Never coast with engine not running Many units will not function in this situation (e.g. brake servo unit, electric powerassisted steering). Driving in this manner is a danger to yourself and others. Brake servo unit When the engine is not running, the brake servo unit is no longer effective once the brake pedal has been depressed once or twice. Braking effect is not reduced, but significantly greater force is required for braking. Electric power-assisted steering If the electric power-assisted steering fails when being towed with the engine switched off, the vehicle can still be steered, but considerably more force is required. Driving in mountainous terrain The cooling fan is electrically operated. Its cooling power is therefore independent of the engine speed. Since a considerable amount of heat is generated at high engine speeds and less at slower speeds, do not shift down when climbing hills whilst the vehicle is still coping with the gradient in the higher gear. Switching off the engine When you switch off, fans in the engine compartment may continue running for a time to cool the engine. If the engine temperature is very high, e.g. after driving in mountainous terrain: Allow the engine to idle for approx. 2 minutes, in order to prevent heat accumulation. Vehicles with turbocharged engine After running at high engine speeds or high engine loads, operate the engine briefly at a low load or run in neutral for approx. 30 seconds before switching off, in order to protect the turbocharger. Save energy – more miles Please observe the running-in hints on the previous page and the tips for saving energy on the following pages. Good, technically correct and economical driving ensures maximum durability and performance for your vehicle. Driving and Operation Overrun cut-off The fuel supply is automatically cut-off during overrun, e.g. when the vehicle is driven with a gear engaged but the accelerator pedal is not depressed. Overrun cut-off is deactivated if catalytic converter temperature is high. Vehicles with turbocharged engine Flow-generated noises may be audible if the accelerator is released quickly, on account of air flow in the turbocharger. Engine speed Drive in a low engine speed range for each gear as much as possible. Warming up Allow the engine to warm up while driving. Do not warm it up by letting it run at idling speed. Do not apply full throttle until the engine has reached operating temperature. After a cold start, the Easytronic 3 does not shift to higher gears until the speed increases when it is in Automatic mode. This allows the catalytic converter to quickly reach the temperature that is required for optimum emission reduction. Correct gear selection Do not race your engine whilst in neutral or with a low gear selected. Driving too fast in individual gears as well as stop-and-go traffic increases engine wear and fuel consumption. Change down When decreasing speed, shift down into the next lowest gear. Do not slip the clutch with a high-revving engine. This is especially important when hill climbing. 107 Cooling fan The cooling fan is controlled via a thermoswitch and therefore only runs if necessary. Pedals Do not place any objects in the footwell which could slip under the pedals and inhibit the pedal travel. To ensure the pedal travel is uninhibited, there must be no mats in the area of the pedals. Battery care When driving slowly or when the vehicle is stationary, e.g. in slow urban traffic, stopand-go traffic or traffic jams, turn off all unnecessary electrical loads where possible (e.g. heated rear window, heated seats). Depress clutch pedal when starting, in order to relieve the strain on the starter and the battery. 108 Driving and Operation Saving fuel, protecting the environment Trend-setting technology In the development and manufacture of your vehicle, environment-friendly and in the main recyclable materials were used. The production methods used to make your vehicle are likewise environmentallycompatible. Recycling of production wastes keeps the circulation of material closed. Reduction of energy and water requirements also helps to conserve natural resources. A highly advanced design means that your vehicle can be easily disassembled at the end of its working life, and the individual materials separated for subsequent re-use. Materials such as asbestos and cadmium are not used. The refrigerant in the air conditioning system 3 is CFC-free. New painting techniques employ water as a solvent. End-of-Life Vehicle recovery For detailed information on Vauxhall’ s ongoing commitment to achieving an environmentally sustainable future, including; design for recycling, take back of End-of-Life Vehicle (ELVs) and the recycling of ELVs, view www.Vauxhall.co.uk/recycling for details. Energy and environment-conscious driving z High noise levels and exhaust emissions are often a result of driving without due attention to saving energy and protecting the environment. z You should therefore drive with energy in mind "more miles – less fuel". Reduce the noise level and exhaust emissions by adopting an environmentconscious driving style. This is extremely worthwhile and improves the quality of life. Fuel consumption depends to a great extent on your own personal driving style. The following hints are intended to help you consume fuel at a rate that is as close as possible to the specified levels 3 172. Check your vehicle’s fuel consumption every time you refuel. This facilitates early detection of any irregularities causing increased fuel consumption. Warming up z Full throttle and warming up at idle speed increase wear, fuel consumption, exhaust emission, the amount of pollutant in the exhaust and the amount of noise. z Drive off immediately after starting. Warm up the engine by running it at moderate engine speeds. Uniform speed z Hectic driving significantly increases fuel consumption, the exhaust emissions, the proportion of pollutant in the exhaust gas and the noise level. z Do not accelerate and brake unnecessarily. Drive at uniform speed, watching the road. Avoid frequent starting off and stopping e.g. at traffic lights, in short distance traffic and in queues of traffic by means of clever planning. Select roads with good traffic flow. Idling z The engine also consumes fuel when idling. z If you have to wait for more than one minute, it is worthwhile switching off the engine. Five minutes of idling corresponds to approx. 0.6 miles (1 km) of driving. Driving and Operation Overrun z The fuel supply is automatically cut-off during overrun, e.g. when the vehicle is being driven down long gradients or when braking 3 109. z To enable the overrun cut-off to come into action and save fuel, do not accelerate or depress clutch pedal during overrun. Correct gear selection z High revs increase engine wear and fuel consumption. z Do not race your engine. Avoid driving at high engine speeds. Making use of the tachometer helps to save fuel. Drive in a low engine speed range for each gear as much as possible with uniform engine speeds. Drive as often as possible in top gear, select the next higher gear as soon as possible, and only change down when the engine is no longer running perfectly smoothly. High speed z The higher the speed, the higher the consumption and the noise level. At top speed, you consume a great deal of fuel and produce excessive noise and exhaust emissions. z Slightly releasing the accelerator pedal results in distinct fuel savings with no major loss of speed. Drive at no more than approx. three quarters of maximum speed and you will use up to 50% less fuel, without losing a great deal of time. Tyre pressure z Inadequate tyre pressure, leading to higher road resistance, costs money in two ways: for more fuel and increased tyre wear. z Regular checks (every 14 days) pay off. Electrical loads z The power consumption of electrical equipment increases fuel consumption. z Switch off all auxiliary electrical loads (e.g. air conditioning 3, heated rear window) when not needed. 109 Repair and maintenance z Improper repairs or adjustment and maintenance work can increase fuel consumption. Do not carry out work on the engine yourself. You may, out of ignorance, infringe environmental laws by not disposing of materials properly. Appropriate parts might not be recycled. Contact with some of the materials involved may pose a health hazard. z We recommend that repair and maintenance be entrusted to your Vauxhall Authorised Repairer. Extreme driving conditions z Going up steep slopes, cornering, driving on poor roads and winter driving all increase fuel consumption. Fuel consumption increases dramatically in urban traffic and at winter temperatures, especially on short trips when the engine operating temperature is not reached. z Follow the hints given above to keep consumption to a minimum under such conditions. 110 Driving and Operation Fuel, refuelling Fuel consumption Fuel consumption is determined under specific driving conditions 3 172. Special equipment increases the weight of the vehicle. As a result, they can increase fuel consumption and reduce the specified maximum speed. There is increased friction between engine and transmission parts during the first 600 miles (1000 kilometres). This increases fuel consumption. Fuel for petrol engines Only use unleaded fuel that complies with DIN EN 228. Fuels with ethanol content greater than 5% may only be used if the vehicle has been specifically developed and approved for these fuels. Use fuel with the recommended octane rating (value in bold 3 170). Use of fuel with too low an octane rating can reduce engine power and torque and slightly increases fuel consumption. Caution Use of fuel with too low an octane rating could lead to uncontrolled combustion and engine damage. Fuel for diesel engines Only use diesel fuel that complies with DIN EN 590. The fuel must have low sulphur content (maximum 50 ppm). Since January 2004, some oil companies have mixed their diesel fuel with upto 5% Bio fuel (FAME = Fatty Acid Methyl Esters) like RME (Rape-Oil Methyl Ester). This is in accordance with the current DIN EN 590 and does not harm the fuel/injection system. The characteristics of a diesel fuel mixed up with 5% Bio fuel (FAME) do not differ from conventional diesel fuel and do not influence the vehicle’s driveability. Important: Diesel fuel mixed with 5% FAME according to DIN EN 590 must not be confused with 100% Bio Diesel, which is not to be used in Vauxhall engines. The flow and filterability of diesel fuel are temperature-dependent. Diesel fuels with improved low temperature properties are therefore available on the market during the winter months. Make sure that you fill the tank with winter fuel before the start of the cold weather season. Additives can be used with diesel fuels with winter properties that are guaranteed by the manufacturer and when using diesel fuel filters that are heated depending on the outside temperature. Diesel fuels must not be diluted with fuels that are intended for petrol engines. Driving and Operation Fuel filler cap Only a Vauxhall genuine fuel filler cap provides full functionality. Diesel-engined vehicles have special fuel filler caps. 111 Open the tank flap. Unscrew fuel filler cap to open and suspend from tank flap. The fuel tank has a limiting system which prevents overfilling of the tank. Refuelling 9 Warning Correct filling depends to a large extent on proper operation of the fuel dispensing pump: Before refuelling, switch off engine and external heaters with combustion chambers. Switch mobile phones off. Follow the operating and safety instructions of the filling station when refuelling. 1. Fully insert the filler nozzle and switch it on. 9 Warning Fuel is flammable and explosive. No smoking. No naked flames or sparks. If you can smell fuel in your vehicle, have the cause of this rectified immediately by a workshop. Fuel filler neck at right rear side of vehicle. The tank flap is unlocked with the doors 3 23. 2. After the automatic cut-off the nominal capacity of the fuel tank can be obtained by topping up with two doses of fuel. Make sure the nozzle is fully inserted. To close, position the fuel filler cap and rotate past the resistance until the cap audibly clicks over the retainer. Close tank flap. Caution Wipe off any overflowing fuel immediately. 112 Driving and Operation Caution Damage to the catalytic converter or the vehicle may result if the following points are not observed. z In the event of misfiring, uneven engine running, a clear reduction in engine performance or other unusual problems, have the cause of the fault rectified by a workshop as soon as possible. In an emergency, driving can be continued for a short period, keeping vehicle speed and engine speed low. Catalytic converter, engine emissions Catalytic converter The catalytic converter reduces the amount of harmful substances in the exhaust gas, such as carbon monoxide (CO), hydrocarbons (CH) and nitrous oxide (NOx). Fuel grades other than those listed on page 110 (e.g. LRP = Lead Replacement Petrol or leaded fuel) could damage the catalytic converter or electronic components. This does not apply when the Electronic Stability Programme (ESP®Plus 3) kicks in 3 114. z If unburned fuel enters the catalytic converter of a petrol engine, this may result in overheating and irreparable damage to the catalytic converter. You should therefore avoid unnecessarily long use of the starter when starting off, running the tank dry and starting the engine by pushing or towing. Controlling exhaust emission Some of the damaging substances in the exhaust such as carbon monoxide (CO), hydrocarbons (HC) and nitrous oxides (NOx) are reduced to a minimum by making structural changes – mainly in the injection system and the ignition system in conjunction with the catalytic converter. Driving and Operation 113 If it illuminates briefly, but does not recur, it is of no significance. Illumination of control indicator A can indicate water in the diesel fuel filter. Check fuel filter for possible water residue 3 162. If it flashes after the ignition is switched on, there is a fault in the immobiliser system. The engine cannot be started 3 21. Control indicator Z for exhaust Illuminates when the ignition is switched on and during the start attempt. Goes off shortly after the engine starts running. Illuminated with the engine running indicates a fault in the exhaust gas cleaning system. The permitted emissions may be exceeded. Contact a workshop immediately. Flashing with the engine running indicates a fault which could lead to catalytic converter damage. You may continue driving without damage if you slow down until flashing stops and the control indicator comes on. Contact a workshop immediately. Control indicator A for engine electronics Comes on for a few seconds after the ignition is turned on. If it illuminates when the engine is running, there is a fault in engine or transmission electronics. The electronic system switches to an emergency running programme. Fuel consumption may be increased and the driveability of the vehicle may be impaired. In some cases, faults can be eliminated by switching off the engine and restarting. If the control indicator comes on again when the engine is running, contact a workshop to eliminate the cause of the fault. 114 Driving and Operation Engine exhaust 9 Warning Engine exhaust gases contain poisonous carbon monoxide, which is colourless and odourless and could be fatal if inhaled. If exhaust gases penetrate the vehicle interior, open a window and contact a workshop. Maintenance Have all maintenance work carried out at the intervals specified. We recommend that you entrust this work to your Vauxhall Authorised Repairer, who has proper equipment and trained personnel available. Electronic testing systems permit rapid diagnosis and remedy of faults. This way you can be certain that all components of the vehicle’s electrical, injection and ignition systems operate correctly, that your vehicle has a low level of pollutant emission and that the catalytic converter system will have a long service life. You are thereby making an important contribution towards keeping the air clean and compliance with emissions legislation. Checking and adjustment of the fuelinjection and ignition systems is included in service inspections. For this reason, you should have all maintenance work carried out at the intervals specified in the chapter “Service and Maintenance” 3 152. Drive control systems Electronic Stability Programme (ESP®Plus) 3 ESP®Plus improves driving stability when necessary in any driving situation, regardless of the type of road surface or tyre grip. It also prevents the drive wheels from spinning. Driving and Operation As soon as the vehicle starts to swerve (understeer/oversteer), engine output is reduced and the wheels are braked individually. This considerably improves the driving stability of the vehicle on slippery road surfaces. Illuminates while driving: Fault in the system. Driving can be continued. Poor road surface conditions may however still cause vehicle stability to be impaired. Have the cause of the fault eliminated by a workshop. The self-diagnosis integrated into the system allows rapid fault identification. ESP®Plus is ready for operation as soon as the ignition is switched on and control indicator v goes out. When ESP®Plus comes into action, v flashes. The vehicle is now in a critical situation; ESP®Plus allows you to keep control of the vehicle and reminds you to match your speed to the road conditions. 9 Warning Do not let this special safety feature tempt you into taking risks when driving. Traffic safety can only be achieved by adopting a responsible driving style. Adapt speed to the road conditions. 115 Control indicator v may illuminate when the temporary spare wheel is in use. The system is then deactivated. Control indicator v The control indicator illuminates for a few seconds after the ignition is turned on. The system is ready for operation when the control indicator goes out. Flashing during driving: This shows the system has come into action. The engine output may be reduced (the sound of the engine changes) and the vehicle may be braked automatically to a small degree. Illuminates after interruption of power supply e.g. after disconnecting battery. After a power supply interruption the steering angle sensor must be calibrated to make the system operational: z Automatic calibration by driving in straight line at constant slow speed, i.e. 12 to 25 mph (20 to 40 km/h), on a level, dry road, z Manual calibration by turning steering wheel from limit position to limit position. If the control indicator does not go off after successful calibration, observe notes in previous column. 116 Driving and Operation Cruise control 3 Cruise control can store and maintain speeds of approx. 20 to 125 mph (30 to 200 km/h). Deviation from the stored speed is possible on uphill or downhill inclines. For safety reasons, the cruise control cannot be activated until the footbrake has been depressed once. With Easytronic 3, only use cruise control when in automatic mode. 9 Warning When the cruise control is active, reaction times may be increased due to the different position of the feet. The cruise control is operated with the buttons I, R and O on the turn signal stalk. Do not use the cruise control if it is not advisable to maintain a constant speed (e.g. in situations presenting a danger to yourself and other road users, in heavy traffic or on winding, slippery or greasy roads). To activate Tap button I: the current speed is stored and maintained. The accelerator pedal can be released. Vehicle speed can be increased by depressing the accelerator pedal. When the accelerator pedal is released, the previously stored speed is resumed. Driving and Operation Increase With cruise control active, hold down button I or briefly press it repeatedly: speed is increased continuously or in steps of 1.2 mph (2 km/h). The current speed is stored and saved after button I has been released. Decelerate With cruise control active, hold down button R or briefly press it repeatedly: speed is reduced continuously or in steps of 1.2 mph (2 km/h). The current speed is stored and saved after button R has been released. 117 To deactivate Briefly press the O button: cruise control is deactivated. Stored speed The speed is saved until the ignition is switched off. Automatic deactivation if: To resume the saved speed, briefly press button R at a speed above 20 mph (30 km/h). z the vehicle’s speed drops below approx. 20 mph (30 km/h), or z the brake pedal is depressed, z the clutch pedal is depressed 3, z selector lever with Easytronic 3 is in N. 118 Driving and Operation Ultrasonic parking sensors 3 Parking distance sensors make reverse parking easier by measuring the distance between the rear of the vehicle and obstacles behind it. It is the driver, however, who maintains full responsibility for parking. Fault In the event of system faults, a permanent tone sounds at a distance of 1 metre from the obstacle. Have the cause of the fault eliminated by a workshop. In order to avoid operational problems or erroneous information, the sensors must be undamaged and free of soiling, snow and ice. The system records the distance using four sensors in the rear bumper. To activate The parking distance sensors are activated automatically when the ignition is switched on and reverse gear is engaged. Operational readiness is indicated by a brief tone. If the vehicle approaches an obstacle, a series of acoustic signals sound. The interval between the signals becomes shorter as the vehicle gets closer to the obstacle. When the distance is less than 30 cm, the signal is continuous. 9 Warning Under certain circumstances, various reflective surfaces on objects or clothing as well as external noise sources may cause the system to fail to detect obstacles. To deactivate The system deactivates automatically when reverse gear is disengaged. Driving and Operation 119 When the engine is not running, the assistance of the brake servo unit disappears once the brake pedal has been depressed once or twice. Braking effect is not reduced, but braking requires significantly greater force. This is especially important to bear in mind when towing. The brake fluid level should be checked regularly. If the brake fluid level is too low and the handbrake is not applied, control indicator R illuminates in the instrument cluster 3 70. Hydraulic brake system The brake system comprises two independent brake circuits. If one brake circuit faults, the vehicle can still be braked with the other brake circuit. However the braking effect will occur at a lower pedal position and considerably more force is required. The braking distance will be extended. Contact a workshop before continuing to drive. To ensure the full pedal travel can be utilised, especially in case of a fault in one of the brake circuits, there must be no mats in the vicinity of the pedals 3 107. Brake system control indicator R The control indicator illuminates after the ignition is turned on, when the handbrake is applied or if the brake or clutch fluid level is too low. Brake fluid 3 164. 9 Warning If the control indicator comes on when the handbrake is released, stop driving immediately. Contact a workshop. For vehicles with Easytronic 3, the control indicator flashes for a few seconds when the ignition is turned off if the handbrake is not applied. 120 Driving and Operation Anti-lock Braking System (ABS u) Self-check When the engine is started and the vehicle starts off, the system performs a self-check, which may be audible. ABS prevents the wheels from locking. ABS starts to regulate brake pressure as soon as a wheel shows a tendency to lock. The vehicle remains steerable, even during hard braking. Fault 9 Warning ABS control is made apparent through a pulse in the brake pedal and the noise of the regulation process. If there is a fault in the ABS, the wheels may be liable to lock due to braking that is heavier than normal. The advantages of ABS are no longer available. During hard braking, the vehicle can no longer be steered and may swerve. For optimum braking, keep the brake pedal fully depressed throughout the braking process, despite the fact that the pedal is pulsating. Do not reduce the pressure on the pedal. Control indicator u for ABS It comes on for a few seconds after the ignition is turned on. The system is ready for operation when the control indicator goes out. If the control indicator does not go out after a few seconds, or if it illuminates while driving, there is a fault in the ABS. The brake system remains operational without ABS regulation. Have the cause of the fault eliminated by a workshop. The self-diagnosis integrated into the system allows rapid fault identification. Driving and Operation Brake assist Wheels, tyres If the brake pedal is operated with a fast, powerful push, the vehicle is automatically braked at full braking power in order to achieve the shortest possible braking distance when full-on braking occurs (brake assist). Suitable tyres and restrictions 3 176. Maintain steady pressure on the brake pedal for as long as full-on braking is to continue. When the brake pedal is released, the maximum brake force amplification is taken away. 121 Tyres fitted in the factory are adapted to the chassis and provide optimum driving comfort and safety. Changing tyre/wheel type If tyres of a different size than those fitted at the factory are used, it may be necessary to reprogramme the electronic speedometer and make other vehicle modifications. 9 Warning Handbrake Always apply handbrake firmly without operating the release button, and apply as firmly as possible on a downhill or uphill slope. To release the handbrake, pull the lever up slightly, press the release button and fully lower the lever. To reduce the operating forces of the handbrake, depress the footbrake at the same time. Use of unsuitable tyres or wheels may lead to accidents and render the vehicle unroadworthy. 122 Driving and Operation Fitting new tyres Fit tyres in pairs or in sets, which is even better. Ensure that tyres on one axle are: z the same size, z the same design, z the same make, z and have the same tread pattern. Do not reduce tyre pressure when the tyres are warm. Otherwise the pressure may drop below the permissible minimum when the tyres cool down. Screw on the valve cap after checking pressure. Incorrect tyre pressures will impair safety, vehicle handling, comfort and fuel economy and will increase tyre wear. Fit directional tyres such that they roll in the direction of travel. The rolling direction is indicated by a symbol (e.g. an arrow) on the sidewall. Tyres fitted opposing the rolling direction (such as when changing a tyre) should be refitted as soon as possible. This is the only way to benefit fully from the design properties of the tyre. When disposing of tyres, follow the legal requirements. Tyre pressure Check tyre pressures at least every 14 days and prior to any long journey; the tyres should be checked when cold. Don’t forget to check the spare 3. Tyre pressures 3 176. The tyre pressure data is for cold tyres. It applies to both summer and winter tyres. Driving and Operation 9 Warning If the pressure is too low, this can result in considerable tyre warm-up and internal damage, leading to tread separation and even to tyre blow-out at high speeds. 123 Tyre condition, wheel condition Drive over edges slowly and at right angles if possible. Driving over sharp edges can cause tyre and wheel damage. Do not trap tyres on the kerb when parking. Tread depth Check tread depth regularly. Regularly check the wheels for damage. Seek the assistance of a workshop in the event of damage or unusual wear. The legally permissible minimum tread depth (1.6 mm) has been reached when the tread has worn down as far as one of the tread wear indicators (TWI1)). A number of tread wear indicators are spaced at equal intervals around the tyre within the tread. Their position is indicated by markings on the tyre sidewall. For reasons of safety, tyres should be replaced when their tread depth has worn down to 2 to 3 mm (winter tyres: 4 mm). 1) TWI = Tread Wear Indicator. 124 Driving and Operation General information z The risk of aquaplaning is greater if the tyres are worn. Correct the tyre pressures. Restrictions 3 176. z Tyres age, even if they are used little or not at all. We recommend tyre replacement at the latest every 6 years. Winter tyres (M + S tyres) improve driving safety at temperatures below 7 °C and should therefore be fitted on all wheels. z Never fit used tyres the previous history and use of which you do not know. The design of summer tyres means they have limited qualities for winter driving. Tyre designations Meanings: In accordance with country-specific regulations, affix the speed sticker 3 in the driver’s field of view. e.g. 185/55 R 15 84 H If tread wear is greater in the front than in the rear, switch the front and rear tyres. Winter tyres 3 Notes on fitting new tyres 3 122. 185 = 55 = R 15 82 = = = H = Tyre width in mm Cross-section ratio (tyre height to width in %) Belt type: Radial Wheel diameter in inches Load index e.g. 82 corresponds to 475 kg Speed code letter Speed code letters: Q S T H V W = = = = = = up to 100 mph (160 km/h) up to 112 mph (180 km/h) up to 118 mph (190 km/h) up to 130 mph (210 km/h) up to 150 mph (240 km/h) up to 168 mph (270 km/h) If you use the spare wheel when it is fitted with a summer tyre, the vehicle’s driveability may be affected, especially on slippery road surfaces. Obtain a replacement for the faulty tyre as soon as possible, and have the wheel balanced and fitted to the vehicle. Driving and Operation 125 Wheel trims 3 Use wheel trims and tyres that are approved by Vauxhall for the vehicle in question and therefore meet all the requirements pertaining to the respective wheel/tyre combination. Remove the wheel trims if using tyre chains. If the wheel trims and tyres used are not Vauxhall-approved, the tyres must not have a beaded edge. 9 Warning Tyre chains may only be used at speeds up to 30 mph (50 km/h). They must only be used for brief periods on roads that are free of snow. Damage may lead to tyre blowout. Wheel trims must not impair brake cooling. Remove the wheel trims if fitting tyre chains 3. 9 Warning Use of unsuitable tyres or wheel trims could lead to sudden loss of air and thereby accidents. Tyre chains 3 Restrictions and further notes 3 176. Tyre chains are only permitted on the drive wheels (front axle). They must be fitted to the tyres symmetrically in order to achieve a concentric fit. Always use fine mesh chains that add no more than 10 mm to the tyre tread and the inboard sides (including chain lock). Tyre chains must not be used on the temporary spare wheel. If you need to use tyre chains after suffering a flat front tyre, fit the temporary spare on the rear axle and transfer one of the rear wheels to the front axle. 126 Self-help, Vehicle Care Self-help, Vehicle Care Diesel fuel system, bleeding ............... Bonnet .................................................. Starting the engine with jump leads 3 Towing your own vehicle..................... Warning triangle ¨ 3 and First-aid kit + 3 ......................... Spare wheel 3...................................... Jack £ 3 and vehicle tools 3 ............ Changing wheels ................................. Tyre repair aerosol 3 .......................... Electrical system .................................. Fuses and the most important circuits they protect ....................................... Bulb replacement ................................ Halogen headlamp system dipped and main beam................................. Turn signal lamps ................................ Front fog lamps 3 ............................... Tail lamps............................................. Number plate lamp ............................. Courtesy lamp...................................... Vehicle care.......................................... 126 126 127 129 130 131 133 133 137 138 140 144 144 146 146 147 148 149 150 Diesel fuel system, bleeding Never let the tank run dry! If control indicator Y illuminates, refuel as soon as possible. Refuel immediately if it flashes. If the tank is allowed to run dry, the diesel fuel system must be bled. Switch on the ignition three times for approx. 15 seconds at a time. Then start the engine for a maximum of 40 seconds. Repeat this process after no less than 5 seconds. If the engine fails to start, seek the assistance of a workshop. Bonnet Pull the release lever located on the driver’s side below the instrument panel, and press back to its original position. Self-help, Vehicle Care 127 Starting the engine with jump leads 3 Do not start with a quick charger or by pushing or towing. A vehicle with a discharged battery can be started using jump leads and the battery of another vehicle. Attempts to start the vehicle should be made at intervals of one minute and should not last longer than 15 seconds. 9 Warning Pull the safety catch upwards and open the bonnet. Any dirt or snow on the bonnet can slide down towards the windscreen when the bonnet is opened and block the air intake 3 99. Secure the bonnet support. Before closing the bonnet, press the support into the holder. Lower the bonnet and allow it to drop into the catch. Check that the bonnet is engaged. Be extremely careful when starting with jump leads. Any deviation from the following instructions can lead to injuries or damage caused by battery explosion or damage to the electrical systems of both vehicles. 128 Self-help, Vehicle Care z Use a booster battery with the same voltage (12 volts). Its capacity (Ah) must not be much less than that of the discharged battery. z Use jump leads with insulated terminals and a cross section of at least 16 mm2 (25 mm2 for diesel engines). z Do not disconnect the discharged battery from the vehicle. z Switch off all unnecessary electrical consumers. z Do not lean over the battery during jump starting. z Never expose the battery to naked flames or sparks. z A discharged battery can freeze even at temperatures of 0 °C. Thaw frozen batteries before connecting jump leads. z Do not allow battery fluid to come into contact with eyes, skin, fabrics or painted surfaces. The fluid contains sulphuric acid which can cause injuries and damage in the event of direct contact. z Wear eye protection and protective clothing when handling a battery. z Do not allow the terminals of one lead to touch those of the other lead. z The vehicles must not come into contact with each other during the jump starting procedure. z Apply handbrake. Select neutral gear. Lead connection order: 1. Connect the first lead to the positive terminal (1) of the booster battery. 2. Connect the other end of the lead to the positive terminal (2) of the discharged battery. 3. Connect the second lead to the negative terminal (3) of the booster battery. 4. Connect the other end of the second lead (4) to a vehicle ground point, such as the engine block or a screw connection in the engine suspension. Connect as far away from the discharged battery as possible. Self-help, Vehicle Care 129 Route the leads so that they cannot catch on rotating parts in the engine compartment. To start the engine: 1. Start the engine of the vehicle providing the jump start. 2. After 5 minutes, start the other engine. Start attempts should be made at intervals of 1 minute and should not last longer than 15 seconds. 3. Allow both engines to idle for approx. 3 minutes with the leads connected. 4. Switch on electrical consumers (e.g. light, heated rear window) of the vehicle receiving the jump start. 5. Reverse above sequence exactly when removing leads. Towing your own vehicle Disengage cap at bottom and remove downwards. The towing eye is in the pouch or the stowage compartment for vehicle tools 3 133. Spare wheel 3 131. For reasons of design, the spare wheel well insert 3 must not be removed. The installation position is indicated by an arrow pointing to the direction of travel. 130 Self-help, Vehicle Care Select neutral gear. Caution Drive slowly. Do not drive jerkily. Excessive tractive force can damage the vehicle. When the engine is not running, considerably more force is needed to brake and steer. To prevent the entry of exhaust fumes from the towing vehicle, switch on the air recirculation system 3 and close the windows. Screw in the towing eye anticlockwise as far as it will go until it stops in a horizontal position. Attach a tow rope 3 – or better still a tow rod 3 – to the eye. The towing eye must only be used for towing, not for recovering the vehicle. Switch on ignition to release steering column lock and to permit operation of brake lamps, horn and windscreen wipers. Contact a workshop. If the automatic clutch has been disengaged manually after a power failure on vehicles with Easytronic 3, towing is not permitted, 3 105. In this case, contact a workshop immediately. After towing, unscrew towing eye by rotating clockwise and insert and close the cap. Warning triangle ¨ 3 and First-aid kit + 3 Fasten the warning triangle and first-aid kit (cushion) to the flooring behind the seats with Velcro straps, as illustrated. Self-help, Vehicle Care Fasten the Velcro straps to the warning triangle and the first-aid kit (cushion) as illustrated. Spare wheel 3 Some vehicles are equipped with a tyre repair aerosol instead of a spare wheel 3 137. The spare wheel is stowed in the luggage compartment, held in place under a floor cover with a wing nut. Close retractable steel roof 3 36. Fold luggage compartment partition forwards 3 47. Pull the spare wheel forward and then upward out of the wheel well. 131 132 Self-help, Vehicle Care General information Depending on version, the spare wheel may be in the form of a temporary spare wheel 3. Refer to the notes on this page and 3 125, 3 176. On vehicles with alloy wheels 3, the spare wheel may have a steel rim. Use of a spare wheel together with winter tyres could alter driving characteristics. Have the defective tyre replaced as soon as possible. Use of a spare wheel that is smaller than the other wheels could alter driving characteristics. In many countries, it is only permitted as a temporary spare wheel. Have the defective tyre replaced as soon as possible. Notes on temporary spare wheel 3 z The use of the temporary spare wheel may affect the handling of the vehicle, particularly if winter tyres 3 are being used. The Electronic Stability Programme (ESP®Plus) 3 may switch itself off. Replace defective tyre as soon as possible, balance wheel and fit to vehicle. z Fit only one temporary spare wheel. z Do not drive faster than 50 mph (80 km/h). z Take bends slowly. z Do not use the temporary spare wheel for a lengthy period. z Replace temporary spare wheel with full specification wheel without delay. z Tyre chains are not permitted on the temporary spare wheel. If tyre chains have to be used after a front wheel puncture, fit temporary spare wheel to the rear axle and fit a rear wheel to the front axle. Check tyre pressure and correct if necessary 3 122, 3 176. z Read notes on temporary spare wheel on 3 125, 3 176. Notes on directional tyres 3 Fit directional tyres such that they roll in the direction of travel. The rolling direction is indicated by a symbol (e.g. an arrow) on the sidewall. The following applies to tyres fitted opposing the rolling direction: z Driving characteristics may be altered. Have the defective tyre replaced as soon as possible. z Do not drive faster than 50 mph (80 km/h). z Drive especially carefully in wet or snowy weather. Further notes on directional tyres 3 122. Self-help, Vehicle Care Changing wheels z Use the jack 3 only to change wheels. Some versions have tyre repair aerosol instead of a spare wheel 3 137. z If the ground on which the vehicle is standing is soft, a solid board (max. 1 cm thick) should be placed under the jack 3. Make the following preparations and observe the following information: z Park the vehicle on a level, firm and nonslippery surface. The front wheels must be in the straight-ahead position. z Close retractable steel roof 3 36. z Switch on the hazard warning lamps, apply the handbrake, engage first gear or reverse. Jack £ 3 and vehicle tools 3 The jack and the vehicle tools have been specially developed for your vehicle and must only be used on that vehicle. Only use jack for changing wheels. The jack and vehicle tools are located in a pouch or in a stowage compartment in the spare wheel well in the luggage compartment. For reasons of design, the spare wheel well insert 3 must not be removed. The installation position is indicated by an arrow pointing to the direction of travel. 133 z Erect warning triangle as required. Warning triangle 3 130. z Remove the spare wheel 3 3 131. z Never change more than one wheel at a time. z Block the wheel diagonally opposite the wheel to be changed by placing wedge blocks or equivalent in front and behind the wheel. z No people or animals may be in the vehicle when it is jacked-up. z Never crawl under a jacked-up vehicle. z Do not start the vehicle when it is raised on the jack. z Before screwing in the wheel bolts, clean them and lightly coat the cone of each wheel bolt with commercially available grease. Make sure that the bolt threads are not greased. 134 Self-help, Vehicle Care 1. Pull off the wheel trim with the hook 3. Vehicle tools 3 133. If the wheel trim has visible wheel bolts 3, the trim can remain on the wheel. The retaining washers 3 on the wheel bolts must not be removed. Alloy wheels 3: Prise off the wheel trim 3 with a screwdriver. Protect the rim by placing a soft cloth between the screwdriver and the alloy wheel. 2. Push the wheel bolt wrench 3 on as far as possible and slacken the wheel bolts half a turn. Self-help, Vehicle Care 3. The jacking points are marked on the bottom edge of the vehicle. 4. Set the jack 3 to the necessary height. Position the jack arm at the front or rear so that the jack claw (arrowed in illustration) spans the vertical base and engages in the recess in the base. Make sure it is securely positioned. 135 The edge of the jack base must be on the ground directly below the jacking point in a manner that prevents it from slipping. Raise vehicle by turning crank handle. If this edge of the jack base is no longer directly below the jacking point, carefully lower the vehicle immediately, reposition the jack and raise the vehicle again. 136 Self-help, Vehicle Care 5. Unscrew the wheel bolts. 10. Before refitting the wheel trim, clean the wheel around the retaining clips. Valve symbol 3 on back of wheel trim must point towards valve on wheel. If the wheel bolts have retaining washers 3, they must not be removed. 6. Change wheel. Notes on spare wheel 3 131. Notes on temporary spare wheel 3 132. Position and engage wheel trim. Alloy wheels 3: Align and refit wheel bolt caps 3. 11. Stow removed wheel with jack and warning triangle 3 130, 3 133. 12. Check the tyre pressure of the newly mounted wheel. 13. Have the wheel bolt tightening torque (110 Nm) checked. 7. Screw in the wheel bolts. Push the wheel bolt wrench 3 on as far as possible and tighten the wheel bolts slightly. 8. Lower vehicle. 9. Push the wheel bolt wrench 3 on as far as possible and tighten in a crosswise sequence. Tightening torque is 110 Nm. 14. Replace the faulty tyre on the wheel that was removed. Self-help, Vehicle Care The tyre repair aerosol is located in the luggage compartment in the spare wheel well. 1. Remove foreign bodies from the tyre and turn the wheel so that the tyre valve is horizontal, that is to say at the midline of the wheel. 2. Completely relieve tyre pressure by pressing the valve core inward with a screwdriver. Tyre repair aerosol 3 Minor damage to the tyre tread and sidewall, e.g. foreign bodies, can be remedied with the tyre repair aerosol. In the event of a flat tyre: z Park the vehicle on a level, firm and nonslippery surface. z Switch on the hazard warning lamps, apply the handbrake, engage first gear or reverse. z Erect warning triangle as required. Warning triangle 3 130. 3. Shake the aerosol can well. If temperatures are low, warm the can with your hands or with the air vents in the vehicle interior, with the engine running and the heating on 3 94. 4. Screw connecting piece on hose of aerosol to tyre valve. 137 5. Remove the seal. Hold the aerosol upright and depress the button until the aerosol has completely discharged. The tyre is then filled with sealant. 6. Unscrew the connector from the tyre valve. 7. Collapse the warning triangle and stow it behind the left seat. 8. Immediately drive 3 to 6 miles (5 to 10 km) at a speed of no more than 30 mph (50 km/h). This distributes the sealant throughout the tyre. 9. After first making sure there are no naked flames nearby, release the gas in the tyre as quickly as possible by pressing the valve core inward with a screwdriver. Fill the tyre with compressed air. 10. Check the tyre pressure at regular intervals. 11. Have the tyre repaired as soon as possible and inform the workshop that tyre repair aerosol was used. 138 Self-help, Vehicle Care The tyre repair aerosol allows for temporary use of the tyre; it merely allows for continued travel until the tyre can be changed. Fold the used tyre repair aerosol in a cloth and stow in the luggage compartment. The tyre repair aerosol can only be used once for repair and must then be replaced. Contact a workshop. The tyre repair aerosol can only be used on one tyre at a time. Follow national legislation when disposing of used tyre repair aerosol. Note 9 Warning Do not drive faster than 30 mph (50 km/h). Take bends slowly. Have the repaired tyre replaced as soon as possible. Steerability and driving behaviour may be impaired. The tyre repair aerosol is highly inflammable. Only stow the tyre repair aerosol in the luggage compartment. Follow the instructions on the tyre repair aerosol. Electrical system Fuses Data on the replacement fuse must match the data on the defective fuse. Before replacing a fuse, turn off the respective switch and the ignition. A defective fuse can be recognized by its melted wire. A new fuse should only be installed after the cause of the trouble has been rectified. To help in replacing fuses, there is a special fuse extractor in the fuse box 3. Self-help, Vehicle Care Fuse box The fuse box is located in the engine compartment next to the coolant expansion tank. Disengage cover of fuse box from lug and lift off. Place spare fuses at the point provided in the fuse box; next to this on the right is the fuse extractor for changing fuses. 139 Slot fuse extractor onto fuse and withdraw it. Always use fuses with the correct current rating. This is shown on each fuse, and is also indicated by the fuse colour and the plug-in location in the fuse box. 140 Self-help, Vehicle Care No. 5 6 7 8 9 10 11 12 Fuses and the most important circuits they protect Some circuits may be protected by several fuses. The illustrations on pages 140, 141 depict the fuse boxes of vehicles with engine Z 13 DT. Fuse boxes of other engines are depicted on pages 142, 143. No. 1 2 Circuit Central control unit Engine control unit No. 3 4 Circuit Instruments, information display, light switch, horn, hazard warning lamps, immobiliser – Circuit Electric window (left) – – Ignition switch, starter Injection system, fuel pump Horn Central control unit Information display, Infotainment system: engine Z 13 DT Self-help, Vehicle Care No. 13 14 15 16 17 18 141 Circuit Vauxhall alarm system Heated exterior mirrors Windscreen washer system Courtesy lamp Central control unit Heated rear window No. 19 20 21 22 23 Circuit Electric window (right) – – Central control unit, immobiliser Windscreen wipers No. 24 25 26 27 Circuit Infotainment system, Information display, Light switch, Courtesy lamp, Instruments, ESP®Plus Reversing lamps, cigarette lighter, accessory socket Seat heater (right) Seat heater (left) 142 Self-help, Vehicle Care No. 37 38 39 40 41 No. 28 29 30 31 32 Circuit ABS Retractable steel roof Engine control unit Air conditioning system ABS, airbag No. 33 34 35 36 Circuit Engine control Diesel filter heater Electric window, Infotainment system Dipped beam (left) Circuit Right dipped beam, headlamp range adjustment Tail lamp (left), parking lamp (left) Tail lamp (right), parking lamp (right) Brake lamps, cruise control Front fog lamps Self-help, Vehicle Care No. 42 43 44 45 46 47 48 Circuit Fog tail lamp Main beam (left) Main beam (right) Ventilation fan Engine control unit Retractable steel roof Starter No. 49 50 51 Circuit ESP®Plus ABS, ESP®Plus Petrol engine: Easytronic Diesel engine: Engine control unit No. 52 53 54 Circuit Radiator fan Radiator fan – 143 144 Self-help, Vehicle Care Bulb replacement Switch off the ignition and turn off the relevant switch or close the doors. Only hold a new bulb at the base! Do not touch the bulb glass with your bare hands. Replace the bulb, checking that the data on the base matches that of the defective bulb. When replacing bulbs in the front right headlamp, detach the air hose from the air filter. Halogen headlamp system dipped and main beam Headlamps have separate systems for dipped beam (inner bulbs) and main beam (outer bulbs). Dipped beam 1. Open bonnet and engage support. 2. Remove headlamp protective cover. Self-help, Vehicle Care Main beam Have bulbs changed by a workshop. Parking lamps Have bulbs changed by a workshop. 3. Detach plug connector from bulb. 4. Disengage spring wire clip from retaining lugs by moving it sideways and swivel it upward. 5. Remove bulb from reflector housing. 6. When fitting the new bulb, insert lugs in the reflector recesses. 7. Engage spring wire clip, attach plug connector onto bulb. 8. Place headlamp protective cover in position and close. 145 146 Self-help, Vehicle Care Side turn signal lamp Have bulbs changed by a workshop. Front fog lamps 3 Have bulbs changed by a workshop. Turn signal lamps Front turn signal lamps 1. Open bonnet and engage support. 2. Rotate bulb holder anticlockwise and disengage. 3. Remove bulb holder from reflector housing. 4. Push bulb into bulb holder slightly, rotate anticlockwise and remove. 5. Insert new bulb. 6. Engage bulb holder in reflector housing by rotating it clockwise. Self-help, Vehicle Care Tail lamps 1. Open the luggage compartment. 2. Disengage cover of retaining lugs and remove. 3. Hold bulb housing from the outside and unscrew both retaining nuts. 4. Detach bulb housing towards the rear. 5. Disengage and remove bulb holder from bulb housing by rotating bulb holder anticlockwise: 1 2 3 4 = = = = Reversing lamp Turn signal lamp Tail lamp/brake lamp Fog tail lamp (Country-specific version: fog tail lamp on one side only). 147 6. Push bulb into bulb holder slightly, rotate anticlockwise and remove. 7. Insert new bulb. 8. Engage bulb holder into bulb housing by rotating bulb holder clockwise. 9. Insert bulb housing in vehicle body and tighten retaining nuts by hand. 10. Fit cover. 148 Self-help, Vehicle Care Number plate lamp 1. Insert screwdriver vertically on righthand side of bulb housing, exert pressure towards the right and disengage spring. Remove the bulb housing downwards. 2. Rotate bulb holder anticlockwise and disengage. 3. Remove bulb from socket. 4. Insert new bulb. 5. Engage bulb holder by rotating clockwise in bulb housing. 6. Insert bulb housing in original position and engage. Self-help, Vehicle Care Courtesy lamp Front courtesy lamp 1. Lever the lens out of the housing at the points shown in the illustration. 2. Remove bulb from socket. 3. Insert new bulb. 4. Mount lens and engage in position. Luggage compartment lamp 1. Prise the lens out with a screwdriver. 2. Press bulb slightly towards spring clip and remove. 3. Insert new bulb. 4. Insert lens in aperture and engage in position. Instrument illumination, Information display illumination Have bulbs changed by a workshop. 149 150 Self-help, Vehicle Care Vehicle care When caring for your vehicle, observe all national environmental regulations, particularly when washing it. Regular, thorough care helps to improve the appearance of your vehicle and maintain its value over the years. It is also a prerequisite for warranty claims for any paint or corrosion damage. The following pages contain tips for vehicle care which, if used properly, will help combat the unavoidable damaging effects of the environment. Washing The paintwork of your vehicle is exposed to environmental influences. Wash and wax your vehicle regularly. When using automatic car washes, select a programme that includes waxing. Bird droppings, dead insects, resin, pollen and the like should be cleaned off immediately, as they contain aggressive constituents which can cause paint damage. When using a car wash, follow the instructions of the car wash manufacturer. Switch off windscreen wipers. Unscrew antenna rod 3. If you wash your vehicle by hand, make sure that the insides of the wings are also thoroughly rinsed out. Clean edges and folds on opened doors and flaps as well as the areas they cover. Wheels and tyres Do not use high-pressure jet cleaners. Thoroughly rinse off and leather-off the vehicle. Rinse leather frequently. Use separate leathers for paint and window surfaces: remnants of wax on the windows will impair vision. Clean wheels with a pH-neutral wheel cleaner. Polishing and waxing Wax the vehicle regularly (at the latest when water no longer forms beads on the paintwork). Otherwise, the paintwork will dry out. Polishing is necessary only if the paint has become dull or if solid deposits have become attached to it. Paintwork polish with silicone forms a protective film, making waxing unnecessary. Plastic body parts should not be treated with wax and polish. Wheels are painted and can be treated with the same agents as the body. Paintwork damage Rectify minor paintwork damage with a touch-up pen before rust forms. Have more extensive damage or rust areas repaired by a workshop. Exterior lamps Headlamp and other lamp covers are made of plastic. Do not use any abrasive agents, do not use an ice scraper, and do not clean them dry. Plastic and rubber parts Plastic and rubber parts can be cleaned with the same cleaner as used to clean the body. Use interior cleaner if necessary. Do not use any other agent. Avoid solvents and petrol in particular. Do not use high-pressure jet cleaners. Self-help, Vehicle Care Interior and upholstery Only clean the vehicle interior, including the instrument panel facia and panelling, with a dry cloth or interior cleaner. The instrument panel should only be cleaned using a soft damp cloth. Clean fabric upholstery with a vacuum cleaner and brush. Remove stains with an upholstery cleaner. Clean seat belts with lukewarm water or interior cleaner. Caution Close Velcro fasteners as open Velcro fasteners on clothing could damage seat upholstery. Windows and windscreen wiper blades Use a soft lint-free cloth or chamois leather together with window cleaner and insect remover. When cleaning the rear window, make sure the heating element inside the window is not damaged. For mechanical removal of ice, use a sharpedged ice scraper. Press the scraper firmly against the glass so that no dirt can get under it and scratch the glass. Clean smearing wiper blades with a soft cloth and window cleaner. 151 Locks The locks are lubricated at the factory using a high quality lock cylinder grease. Use de-icing agent only where absolutely necessary, as this removes grease and impairs lock function. After using de-icing agent, have the locks regreased by a workshop. Underbody Some areas of the vehicle underbody have a PVC undercoating while other critical areas have a durable protective wax coating. Engine compartment Clean painted surfaces in the engine compartment like any other painted surface. Bitumen/rubber materials could damage the PVC coating. Have underbody work carried out by a workshop. It is advisable to wash the engine compartment before and after winter and preserve it with wax. Before engine washing, cover alternator and brake fluid reservoir with plastic sheeting. When washing the engine with a steam-jet cleaner, do not direct the steam jet at components of the Anti-lock Braking System 3 , the automatic air conditioning system 3 or the belt drive and its components. After an engine wash, have all engine room components preserved thoroughly by a workshop using protective wax. Do not use high-pressure jet cleaners. After the underbody is washed, check the underbody and have more protective wax applied if necessary. Before and after winter, wash the underbody and have the protective wax coating checked. Retractable steel roof Coat all seals, such as on the roof and the windscreen frame, with silicone oil from time to time. A constant close contact between the fine rubber lips and the sealing faces ensures a tight fit and low closing forces. Do not use high-pressure jet cleaners. 152 Service and Maintenance Service and Maintenance Scheduled maintenance The service intervals apply to normal conditions of use. For extreme operating conditions 3 156. Service interval display 3 158. Service intervals Every 20,000 miles (30,000 km) or annually, whichever occurs first. Scheduled maintenance ..................... Additional service work....................... Recommended fluids and lubricants . Inspection system ................................ Vauxhall genuine parts and accessories......................................... Performing work .................................. Engine oil .............................................. Diesel fuel filter .................................... Coolant ................................................. Brake fluid ............................................ Windscreen wiper replacement .......... Windscreen washer system................. Battery .................................................. Protecting electronic components ..... Laying the vehicle up for a long period of time .................................... Putting the vehicle back into service . 152 156 156 158 159 159 160 162 162 164 165 165 165 166 166 167 Confirmation Service confirmation is given in the fields provided in the Service and Warranty Booklet. The date and mileage/kilometre reading are given with the stamp and signature of the servicing garage. Ensure that the Service and Warranty Booklet is correctly completed, as an uninterrupted service record is crucial in the event of warranty claims or complaints, and is also an advantage when reselling the vehicle. Service and Maintenance Service Plan Service work after years 1) miles (x1000) 1) km (x1000)1) Visually inspect control systems, lighting and signalling systems and airbag, test steering and ignition lock 1 20 30 2 40 60 3 60 90 4 90 120 5 120 150 x x x x x Remote control: replace batteries (check second key). Every 2 years Windscreen wipers, windscreen washer system, headlamp washer system, check and correct x x x x x Check and correct coolant level and anti-freeze (bright orange)2), note coolant anti-freeze protection temperature in Service and Warranty Booklet (confirmation fields) x x x x x Test fluid-carrying hoses for leaks and firm attachment x x x x x Check and correct brake fluid level 2) x x x x x Vehicle system check with TECH 2 x x x x x x x if the air conditioning system has an odour By agreement with customer / Vauxhall Authorised Repairer Replace air filter insert Every 4 years / 40,000 miles / 60,000 km Replace spark plugs Every 4 years / 40,000 miles / 60,000 km Inspect ribbed V-belts 1) 2) x x ⊕o If air is very dirty, has a high dust or sand content or high pollen level, ⊕ x Test battery terminals for firm seat and battery eye Replace pollen filter or active charcoal filter ⊕ 153 Replace ribbed V-belts Z 13 DT x x Every 10 years / 120,000 miles / 150,000 km Whichever occurs first. In the case of excessive loss / leakage, additional work upon agreement with customer. ⊕ Additional work. o Under extreme operating conditions and if necessary for country-specific conditions, the intervals are shortened. 154 Service and Maintenance Service work ⊕ after years 1) miles (x1000) 1) km (x1000)1) Replace toothed belts and tensioning roller Z 18 XE Change engine oil and filter ⊕o Drain water from fuel filter, diesel (for high residual humidity and/or lower quality fuel) 1 20 30 2 40 60 3 60 90 4 90 120 Every 6 years / 60,000 miles / 90,000 km x x x x x x x x x x Replace fuel filter and drain out water, diesel (quality EN 590) Z 13 DT x x Check handbrake and adjust (wheel unloaded); inspect wheel mounting and suspension front and rear, brake lines, brake hoses, fuel lines and exhaust system x x Check external bodywork / underfloor corrosion protection, note damage in Service and Warranty Booklet 5 120 150 x ⊕o Inspect front and rear brakes2) x x x x x x Annual Service if the annual driving distance is over 12,000 miles (20,000 km) Inspect engine, transmission (MT, Easytronic), Air conditioning compressor for leaks2) ⊕o Remove, clean and inspect brake drums 1) 2) x x x x x Every 4 years / 40,000 miles / 60,000 km Whichever occurs first. In the case of excessive loss / leakage, additional work upon agreement with customer. ⊕ Additional work. o Under extreme operating conditions and if necessary for country-specific conditions, the intervals are shortened. Service and Maintenance Service work ⊕ after years 1) miles (x1000) 1) km (x1000)1) 155 1 20 30 2 40 60 3 60 90 4 90 120 5 120 150 Inspect gaiters on steering, track rods, final drive x x x x x Check track rod ends and ball joints x x x x x Change brake and clutch fluid (Easytronic) Every 2 years Release wheel fixings and tighten to torque 110 Nm Lightly grease or oil wheel bolt cones when fitting x Check tyre condition. Check and correct tyre pressure (including spare wheel) x For tyre repair aerosol, check fill level and expiry date every 3 years ⊕ Annual Service if the annual driving distance is over 12,000 miles (20,000 km) Inspect first-aid kit (presence in stowage compartment, completeness and expiry date), lashing eyes and warning triangle Check and correct headlamp adjustment (including auxiliary lamps) x x Lubricate door hinges, check straps, lock cylinders, lock brackets, bonnet closure, tailgate hinges x x ⊕o Clean and lubricate folding roof in dusty countries (by agreement with customer/Vauxhall Authorised Repairer) Test drive, final check (steering and ignition lock, instruments and control indicators, entire braking system, steering, air conditioning, engine, bodywork and chassis), reset service interval display with TECH 2 1) Every 2 years x x x x x x x x x x Whichever occurs first. ⊕ Additional work. o Under extreme operating conditions and if necessary for country-specific conditions, the intervals are shortened. 156 Service and Maintenance Additional service work Additional work ⊕ Additional work is work which is not necessary on every service, but may be performed at the same time as a regular service. The time allowances for such work are not included in the scope of the regular service, and are invoiced separately. It is however more economic to perform this work as part of a scheduled service than as a separate task. Extreme operating conditions o Conditions are considered extreme if one or more of the following circumstances occur frequently: z cold starts, z stop and go, z caravan/trailer towing, z gradients and/or high altitudes, z poor road conditions, z sand and dust, z extreme temperature fluctuations. Police vehicles, taxis and driving school vehicles are also classed as undergoing extreme operating conditions. Under extreme operating conditions, it may be necessary to perform certain service work more frequently than at the scheduled intervals. We recommend obtaining technical advice on the service requirements for your vehicle depending on the particular conditions of use. Recommended fluids and lubricants Only use products which have been tested and approved. Damage caused by the use of operating materials which are not approved is not covered by the warranty. 9 Warning Operating materials are hazardous and require corresponding care when handling. If swallowed, consult a doctor immediately. Do not inhale fumes and avoid skin contact. Keep out of the reach of children. Operating materials must not pollute waste water, surface water, ground water or soil. Dispose of empty containers correctly. Always remember that operating materials are harmful to health. Service and Maintenance Engine oil Engine oil is characterised by its quality and viscosity. When selecting an engine oil to use, quality is more important than viscosity. Top up engine oil Oils from different manufacturers and makes can be mixed as long as the engine oil criteria (quality and viscosity) are observed. Engine oil for Service Plan GM-LL-A-025: Petrol engines GM-LL-B-025: Diesel engines Not every engine oil available on the market meets the quality requirements, so always check whether the specifications and classifications required are shown on the container. GM LL A or B 025 General Motors Europe Longlife Engine oil grade Validity index Vauxhall engine oil complies with classifications GM-LL-A-025 and GM-LL-B-025 and is therefore suitable for both petrol and diesel engines. If engine oil of the required quality is not available, no more than 1 litre of category ACEA A3/B4 or A3/B3 may be used (only twice between two oil changes). The viscosity must comply with requirements. The use of engine oil category ACEA A1/B1 and A5/B5 is expressly prohibited as it can cause long-term damage to the engine under certain circumstances. 157 Engine oil additives The use of engine oil additives can cause damage and invalidate the warranty. Engine oil viscosity Only use engine oil viscosities 0W-30, 0W-40, 5W-30 or 5W-40. The SAE viscosity class indicates the flow capacity of the oil: In cold weather, the oil is more viscous than when warm. Multigrade oil is indicated by two figures. The first figure followed by W indicates the viscosity at low temperature, and the second figure the viscosity at high temperature. 158 Service and Maintenance The service interval display takes account of off-the-road periods during which the battery is disconnected. Flexible service interval 3 The length of the service intervals is based on several parameters stemming from usage. For this reason, various engine-specific data is continually gathered and is used to calculate the remaining distance until the next service. Inspection system In order to ensure economical and safe vehicle operation and to maintain the value of your vehicle, it is of vital importance that all maintenance work is carried out at the proper intervals as specified. Fixed service interval When service is due, InSP appears in the odometer display for approx. 10 seconds when the ignition is switched on. Have the next service performed by a workshop within one week or 300 miles (500 km), whichever occurs first. If the remaining distance is less than 1000 miles (1500 km), InSP is displayed with a remaining distance of 600 miles (1000 km) when the ignition is switched on and off. If less than 600 miles (1000 km) remains, InSP is displayed for several seconds. Have the next service performed by a workshop within one week or 300 miles (500 km), whichever occurs first. Display of remaining distance: 1. Switch off ignition. 2. Briefly press the trip odometer reset button. The odometer reading is shown. 3. Press and hold the reset button for approx. 2 seconds. InSP and the remaining distance are displayed. Further information on maintenance and the inspection system can be found in the Service and Warranty Booklet, which is in the glove compartment. Have service work and repairs to the bodywork and components performed properly by a workshop in accordance with Vauxhall motors’ recommendations, using Vauxhall genuine parts and accessories. We recommend your Vauxhall Authorised Repairer, who has excellent knowledge of Vauxhall vehicles and is in possession of the necessary tools and current service instructions from Vauxhall. To avoid invalidating the warranty, use of a Vauxhall Authorised Repairer is recommended in particular during the warranty period. For further information see the Service and Warranty Booklet. Separate anti-corrosion service Carry out after the intervals specified in the Service and Warranty Booklet. Service and Maintenance 159 Vauxhall genuine parts and accessories We recommend that you use "Vauxhall genuine parts and accessories" and conversion parts released expressly for your vehicle type. These parts have undergone special tests to establish their reliability, safety and specific suitability for Vauxhall vehicles. Despite continuous market monitoring, we cannot assess or guarantee these attributes for other products, even if they have been granted approval by the relevant authorities or in some other form. "Vauxhall genuine parts and accessories" and conversion parts approved by Vauxhall can be obtained from your Vauxhall Authorised Repairer, who can provide expert advice on permitted technical changes and ensure correct installation. Performing work To avoid injury from moving parts and cables conducting ignition voltage, only carry out engine compartment checks (e.g. checking brake fluid or engine oil level) when the ignition is switched off. 9 Warning Only perform engine compartment checks when the ignition is off. The cooling fan may start operating even if the ignition is off. 9 Warning The ignition system 3 and Xenon headlamps 3 use extremely high voltage. Do not touch. To aid identification, the caps used when topping up engine oil, coolant and washer fluid as well as the oil dipstick are coloured yellow. 160 Service and Maintenance Engine oil For vehicles with engine oil level check 3, the engine oil level is checked automatically 3 70. We recommend checking the engine oil level before starting a long journey. Caution Important: It is the owner’s responsibility to maintain the correct level of an appropriate quality oil in the engine. Check with the vehicle on a level surface. The engine must be at operating temperature and switched off for at least 5 minutes. Pull out the dipstick, wipe it clean (use a fibre-free material), insert it to the stop on the handle, pull out and read the engine oil level. Insert oil dipstick up to the stop surface on the handle, and twist half a turn. Different dipsticks are used depending on engine variant. When the engine oil level has dropped to the MIN mark, top up engine oil. Caution Do not allow the engine oil to drop below the minimum level! Service and Maintenance Top up to between the MIN and MAX marks 3 178. Fit the cap on straight and tighten it. We recommend that you use the same engine oil as was used the last time it was topped up. The engine oil level must not exceed the MAX mark on the dipstick. Caution If there is too much engine oil, the excess must be drained or suctioned out. 161 162 Service and Maintenance Diesel fuel filter Coolant On each engine oil change, have the fuel filter checked for any water residue by a workshop. The coolant provides anti-freeze protection down to approx. -28 °C. Caution Illumination of control indicator A in the instrument cluster indicates water in the diesel fuel filter. Have fuel filter checked at shorter intervals if the vehicle is subjected to extreme operating conditions such as high humidity (primarily in coastal areas), extremely high or low outside temperatures and substantially varying daytime and night-time temperatures. Only use approved anti-freeze. Coolant additives for additional corrosion protection and to seal minor leaks can cause function problems. No liability is accepted for damage caused by the use of coolant additives. . 9 Warning Anti-freeze is a danger to health; it must therefore be kept in the original container and out of the reach of children. Anti-freeze and corrosion protection Before the start of winter, have a workshop check the anti-freeze protection. The anti-freeze level must guarantee protection down to approx. -28 °C. Insufficient anti-freeze will reduce the frost protection level and the corrosion protection. If necessary, add anti-freeze. If coolant loss is topped up with water, have concentration checked and add anti-freeze if necessary. Service and Maintenance Top up with anti-freeze. If no anti-freeze is available, fill with clean tap water or distilled water. Have the anti-freeze concentration checked. Have the cause of coolant loss rectified by a workshop. Caution Too low a coolant level can cause engine damage. Fit the cap on straight and tighten it. Coolant level In a closed cooling system, there is hardly any loss. If the cooling system is cold, the coolant level should be above the KALT/COLD mark. Top up if the level is low. 9 Warning Allow the engine to cool before opening the cap. Carefully open the cap, relieving the pressure slowly. 163 Brakes A screeching noise indicates that the brake lining is at its minimum thickness. Continued driving is possible. Have the brake lining replaced as soon as possible. Once new brake linings are fitted, do not brake unnecessarily hard for the first 125 miles (200 km). 164 Service and Maintenance Brake fluid change Brake fluid is hygroscopic, i.e. it absorbs water. If the brakes become hot, such as when driving on long downhill stretches, vapour bubbles can occur in the water, which can have an extremely adverse effect on braking power (depending on the proportion of water). Therefore observe the specified change intervals. 9 Warning Brake fluid Brake fluid level 9 Warning Brake fluid is poisonous and corrosive. Do not allow it to come into contact with eyes, skin, fabrics or painted surfaces. Open the cover of the brake fluid reservoir upwards, removing the sealing rubber on the front edge. The brake fluid must be between the MIN and the MAX marks. Absolute cleanliness is important when topping up, since contamination in the brake fluid can cause brake system malfunctions. Only use approved high performance brake fluid. Only use DOT4 brake fluid. After correcting the brake fluid level, have a workshop eliminate the cause of the brake fluid loss. Have the brake fluid changed by a workshop. Observe the legal requirements for disposal of brake fluid to protect the environment and your health. Service and Maintenance 165 Windscreen wiper replacement Windscreen washer system Battery Lift wiper arm. Move release lever and detach wiper blade. The washer bottle for the windscreen washer system is in engine compartment on the left-hand side. The vehicle battery is maintenance-free. Fill with clean water mixed with cleaner and anti-freeze. Make sure there is sufficient anti-freeze protection. When closing the reservoir, press the lid firmly over the beaded edge all the way round. Batteries do not belong in household waste. They must be disposed of at an appropriate recycling collection point. Retrofitting of electrical or electronic accessories can discharge or add extra load to the battery. Take advice on the technical possibilities, e.g. use of a more powerful battery. 166 Service and Maintenance Laying up the vehicle for more than 4 weeks can lead to battery discharge. Disconnect the negative terminal of the vehicle battery. Ensure the ignition is switched off before connecting or disconnecting the vehicle battery. Note The Vauxhall alarm system 3 siren must be deactivated as follows: switch the ignition on then off, disconnect the vehicle’s battery within 15 seconds. Protecting electronic components In order to prevent faults in electronic components in the electrical system, never connect or disconnect battery with engine running or ignition switched on. Never start engine with battery disconnected, e.g. when starting using jump leads. To avoid damaging the vehicle, do not make any modifications to the electrical system, e.g. connecting additional consumers or tampering with electronic control units (chip tuning). 9 Warning Electronic ignition systems generate very high voltages. Do not touch the ignition system; high voltage can be fatal. Laying the vehicle up for a long period of time If the vehicle is to be laid up for several months, the following work should be undertaken to prevent damage. z Wash and wax the vehicle 3 150. z Have the wax in the engine compartment and underbody checked. z Clean and preserve rubber seals. z Change engine oil. z Check anti-freeze and corrosion protection 3 162. z Check coolant level, if necessary top up with anti-freeze3 163. z Drain the windscreen washer system. z Increase tyre pressure to the value specified for full load 3 122, 3 176. Service and Maintenance z Park vehicle in dry and well ventilated place. With manual transmission select first gear or reverse gear, and with Easytronic 3 move selector lever to centre position before switching ignition off. Use wedges or the like to prevent vehicle from rolling. Putting the vehicle back into service z Do not apply handbrake. z Check tyre pressure 3 122, 3 176. z Disconnect the clamp from the negative terminal of the vehicle battery. z Top up windscreen washer system 3 165. Perform the following work before recommissioning the vehicle: z Connect the clamp to the negative terminal of the vehicle battery. z Check engine oil level 3 160. z Check coolant level 3 163. z Fit the number plate if necessary. 167 168 Technical Data Technical Data Vehicle data......................................... Engine data.......................................... Performance......................................... Fuel consumption, CO2 emissions ...... Weights, payload and roof load ........ Tyres ..................................................... Capacities ............................................ Dimensions ........................................... 168 170 171 172 174 176 178 179 Vehicle data The technical data is determined in accordance with European Community standards. We reserve the right to make modifications. Specifications in the vehicle documents always have priority over those given in this manual. The identification plate is located on the right MacPherson strut tower in the engine compartment. In other versions, the identification plate is attached to the right-hand front door frame. Technical Data Information on identification plate: 1 2 3 4 5 6 7 8 Manufacturer Type approval number Vehicle identification number Gross vehicle weight rating Permissible gross train weight Maximum permissible front axle load Maximum permissible rear axle load Vehicle-specific or country-specific data The vehicle identification number is stamped on the identification plate and on the right side of the floor of the vehicle under a cover between the front door and the seat. On some versions, the VIN can also be found on the instrument panel. Engine identifier and engine number: Marked on left-hand side of engine in engine block. 169 170 Technical Data Engine data Sales designation Engine identifier code 1.4 TWINPORT Z 14 XEP 1.8 Z 18 XE 1.3 CDTI Z 13 DT 4 4 4 Piston displacement [cm ] 1364 1796 1248 Engine power [kW] at rpm 66 5600 92 6000 51 4000 Torque [Nm] at rpm 125 4000 165 4600 170 1750 to 2500 Petrol Petrol Petrol 95 3) 98 3) 91 3)4) 95 3) 98 3) 91 3)4) – – – Cetane number (CN)2) – – 49 (D)5) Max. permissible engine speed, continuous operation (rpm) approx. 6200 6500 5100 to 5300 Oil consumption [l/1000 km] 0.6 0.6 0.6 Number of cylinders 3 Type of fuel1) Octane rating RON recommended possible possible 1) 2) 3) 4) 5) 2) Standard quality fuel, e.g. unleaded DIN EN 228, diesel DIN EN 590. Standard quality fuels: D = Diesel; bold type: recommended fuel. Knock control system automatically adjusts ignition timing according to type of fuel used (octane number). Slight reduction in engine output and torque if 91 RON is used. A lower value is possible with winter diesel fuels. Technical Data Performance Z 14 XEP Z 18 XE Z 13 DT 112/180 111/178 127/204 – 104/167 – 1) Maximum speed [mph / km/h] Sports transmission Easytronic 1) The maximum speed is achievable with a maximum of half payload. Optional equipment may reduce the specified maximum speed of the vehicle. 171 172 Technical Data Fuel consumption, CO2 emissions Directive 80/1268/EEC (last amended by 2004/3/EC) has been applicable to the measurement of fuel consumption since 1996. The directive is oriented to actual driving practices: Urban driving is rated at approx. 1/3 and extra-urban driving at approx. 2/3 (urban and extra-urban consumption). The figures given must not be taken as a guarantee for the actual fuel consumption of a particular vehicle. Cold starts and acceleration phases are also taken into consideration. The calculation of fuel consumption as specified by directive 2004/3/EC takes account of the vehicle’s kerb weight, ascertained in accordance with the aforementioned regulation. Optional extras may result in slightly higher fuel consumption and CO2 emission levels than those quoted. The specification of CO2 emission is also a constituent of the directive. All values are based on the EU base model with standard equipment. To convert l/100 km into mpg, divide 282 by number of litres/100 km. Saving fuel, protecting the environment 3 108 Technical Data Fuel consumption, CO2 emissions Sports transmission/Easytronic Fuel consumption urban [l/100 km] rural [l/100 km] total [l/100 km] CO2 [g/km] Z 14 XEP Z 18 XE Z 13 DT 8.1/ 8.0 5.0/ 4.9 6.1/ 6.0 146/144 10.4/– 5.8/– 7.5/– 179/– 5.8/– 3.9/– 4.6/– 124/– 173 174 Technical Data Weights, payload and roof load The payload is the difference between the permitted gross vehicle weight (see identification plate 3 168) and the EC kerb weight. Optional equipment and accessories increase the kerb weight, which means that the payload will also change slightly. Note weight ranges in the vehicle documents and on the rating plate. The combined total of front and rear axle loads must not exceed the permissible gross vehicle weight. For example, if the front axle is bearing its maximum permissible load, the rear axle can only bear a load that is equal to the gross vehicle weight minus the front axle load. Roof loads are not permitted. Driving hints 3 106. Technical Data Kerb weight1) Tigra retractable steel roof Engine Sport transmission Easytronic without air conditioning [kg] Z 14 XEP 1235 1235 Z 18 XE 1265 – Z 13 DT 1278 – Z 14 XEP 1260 1260 Z 18 XE 1290 – Z 13 DT 1303 – Z 14 XEP 1305 1305 Z 18 XE 1335 – Z 13 DT 1348 – with air conditioning [kg] with maximum equipment [kg] 1) According to EC Directive 70/156/EC, including assumed weights for driver (68 kg), luggage (7 kg) and all fluids (tank 90% full). 175 176 Technical Data Tyres Winter tyres 3 Wheels Restrictions Not all tyres available on the market currently meet the structural requirements. We recommend that you consult a Vauxhall Authorised Repairer concerning suitable tyre makes. Tyres of size 185/60 R 15, 205/50 R 16 and 205/45 R 17 must not be used as winter tyres. Wheel bolt tightening torque: 110 Nm. If you use winter tyres 3, the spare wheel may still be fitted with a summer tyre. If you use the spare wheel the vehicle’s handling may be altered. Obtain a replacement for the faulty tyre as soon as possible, and have the wheel balanced and fitted to the vehicle. Depending on design, the spare wheel is designed as a temporary spare wheel 3. When using the spare wheel, the driving characteristics may be modified. Replace the faulty tyre as soon as possible, balance the wheel and refit to vehicle. Follow the notes on this page and 3 125, 3 131. Further information 3 121. On vehicles with alloy wheels 3, the spare wheel may have a steel rim. These tyres have undergone special tests to establish their reliability, safety and specific suitability for Vauxhall vehicles. Despite continuous market monitoring, we are unable to assess these attributes for other tyres, even if they have been granted approval by the relevant authorities or in some other form. Further information 3 121. Tyre chains 3 Tyre chains are only permitted on the front wheels. Tyre chains must not be used on the temporary spare wheel 3. Always use fine mesh chains that add no more than 10 mm to the tyre tread and the inboard sides (including chain lock). Tyre chains are not permitted on tyres of size 185/60 R 15, 205/50 R 16 or 205/45 R 17. Further information 3 121. Spare wheel 3 The spare wheel may be fitted with a smaller tyre1) and smaller wheel than the wheels fitted to the vehicle. Tyre pressure2) The specified tyre pressures are valid for cold tyres. Increased tyre pressure resulting from extensive driving should not be reduced. The pressures specified on the next page apply to both summer and winter tyres. Further information 3 121 to 3 125. 1) 2) Country-specific version: In some countries, the spare wheel may only be used as a temporary spare wheel. 1 bar corresponds to 100 kPa / 14.5 psi. Technical Data Tyre pressure Tyre pressure for load with one person and light luggage Tyre pressure for full load Tyres Front [psi/bar] Rear [psi/bar] Front [psi/bar] Rear [psi/bar] Z 14 XEP, Z 18 XE, Z 13 DT 185/55 R 15 36/2.5 36/2.5 36/2.5 36/2.5 185/60 R 15, 205/50 R 16, 205/45 R 17 33/2.3 30/2.1 33/2.3 30/2.1 Spare wheel 3 185/55 R 15 36/2.5 177 178 Technical Data Capacities Engine oil Engine Z 14 XEP Z 18 XE Z 13 DT Inc. Filter [litres] 3.5 4.25 3.2 Between MIN and MAX [litres] 1.0 1.0 1.0 45 45 45 Fuel tank Petrol/diesel, nominal capacity [litres] Technical Data Dimensions Tigra Length [mm] 3921 Width without exterior mirrors [mm] 1684 Width with two exterior mirrors [mm] 1905 Height [mm] 1376 Wheelbase [mm] 2491 Turning circle diameter [m] 11.00 179 180 Index Index A ABS (Anti-lock Braking System) ........... 120 Accessories................................. 53, 62, 130 Accessory socket ..................................... 63 Air conditioning system .......................... 96 Air intake.................................................. 99 Air recirculation system........................... 97 Air vents ................................................... 93 Airbags..................................................... 54 Alarm........................................................ 31 Alarm system ........................................... 29 Alternator................................................. 69 Antenna ........................................... 90, 150 Anti-corrosion service............................ 158 Anti-freeze ............................................. 162 Anti-freeze protection................... 162, 165 Anti-knock quality of fuel Octane number.................................. 170 Anti-theft locking system ........................ 24 Anti-theft protection ............................... 14 Aquaplaning.......................................... 124 Ashtray..................................................... 64 B Battery............................................ 107, 165 Interruption of power supply 25, 34, 105 Battery discharge protection ................. 89 Before starting off ................................... 12 Belt tensioners ......................................... 50 Bleeding, diesel fuel system.................. 126 Bonnet .................................................... 126 Boot, see Luggage compartment.... 26, 47 Brake assist ............................................ 121 Brake system ......................................... Brakes ABS ..................................................... Brake assist ........................................ Brake servo unit................................. Footbrake........................................... Handbrake......................................... Bulb replacement .................................. Bulbs....................................................... 119 120 121 106 121 121 144 144 C Capacities .............................................. 178 Car Pass ................................................... 20 Care ........................................................ 150 Catalytic converter........................ 112, 114 Central locking system...................... 22, 23 Changing the remote control battery ... 23 Changing tyre/wheel type .................... 121 Changing wheels................................... 133 Chassis number, see Vehicle identification number ............ 169 Child restraint system ............................. 53 Cigarette lighter ...................................... 63 Climate control ........................................ 92 Clutch operation.................................... 105 CO2 emissions........................................ 172 Coin holder .............................................. 65 Cold start ............................................... 107 Contrast ................................................... 80 Control indicators................................ 8, 66 Coolant .................................................. 162 Coolant level.......................................... 163 Coolant temperature display ................. 72 Coolant thermometer ............................. 72 Index Correcting time ........................................ 79 Courtesy lamp.......................................... 89 Courtesy lamps Bulb replacement............................... 149 Cruise control ......................................... 116 D Dashboard, see Instrument panel............ 6 Data.................................................. 20, 168 Date .......................................................... 76 Daytime running lamps........................... 86 Decommissioning .................................. 166 Demisting and defrosting Windows ............................................... 96 With the air conditioning system........ 98 Diesel fuel filter ...................................... 162 Diesel fuel system .......................... 126, 162 Dimensions ............................................. 179 Dipped beam ....................................... 9, 86 Bulb replacement............................... 144 Display...................................................... 74 Display mode ........................................... 80 Door locks......................................... 20, 151 Driving abroad....................................... 110 Headlamps........................................... 89 Driving hints ........................................... 106 181 E F Easytronic......................................... 12, 100 Driving programmes ......................... 102 Fault.................................................... 104 Interruption of power supply ............ 105 Kickdown.................................... 103, 104 Selector lever................................ 12, 101 Winter programme ............................ 103 Economical driving ................................ 108 Electric power-assisted steering ..... 70, 106 Electric windows ...................................... 32 Electrical system ............................ 138, 166 Electronic components.......................... 166 Electronic immobiliser ............................. 21 Electronic Stability Programme ............ 114 Engine code ........................................... 170 Engine control indicator........................ 113 Engine oil................................................ 157 Additives ............................................ 157 Topping up......................................... 157 Viscosity.............................................. 157 Engine oil consumption................. 106, 170 Engine oil level ......................................... 70 Engine oil pressure .................................. 68 Engine speed ......................................... 107 Engine wash........................................... 151 Environmental protection ..................... 150 EPS (Electric Power-assisted Steering) ... 70 ESP (Electronic Stability Programme) .. 114 Exhaust control indicator...................... 113 Exhaust gases........................................ 114 Exhaust system ...................................... 106 Exterior mirrors ............................ 31, 32, 34 Fan ..................................................... 92, 94 Fault ......................................................... 34 Electric windows .................................. 34 Filling station Capacities .......................................... 178 Engine oil level ................................... 160 Fuel ............................................. 110, 170 Opening the bonnet.......................... 126 Tyre pressure ............................. 109, 176 Vehicle data............................... 168, 169 Windscreen washer system .............. 165 First-aid kit (cushion) ............................ 130 Flat tyre.......................................... 133, 137 Fog tail lamp ........................................... 87 Bulb replacement .............................. 147 Foot brake ..................................... 119, 121 Front fog lamps....................................... 87 Bulb replacement .............................. 146 Front passenger airbag .......................... 54 Fuel................................................. 110, 170 Fuel consumption.................. 108, 110, 171 Fuel filter ................................................ 162 Fuel gauge............................................... 73 Fuel level .................................................. 73 Fuel system, diesel ................................ 126 Fuses .............................................. 138, 139 182 Index G Gears ................................................ 12, 105 Generator, see Alternator ....................... 69 Genuine parts and accessories ............ 159 Glove compartment ................................ 65 Graphical information display................ 74 Gross vehicle weight.............................. 174 H Halogen headlamp system .................. 144 Driving abroad..................................... 89 Handbrake ................................. 13, 14, 121 Hazard warning lamps ..................... 10, 88 Head restraints .................................. 46, 47 Headlamp flash ................................... 9, 87 Headlamp range adjustment................. 88 Headlamps.......................................... 9, 86 Changing bulbs.................................. 144 Daytime running lamps....................... 86 Driving abroad..................................... 89 Front fog lamps ................................... 87 Reversing lamps................................... 87 Warning device .................................... 84 Heated exterior mirrors............... 11, 32, 34 Heated rear window.................... 11, 32, 34 Heated seats............................................ 46 Heating............................................... 92, 95 Seats ..................................................... 46 With the air conditioning system........ 92 Height adjustment Steering wheel........................................ 5 High-pressure cleaners ......................... 151 Horn .......................................................... 10 I Identification plate ........................ 168, 169 Idling....................................................... 105 Ignition switch.......................................... 21 Ignition system............................... 159, 166 Immobiliser............................................... 21 Information display ................................. 74 Infotainment system ............................... 91 Instrument display................................... 72 Instrument illumination ........................... 89 Bulb replacement .............................. 149 Instrument panel ....................................... 6 Instruments .................................. 13, 66, 72 Interior mirror....................................... 5, 32 Interruption of power supply .................. 83 Easytronic........................................... 105 Electronic Stability Programme ........ 115 J Jack................................................. 133, 135 Jump leads............................................. 127 K Keys ...................................................... 2, 20 Extending ............................................. 20 Ignition lock.......................................... 13 Locking doors ................................ 22, 23 Remove................................................. 14 Starting................................................. 13 L Language selection ................................ 79 Light switch................................................. 9 Lighting ................................................ 9, 86 Driving abroad .................................... 89 Loading.................................................. 174 Lock cylinders .......................................... 20 Locking doors ................................ 2, 22, 23 Locking from the inside .......................... 24 Locks ...................................................... 151 Luggage compartment Lighting ................................................ 89 Loading .............................................. 174 Opening ........................................... 2, 26 M Main beam........................................... 9, 87 Control indicator.................................. 69 Maintenance Air conditioning system ...................... 99 Anti-freeze protection....................... 162 Brake fluid.......................................... 164 Brakes................................................. 163 Catalytic converter ............................ 114 Engine oil............................................ 160 Fuel consumption .............................. 109 Tyre pressure ............................. 122, 176 Tyres ................................................... 123 Manual transmission....................... 12, 105 Mirrors ............................................ 5, 31, 32 Misted windows ................................. 96, 98 Mobile telephone .................................... 91 Muffler, see Exhaust system ................. 114 Index N R Number plate lamps Bulb replacement............................... 148 Number plate lighting........................... 148 Number plates ....................................... 167 Radio ........................................................ 90 Radio equipment (CB)............................. 91 Rear lamp cluster .................................... 86 Bulb replacement .............................. 147 Rear window washer system ................ 150 Refuelling ............................................... 111 Fuel filler cap...................................... 111 Relays ..................................................... 138 Remote control ........................................ 22 Central locking system ........................ 22 Steering wheel...................................... 90 Replacement keys ................................... 20 Retractable steel roof ................. 17, 18, 34 Reversing lamps ...................................... 87 Bulb replacement .............................. 147 Roof load................................................ 174 Running-in.............................................. 106 Brakes ................................................. 163 O Octane numbers .................................... 170 Odometer ................................................. 72 Oil............................................................ 157 Additives............................................. 157 Topping up......................................... 157 Viscosity.............................................. 157 Oil consumption..................................... 170 Oil pressure .............................................. 68 Operating temperature......................... 107 Outside temperature gauge................... 75 Overrun................................................... 107 P Paintwork damage ................................ 150 Parking ..................................................... 14 Parking distance sensors ...................... 118 Parking lamps ............................................ 9 Parking the vehicle .................................. 14 Parts........................................................ 159 Pedals ..................................................... 107 Performance........................................... 171 Pollen filter ............................................... 99 Power steering, see EPS (Electric Power-assisted Steering) 70, 106 Preheating................................................ 69 S Safeguard against unauthorised use ....................... 13, 14, 21 Safety accessories ........................... 53, 130 Saving energy ........................................ 108 Seat adjustment ...................................... 44 Seat belts ................................... 49, 52, 151 Seat height adjustment ...................... 3, 45 Seat occupancy recognition................... 58 Seat position ............................................ 45 Seats ..................................................... 3, 44 Heated.................................................. 46 Selector lever.......................................... 101 183 Self-diagnosis ............................ 51, 58, 120 Self-help ................................................. 126 Central locking system........................ 25 Information display ............................. 76 Remote control .................................... 22 Service .................................................... 152 Service Intervals Additional work ................................. 156 Extreme operating conditions .......... 156 Service intervals..................................... 152 Main Service....................................... 152 Service work ........................................... 158 Side airbags............................................. 56 Spare keys................................................ 20 Spare wheel ................................... 131, 133 Speed ............................................. 108, 109 Fuel consumption .............................. 108 Speedometer ........................................... 72 Starting the engine ................... 13, 21, 101 Steam-jet cleaners ................................ 151 Steering column lock......................... 13, 14 Steering wheel adjustment ........................ 5 Steering wheel remote control ............... 90 Stowage compartments ............. 45, 64, 65 Sun visors ................................................. 65 System settings........................................ 78 184 Index T Tachometer.............................................. 72 Tail lamps................................................. 86 Bulb replacement............................... 147 Technical data ....................................... 168 Telephone, see Mobile telephone .......... 91 Temperature regulation.......................... 94 Temporary spare wheel ................ 125, 132 The first 600 miles (1000 km)................ 106 Tightening torque.......................... 136, 176 Time .......................................................... 76 Tools ....................................................... 133 Towing .................................................... 129 Towing eye ............................................. 129 Transmission Manual transmission ......................... 105 Transmission, Easytronic....................... 100 Driving programmes.......................... 102 fault..................................................... 104 Interruption of power supply ............ 105 Kickdown .................................... 103, 104 Selector lever ................................ 12, 101 Winter programme ............................ 103 Tread depth ........................................... 123 Trip computer .................................... 17, 81 Trip odometer .......................................... 72 Triple information display....................... 74 Turn signal lamps ................................ 9, 87 Bulb replacement............................... 146 Tyre chains ..................................... 125, 176 Tyre condition ........................................ 123 Tyre pressure.................................. 122, 176 Tyre repair aerosol ................................ 137 U Ultrasonic parking sensors ................... 118 Units of measure ..................................... 80 Unleaded fuel ........................ 110, 112, 170 V Vauxhall alarm system ........................... 29 Vauxhall genuine parts and accessories ................................... 159 Vehicle care ........................................... 150 Vehicle decommissioning ..................... 166 Vehicle identification number .............. 169 Vehicle keys, see Keys............................. 20 Vehicle recommissioning ...................... 167 Ventilation.......................................... 92, 95 W Warning buzzers ..................................... 84 Warning triangle ................................... 130 Washer fluid reservoir, windscreen washer system ................. 165 Weights .................................................. 174 Windows Demisting and defrosting ............. 96, 98 Windscreen washer system ...... 11, 85, 165 Anti-freeze protection ....................... 165 Washer fluid reservoir ....................... 165 Windscreen wipers..................... 10, 85, 165 Winter operation Battery................................................ 107 Coolant, anti-freeze .......................... 162 Fuel consumption .............................. 109 Fuel for diesel engines ...................... 110 Heating ................................................ 92 Locks .................................................. 151 Tyre chains................................. 125, 176 Window demisting and defrosting 96, 98 Windscreen washer system, anti-freeze protection ....................... 165 Winter programme................................ 103 Winter tyres.................................... 124, 176